Home
last modified time | relevance | path

Searched refs:DIP (Results 1 – 25 of 60) sorted by relevance

123

/OK3568_Linux_fs/u-boot/board/cadence/xtfpga/
H A DREADME51 The LX60/LX110/LX200/ML605 contain an 8-way DIP switch that controls
55 Boot Mapping (DIP switch 8):
57 DIP switch 8 maps the system ROM address space (in which the
60 and cannot be disabled by software, therefore DIP switch 8 is no
61 available for application use. Note DIP switch 7 is reserved by
80 Default MAC Address (DIP switches 1-6):
84 value whose least significant 6 bits come from DIP switches 1-6.
86 according to the DIP switches, where "on"==1 and "off"==0, and
93 used and the DIP switches no longer consulted. DIP swithes 1-6
96 The KC705 board contains 4-way DIP switch, way 1 is the boot mapping
/OK3568_Linux_fs/kernel/Documentation/driver-api/serial/
H A Drocket.rst28 The RocketPort ISA board requires I/O ports to be configured by the DIP
30 information on how to set the DIP switches.
92 card before installing and using it. This is done by setting a set of DIP
103 0x300h, 0x340h, 0x380h. This I/O address must be reflected in the DIP
111 software control. The DIP switch settings for the I/O address must be
116 Rocketport board must be set with the DIP switches corresponding to
117 the first board, the second board must be set with the DIP switches
119 the only place where the DIP switch settings should differ between the
145 DIP Switches DIP Switches
153 DIP Switches I/O Address Range
/OK3568_Linux_fs/u-boot/board/phytec/pcm058/
H A DREADME25 The dip switch "DIP-1" on the board let choose between
28 DIP-1 set to off: Boot first from NAND, then try SPI
29 DIP-1 set to on: Boot first from SD, then try SPI
31 The bootloader was tested with DIP-1 set to on. If a SD-card
/OK3568_Linux_fs/buildroot/board/solidrun/macchiatobin/
H A Dreadme.txt42 On Rev 1.2 board to select boot from SD-card the DIP switches
49 of the SW1/2 DIP switches. To boot from SD-card the setting of J1
50 jumpers should match the DIP switches of Rev v1.2 board
/OK3568_Linux_fs/u-boot/board/freescale/p2041rdb/
H A DREADME36 5. Change DIP-switch
59 5. Change DIP-switch
84 5. Change DIP-switch
/OK3568_Linux_fs/u-boot/board/freescale/mpc8610hpcd/
H A DREADME70 DIP Switch Settings
72 To manually switch the flash banks using the DIP switch
/OK3568_Linux_fs/u-boot/board/freescale/p1_p2_rdb_pc/
H A DREADME37 SD width is based off DIP switch. DIP switch is detected on the
/OK3568_Linux_fs/u-boot/board/freescale/mx28evk/
H A DREADME17 To boot MX28EVK from an SD card, set the boot mode DIP switches as:
26 To boot MX28EVK from SPI NOR flash, set the boot mode DIP switches as:
/OK3568_Linux_fs/u-boot/board/freescale/mpc8315erdb/
H A DREADME8 To boot the image at 0xFE000000 in NOR flash, use these DIP
19 DIP switch settings for S3 S4:
/OK3568_Linux_fs/u-boot/board/freescale/mpc8313erdb/
H A DREADME8 To boot the image at 0xFE000000 in NOR flash, use these DIP
19 DIP switch settings for S3 S4:
/OK3568_Linux_fs/u-boot/board/renesas/sh7785lcr/
H A DREADME.sh7785lcr21 This board has 2 physical memory maps. It can be changed with DIP switch(S2-5).
86 - dipsw : test DIP switch
/OK3568_Linux_fs/u-boot/board/renesas/alt/
H A DKconfig19 DIP switch of board in order to use this function.
/OK3568_Linux_fs/u-boot/board/freescale/p1010rdb/
H A DREADME.P1010RDB-PB62 P1010RDB-PB default DIP-switch settings
71 P1010RDB-PB boot mode settings via DIP-switch
80 Switch P1010RDB-PB boot mode via software without setting DIP-switch
/OK3568_Linux_fs/buildroot/board/sifive/hifive-unleashed/
H A Dreadme.txt64 Make sure that the all DIP switches are set to the off position for
114 Make sure that the all DIP switches are set to the off position for
/OK3568_Linux_fs/u-boot/board/freescale/mpc832xemds/
H A DREADME4 1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board
102 1)Make sure the DIP SW support PCI mode as described in Section 1.1.
/OK3568_Linux_fs/u-boot/board/freescale/t102xrdb/
H A DREADME202 via DIP-switch: set SW3[5:7] = '100'
205 via DIP-switch: set SW3[5:7] = '100'
210 via DIP-Switch: set SW3[5:7] = '000'
213 via DIP-switch: set SW3[5:7] = '000'
/OK3568_Linux_fs/buildroot/board/embest/riotboard/
H A Dreadme.txt31 side of SW1 DIP switches. Configure the SW1 swiches like this:
/OK3568_Linux_fs/u-boot/board/freescale/t208xrdb/
H A DREADME139 T2080PCIe-RDB Default DIP-Switch setting
159 via DIP-switch: set SW3[5:7] = '100'
163 via DIP-Switch: set SW3[5:7] = '000'
/OK3568_Linux_fs/buildroot/board/kontron/pitx-imx8m/
H A Dreadme.txt61 * Make sure the boot source selection DIP switches are set correctly
/OK3568_Linux_fs/buildroot/board/freescale/imx6sabre/
H A Dreadme.txt117 - Set the SW10, SW11 and SW12 DIP switches at the top of the board in
143 - Set the S1, S2 and S3 DIP switches and J3 jumper to boot from SD on CPU card.
/OK3568_Linux_fs/buildroot/board/solidrun/clearfog_gt_8k/
H A Dreadme.txt33 To select boot from SD-card the DIP switches in SW6 (at the bottom of the
/OK3568_Linux_fs/buildroot/board/solidrun/clearfog/
H A Dreadme.txt55 - Set up the DIP switches for microSD boot. The correct values are:
/OK3568_Linux_fs/yocto/poky/meta/recipes-devtools/valgrind/valgrind/
H A DAdded-support-for-PPC-instructions-mfatbu-mfatbl.patch88 + DIP("mfspr r%u,%u", rD_addr, (UInt)SPR);
/OK3568_Linux_fs/u-boot/board/freescale/t102xqds/
H A DREADME193 SerDes clock vs DIP-switch settings
225 via DIP-switch: set SW6[1:4] = '0100'
229 via DIP-Switch: set SW6[1:4] = '0000'
/OK3568_Linux_fs/u-boot/doc/
H A DREADME.mxs142 To boot a MXS based board from SD, set the boot mode DIP switches according to
191 To boot a MX28 based board from NAND, set the boot mode DIP switches according
287 Power off the board and set the boot mode DIP switches to boot from the SPI NOR

123