Merge branch 'master' of git://git.denx.de/u-boot-net

drivers: net: vsc9953: Add LAG support

You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}

A port must belong to a single LA

drivers: net: vsc9953: Add LAG support

You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}

A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.

For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

drivers: net: vsc9953: Fix FDB aging time

By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.

Signed-off-by: Codri

drivers: net: vsc9953: Fix FDB aging time

By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

drivers: net: vsc9953: Fix number of reserved registers

There are only 21 registers reserved between ana_ana and
ana_pgid register groups.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freesc

drivers: net: vsc9953: Fix number of reserved registers

There are only 21 registers reserved between ana_ana and
ana_pgid register groups.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge remote-tracking branch 'u-boot/master'

Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq

drivers/net/vsc9953: Add GPL-2.0+ SPDX-License-Identifier

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun

drivers/net/vsc9953: Add GPL-2.0+ SPDX-License-Identifier

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add command for shared/private VLAN learning

The command:
ethsw vlan fdb { [help] | show | shared | private }
- make VLAN learning shared or private"

configures the FDB to sha

drivers/net/vsc9953: Add command for shared/private VLAN learning

The command:
ethsw vlan fdb { [help] | show | shared | private }
- make VLAN learning shared or private"

configures the FDB to share the FDB entries learned on multiple VLANs
or to keep them separated. By default, the FBD uses private VLAN
learning. This command has also been added to the ethsw generic parser
from common/cmd_ethsw.c

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add VLAN commands for VSC9953

The new added commands can be used to configure VLANs for a port
on both ingress and egress.

The new commands are:
ethsw [port <port_no>] pvid { [

drivers/net/vsc9953: Add VLAN commands for VSC9953

The new added commands can be used to configure VLANs for a port
on both ingress and egress.

The new commands are:
ethsw [port <port_no>] pvid { [help] | show | <pvid> }
- set/show PVID (ingress and egress VLAN tagging) for a port;
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> }
- add a VLAN to a port (VLAN members);
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid }
- set egress tagging mod for a port"
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified }
- Configure VID source for egress tag. Tag's VID could be the
frame's classified VID or the PVID of the port
These commands have also been added to the ethsw generic parser from
common/cmd_ethsw.c

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add commands to manipulate the FDB for VSC9953

The new command:
ethsw [port <port_no>] [vlan <vid>] fdb
{ [help] | show | flush | { add | del } <mac> }

Can be used to a

drivers/net/vsc9953: Add commands to manipulate the FDB for VSC9953

The new command:
ethsw [port <port_no>] [vlan <vid>] fdb
{ [help] | show | flush | { add | del } <mac> }

Can be used to add and delete FDB entries. Also, the command can be used
to show entries from the FDB tables. When used with [port <port_no>]
and [vlan <vid>], only the matching the FDB entries can be seen or
flushed. The command has also been added to the generic ethsw parser
from cmd_ethsw.c.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add commands to enable/disable HW learning

The command:
ethsw [port <port_no>] learning { [help] | show | auto | disable }

can be used to enable/disable HW learning on a port.

drivers/net/vsc9953: Add commands to enable/disable HW learning

The command:
ethsw [port <port_no>] learning { [help] | show | auto | disable }

can be used to enable/disable HW learning on a port.
This patch also adds this command to the generic ethsw parser from
cmd_ethsw.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add command to show/clear port counters

The new added command:
ethsw [port <port_no>] statistics { [help] | [clear] }

will print counters like the number of Rx/Tx frames,
numbe

drivers/net/vsc9953: Add command to show/clear port counters

The new added command:
ethsw [port <port_no>] statistics { [help] | [clear] }

will print counters like the number of Rx/Tx frames,
number of Rx/Tx bytes, number of Rx/Tx unicast frames, etc.
This patch also adds this commnd in the genereric ethsw
parser from cmd_ethsw.c

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Add default configuration for VSC9953 L2 Switch

At startup, the default configuration should be:
- enable HW learning on all ports (HW default);
- all ports are VLAN aware;
-

drivers/net/vsc9953: Add default configuration for VSC9953 L2 Switch

At startup, the default configuration should be:
- enable HW learning on all ports (HW default);
- all ports are VLAN aware;
- all ports are members of VLAN 1;
- all ports have Port-based VLAN 1;
- on all ports, the switch is allowed to remove
maximum one VLAN tag,
- on egress, the switch should add a VLAN tag if the
frame is classified to a different VLAN than the port's
Port-based VLAN;

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Fix missing reserved register

The VSC9953 DS reserves a register between vlan_mask and anag_efil
registers.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-of

drivers/net/vsc9953: Fix missing reserved register

The VSC9953 DS reserves a register between vlan_mask and anag_efil
registers.

Signed-off-by: Johnson Leung <johnson.leung@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Fix bug when enabling a port

When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and def

drivers/net/vsc9953: Fix bug when enabling a port

When a port is enabled at init time, the initializing function
touches more bits than necessary to enable a port (also touches
reserved bits and default bit values). This patch fixes this issue
by changing the value of the define used to enable the port and
assures that no other bits are changes by replacing out_le32()
with setbits_le32().

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Cleanup patch

This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "p

drivers/net/vsc9953: Cleanup patch

This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" words are replaced with "port_no",
puts each variable declaration on a line and removes
unnecessary tabs.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

drivers/net/vsc9953: Remove 'CONFIG_' from macros' name

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <y

drivers/net/vsc9953: Remove 'CONFIG_' from macros' name

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

net/vsc9953: Add driver for Vitesse VSC9953 L2 Switch IP

This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Etherne

net/vsc9953: Add driver for Vitesse VSC9953 L2 Switch IP

This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Ethernet ports: 2 internal fixed-links
(ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps.
The external ports may be connected to PHYs over QSGMII and SGMII.

Commands have also been added to enable/disable a port and to
check a port's link speed, duplexity and status. The commands are:

ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
ethsw port <port_nr> show - show an l2 switch port's configuration

port_nr=0..9; use "all" for all ports

For more detailse please see doc/README.t1040-l2switch

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...