a8k: pm: extend MSS_TRIGGER_TIMEOUT

Very rarely, during cpuidle operations the following error
is seen: "PM MSG Trigger Timeout".
This is caused by slow handling of message interrutps
in the PM FW r

a8k: pm: extend MSS_TRIGGER_TIMEOUT

Very rarely, during cpuidle operations the following error
is seen: "PM MSG Trigger Timeout".
This is caused by slow handling of message interrutps
in the PM FW running on CM3 (under heavy PM operation load).

This is not a real issue, so we extend the timeout to
avoid the error prints.

Change-Id: I92fd6f2ff1ddf208b216c123880ded28a00b6e0e
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/59670
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>

show more ...

plat/marvell: comphy: Add support for SFI on Lane 4

Add static configuration for SFI+ 10Gbps interface on SERDES
Lane 4.
This is just a copy of Lane 2 static values, not optimized.
Board-to-board ip

plat/marvell: comphy: Add support for SFI on Lane 4

Add static configuration for SFI+ 10Gbps interface on SERDES
Lane 4.
This is just a copy of Lane 2 static values, not optimized.
Board-to-board iperf test shows up to 6Gbps transfer speed.

Change-Id: I024d2ac132f7fa6c342a64367f3dca2123a27e97
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>

show more ...

fix: a3900: pm: fix number of CPU power switches.

- Number of open power switches for CPUs should be three
and now two.

- This patch updates the value of open power switches from
0xfd (two powe

fix: a3900: pm: fix number of CPU power switches.

- Number of open power switches for CPUs should be three
and now two.

- This patch updates the value of open power switches from
0xfd (two power-switches) to 0xfc (three power-switches).

Change-Id: I2783ab7f04bbbb6da78eeedcabe4636f9a774512
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

show more ...

svc: Update the EEPROM AVS values processing

Add support for SVC test builds for tuning AVS values.
Update the SVC procedure and add EEPROM access.
Add support for AP807 AVS values (10 bits wide).

svc: Update the EEPROM AVS values processing

Add support for SVC test builds for tuning AVS values.
Update the SVC procedure and add EEPROM access.
Add support for AP807 AVS values (10 bits wide).

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

ble: ap807: Switch to PLL mode and update CPU frequency

- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock

Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0

ble: ap807: Switch to PLL mode and update CPU frequency

- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock

Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

mvebu: cp110: avoid pcie power on/off sequence when called from Linux

In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it c

mvebu: cp110: avoid pcie power on/off sequence when called from Linux

In Armada 8K DB boards, PCIe initialization can be executed only once
because PCIe reset performed during chip power on and it cannot be
executed via GPIO later.
This means that power on can be executed only once, when it's called
from the bootloader.
Power on:
Read bit 21 of the mode, it marks if the caller is
the bootloader or the Linux Kernel.
Power off:
Check if the comphy was already configured to PCIe, if yes,
check if the caller is bootloader, if both conditions are true
(PCIe mode and called by Linux) - skip the power-off.

In addition, fix incorrect documentation describing mode fields -
PCIe width is 3 bits, not 2.

NOTE: with this patch, please use LK4.14.76 (LK4.4.120 may not work
with it).

Change-Id: I4b929011f97a0a1869a51ba378687e78b3eca4ff
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

show more ...

plat: marvell: a3700: do not power off cpu due to errata ref #13

Do not power off the CPU1 since there is no way to wake it up
(wake-up is causing CPU0 reset as well duo to HW bug). Quote from errat

plat: marvell: a3700: do not power off cpu due to errata ref #13

Do not power off the CPU1 since there is no way to wake it up
(wake-up is causing CPU0 reset as well duo to HW bug). Quote from errata
Ref #13 [In power saving mode, both cores must be powered off]:
"When Core 0 is on and Core 1 is in power-off state, a Core 1
wake-up resets Core 0 as well and puts Core 0 back to ROM".

To overcome described HW bug instead of powering the CPU off, let it
reach WFI instruction, which is invoked by generic psci_do_cpu_off
function after platform handler finishes. This will put the core in low
power state and give a chance to wake it up.

Before this change, after running secondary kernel via kexec, only one
core was up, now both cores are up.

Change-Id: I87f144867550728055d9b8a2edb84a14539acab7
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

show more ...

plat/marvell: Migrate to multi-console API

Migrate Marvell platforms from legacy console API to
multi-console API.

Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Por

plat/marvell: Migrate to multi-console API

Migrate Marvell platforms from legacy console API to
multi-console API.

Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

fix: plat/marvell: a3700: Remove encryption password

According to "openssl" manual:
-K key
The actual key to use: this must be represented as a string
comprised only of hex digits. If only the key i

fix: plat/marvell: a3700: Remove encryption password

According to "openssl" manual:
-K key
The actual key to use: this must be represented as a string
comprised only of hex digits. If only the key is specified,
the IV must additionally specified using the -iv option.
When both a key and a password are specified, the key given
with the -K option will be used and the IV generated from the
password will be taken.
It does not make much sense to specify both key and password.

This patch removes "-k 0" parameter from the encryption command
since we are already using "-K" and "-iv" for the key and IV.

Change-Id: Ia333cedaa3207e643c95d2ec7c229f50eeab96db
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60745
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Sharon Habet <sharonh@marvell.com>

show more ...

Standardise header guards across codebase

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this proje

Standardise header guards across codebase

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

Merge pull request #1623 from MISL-EBU-System-SW/a3700-support

Add support for Armada 3700 and COMPHY porting layer

plat: marvell: Add support for Armada-37xx SoC platform

Add supprot for Marvell platforms based on Armada-37xx SoC.
This includes support for the official Armada-3720 modular
development board and E

plat: marvell: Add support for Armada-37xx SoC platform

Add supprot for Marvell platforms based on Armada-37xx SoC.
This includes support for the official Armada-3720 modular
development board and EspressoBin community board.
The Armada-37xx SoC contains dual Cortex-A53 Application CPU,
single secure CPU (Cortex-M3) and the following interfaces:
- SATA 3.0
- USB 3.0 and USB 2.0
- PCIe
- SDIO (supports boot from eMMC)
- SPI
- UART
- I2c
- Gigabit Ethernet

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

Add plat_crash_console_flush to platforms without it

Even though at this point plat_crash_console_flush is optional, it will
stop being optional in a following patch.

The console driver of warp7 do

Add plat_crash_console_flush to platforms without it

Even though at this point plat_crash_console_flush is optional, it will
stop being optional in a following patch.

The console driver of warp7 doesn't support flush, so the implementation
is a placeholder.

TI had ``plat_crash_console_init`` and ``plat_crash_console_putc``, but
they weren't global so they weren't actually used. Also, they were
calling the wrong functions.

imx8_helpers.S only has placeholders for all of the functions.

Change-Id: I8d17bbf37c7dad74e134c61ceb92acb9af497718
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

tools: Move doimage to marvell folder for future add-ons

Move doimage utility from toos/doimage to tools/marvell/doimage.
This is done for supporting mode Marvell tools in the future.

Signed-off-by

tools: Move doimage to marvell folder for future add-ons

Move doimage utility from toos/doimage to tools/marvell/doimage.
This is done for supporting mode Marvell tools in the future.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

mvebu: cp110: introduce COMPHY porting layer

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length

mvebu: cp110: introduce COMPHY porting layer

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.

Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h

If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".

The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

Merge pull request #1621 from jts-arm/typos

Various corrections of typos

Replace S-EL3 references by EL3

The "Secure" prefix (S-ELx) is valid only for S-EL0 and S-EL1 but is
meaningless for EL3, since EL3 is always secure. Hence, the "S" prefix
has been removed from wher

Replace S-EL3 references by EL3

The "Secure" prefix (S-ELx) is valid only for S-EL0 and S-EL1 but is
meaningless for EL3, since EL3 is always secure. Hence, the "S" prefix
has been removed from wherever it was used as "S-EL3".

Change-Id: Icdeac9506d763f9f83d7297c7113aec7b85e9dbe
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

show more ...

plat: marvell: invoke platform specific scp_bl2 image handler

Before switching to new API the scp_bl2 handler was invoked from
bl2/bl2_image_load.c which was removed. Invoke the platform specific
sc

plat: marvell: invoke platform specific scp_bl2 image handler

Before switching to new API the scp_bl2 handler was invoked from
bl2/bl2_image_load.c which was removed. Invoke the platform specific
scp_bl2 handler in analogy to ARM and HiSilicon.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

marvell: Move BLE from external repo to the platform folder

The BLE is the pre-TF-A boot stage required by Marvell Armada
BootROM for bringing up DRAM and allow the boot image copy to it.
Since this

marvell: Move BLE from external repo to the platform folder

The BLE is the pre-TF-A boot stage required by Marvell Armada
BootROM for bringing up DRAM and allow the boot image copy to it.
Since this is not a standard boot level and only uses the TF-A
as a build environment, it was introduced out of source tree.
However it turns out that such remote location introduces additional
complexity to the upstream TF-A build process.
In order to simplify the build environment the BLE source folder
is relocated from the external repository to A8K platform directory.
The build documentation is updated accordingly.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

marvell: Continue migration to new APIs

- Fix build issue
- Add initial memory parameters descriptors for BL2
- Migrate to image load V2

Basic build and run test passed on MacchiatoBin board.
Need

marvell: Continue migration to new APIs

- Fix build issue
- Add initial memory parameters descriptors for BL2
- Migrate to image load V2

Basic build and run test passed on MacchiatoBin board.
Need to fix the service CPU (CM3) image load procesure and test
OPTEE functionality, which probably will require additional work.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

marvell: Migrate to new interfaces

- Migrate to bl2_early_platform_setup2().
- Remove references to removed build options.
- Use private definition of bl31_params_t.

This is an incomplete migration

marvell: Migrate to new interfaces

- Migrate to bl2_early_platform_setup2().
- Remove references to removed build options.
- Use private definition of bl31_params_t.

This is an incomplete migration, the platform doesn't currently compile.

Change-Id: I1ae477b1f2489f49b651528050fdf06e4a55e425
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

drivers: i2c: mentor: move platform code into header files

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change t

drivers: i2c: mentor: move platform code into header files

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

show more ...

drivers: mentor: extract MI2CV driver from Marvell driver

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of custom

drivers: mentor: extract MI2CV driver from Marvell driver

The Marvell A8K SoCs use the MI2CV IP core from Mentor Graphics, which
is also used by Allwinner.

As Mentor Graphics allows a lot of customization, the MI2CV in the two
SoC families are not compatible, and driver modifications are needed.

Extract the common code to a MI2CV driver.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

show more ...

plat: marvell: Update Marvell base code version to 18.09.1

Change-Id: I908844364bf8080612aaa6d750d7d2441ecc2eb8
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

plat: svc: ap807: add SVC configuration for AP807

- add svc configuration according to values burnt
to the chip efuse

Change-Id: Icf5d7cc41bc09ac2244d0a126106e681afebb064
Signed-off-by: Christine

plat: svc: ap807: add SVC configuration for AP807

- add svc configuration according to values burnt
to the chip efuse

Change-Id: Icf5d7cc41bc09ac2244d0a126106e681afebb064
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

show more ...