rockchip: rk3399: Fix CAS latency setting

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.

Signed-off-by: Derek Basehore <dbasehore

rockchip: rk3399: Fix CAS latency setting

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: disable training modules after DDR DFS

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training mo

rockchip: rk3399: disable training modules after DDR DFS

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: rk3399: Move DQS drive strength setting to M0

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength

rockchip: rk3399: Move DQS drive strength setting to M0

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: Remove dram dfs optimization

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some regis

rockchip: rk3399: Remove dram dfs optimization

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some registers do not have a copy per frequency index, so this
optimization might be causing problems.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: Save and restore RX_CAL_DQS values

We were getting far off values on resume for the RX_CAL_DQS values.
This saves and restores the values for suspend/resume until the root
of the p

rockchip: rk3399: Save and restore RX_CAL_DQS values

We were getting far off values on resume for the RX_CAL_DQS values.
This saves and restores the values for suspend/resume until the root
of the problem is figured out

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: Add MIN() and MAX() macros back to M0 code

These macros were accidentally deleted in a previous cleanup. This
slipped through because the code using them is currently unused, but
that may

rockchip: Add MIN() and MAX() macros back to M0 code

These macros were accidentally deleted in a previous cleanup. This
slipped through because the code using them is currently unused, but
that may change in the future.

Signed-off-by: Julius Werner <jwerner@chromium.org>

show more ...

rockchip: Clean up M0 Makefile, clarify float-abi

This patch shuffles the M0 Makefile flags around a bit trying to make
their purpose clearer and remove duplication. Since all three build
steps (com

rockchip: Clean up M0 Makefile, clarify float-abi

This patch shuffles the M0 Makefile flags around a bit trying to make
their purpose clearer and remove duplication. Since all three build
steps (compiling, assembling, linking) actually call GCC, remove the
misleading aliases $(AS) and $(LD) to avoid confusion that those tools
might be called directly. Split flags into a common group that has
meaning for all three steps and separate variables specific to each
step. Remove -nostartfiles which is a strict subset of -nostdlib.

Also add explicit parameters for -mfloat-abi=soft, -fomit-frame-pointer
and -fno-common. If omitted these settings depend on the toolchain's
built-in default and cause various problems if they resolve to
unexpected values.

Signed-off-by: Julius Werner <jwerner@chromium.org>

show more ...

rockchip: rk3399: Clean up and seprate secure parts from SoC codes

The goal is that make clear the secure and SoC codes. Now cleaning them
will help secure code extensions for RK3399 in the future.

rockchip: rk3399: Clean up and seprate secure parts from SoC codes

The goal is that make clear the secure and SoC codes. Now cleaning them
will help secure code extensions for RK3399 in the future.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: rk3399: sperate the BL31 parameters for sharing

Maybe the coreboot will reference the BL31 parameters (e.g the TZRAM_BASE
and TZRAM_SIZE for DDR secure regions), we can split them and don'

rockchip: rk3399: sperate the BL31 parameters for sharing

Maybe the coreboot will reference the BL31 parameters (e.g the TZRAM_BASE
and TZRAM_SIZE for DDR secure regions), we can split them and don't have
to hardcode the range in two places.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: rk3399: configure the DDR secure region for BL31 image

Move the BL31 loaded base address 0x10000 to 0x1000, and configure
the the memory range 0~1MB is secure, the goal is that make sure
t

rockchip: rk3399: configure the DDR secure region for BL31 image

Move the BL31 loaded base address 0x10000 to 0x1000, and configure
the the memory range 0~1MB is secure, the goal is that make sure
the BL31 image will be not modified.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: Clean up header and referenced files

So far, there are more and more features are supported on the RK3399,
meanwhile, these features are increasingly being defined and intertwined.
It's ti

rockchip: Clean up header and referenced files

So far, there are more and more features are supported on the RK3399,
meanwhile, these features are increasingly being defined and intertwined.
It's time to clean up and make them clearer.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: rk3399: Don't wait for vblank in M0 for ddrfreq

This removes waiting for vblank on the M0 during ddrfreq transitions.
That will now be done in the kernel to allow scheduling to be done on

rockchip: rk3399: Don't wait for vblank in M0 for ddrfreq

This removes waiting for vblank on the M0 during ddrfreq transitions.
That will now be done in the kernel to allow scheduling to be done on
the CPU core that changes the ddr frequency. Waiting for vblank in
the M0 would have the CPU core that waits on the M0 spin looping for
up to 16ms (1 frame for the display).

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: restore PMU_CRU_GATEDIS_CON0 value after ddr dvfs

we will set PMU_CRU_GATEDIS_CON0 when idle port, it will enable
all clock, for save power consumption, we need to restore old valu

rockchip: rk3399: restore PMU_CRU_GATEDIS_CON0 value after ddr dvfs

we will set PMU_CRU_GATEDIS_CON0 when idle port, it will enable
all clock, for save power consumption, we need to restore old value
when finish it.

Signed-off-by: Lin Huang <hl@rock-chips.com>

show more ...

rockchip: rk3399: fix PMU_CRU_GATEDIS_CON0 setting error

As rk3399 TRM1.1 document show, when set PMU_CRU_GATEDIS_CON0/1
register, it need set the write_mask bit (bit16 ~ bit31), but as
we test, it

rockchip: rk3399: fix PMU_CRU_GATEDIS_CON0 setting error

As rk3399 TRM1.1 document show, when set PMU_CRU_GATEDIS_CON0/1
register, it need set the write_mask bit (bit16 ~ bit31), but as
we test, it not need it. So need to correct the setting way, otherwise
it will set wrong value to this register.

Signed-off-by: Lin Huang <hl@rock-chips.com>

show more ...

FIXUP: rockchip: rk3399: fix the incorrect bit during m0_init

We found that the DUT will be hanged if we don't set the bit_1 of the
PMUCRU_GATEDIS_CON0. But, from the TRM, there is weird that the bi

FIXUP: rockchip: rk3399: fix the incorrect bit during m0_init

We found that the DUT will be hanged if we don't set the bit_1 of the
PMUCRU_GATEDIS_CON0. But, from the TRM, there is weird that the bit_1
is set the clk_center1_gating_dis, not clk_pmum0_gating_dis. Is the
TRM incorrect? We need to check it with the IC team and re-clean the
commit message and explain it tomorrow.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip: rk3399: improve the m0 enable flow

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock f

rockchip: rk3399: improve the m0 enable flow

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock for ddr dvfs.
3. Correct the clk_pmum0_gating_dis bit, it is BIT0 not BIT1
4. do not set/clear hclk_noc_pmu_en in M0 code, it does not relate
to the M0 clock.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: check vop status when we wait dma finish flag

When vop is disabled and we read the vop register the system will
hang, so check vop status when we wait for the DMA finish flag to
av

rockchip: rk3399: check vop status when we wait dma finish flag

When vop is disabled and we read the vop register the system will
hang, so check vop status when we wait for the DMA finish flag to
avoid this sitiuation. This is done by checking for standby, DMA stop
mode, and disabled window states. Any one of these will prevent the
DMA finish flag from triggering.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: add stopwatch functions to m0

There is system timer in m0, we can use it to implement a set of
stopwatch functions for measuring timeouts.

Signed-off-by: Lin Huang <hl@rock-chips.

rockchip: rk3399: add stopwatch functions to m0

There is system timer in m0, we can use it to implement a set of
stopwatch functions for measuring timeouts.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: dram: set all ddr frequency pll_postdiv values to 0

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Sig

rockchip: rk3399: dram: set all ddr frequency pll_postdiv values to 0

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: enable CA training when do ddr dfs

For ddr dfs stable, We need to enable ddr CA training
when do ddr dfs.

Signed-off-by: Lin Huang <hl@rock-chips.com>

rockchip: rk3399: fix hang in ddr set rate

This fixes a hang with setting the DRAM rate based on a race condition
with the M0 which sets the DRAM rate. The AP can also starve the M0,
so this also de

rockchip: rk3399: fix hang in ddr set rate

This fixes a hang with setting the DRAM rate based on a race condition
with the M0 which sets the DRAM rate. The AP can also starve the M0,
so this also delays the AP reads to the DONE parameter for the M0.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: Enable per CS training at 666MHz

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value

rockchip: rk3399: Enable per CS training at 666MHz

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value, this also adds a new value for that.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

show more ...

rockchip: rk3399: add support for ddrfreq suspend/resume

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
fre

rockchip: rk3399: add support for ddrfreq suspend/resume

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
frequency transition. It just configures registers so the training on
resume for both indices will be correct.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rk3399: dram: use PMU M0 to do ddr frequency scaling

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can als

rk3399: dram: use PMU M0 to do ddr frequency scaling

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can also work for ddr frequency scaling, so let's use it.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

show more ...

rockchip/rk3399: Cleanup platform.mk file

This makes the file consistently use tabs instead of mixing in spaces.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>