Home
last modified time | relevance | path

Searched full:sw4 (Results 1 – 25 of 105) sorted by relevance

12345

/OK3568_Linux_fs/u-boot/board/freescale/p1010rdb/
H A DREADME.P1010RDB-PB67 SW4[1:4]= 1010
73 SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot
74 SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot
75 SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot
76 SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot
153 set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
157 set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
162 Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board
168 set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board
175 set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board
H A DREADME.P1010RDB-PA82 SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash
83 SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash
84 SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash
111 3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on.
146 3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on.
165 3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on.
/OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/regulator/
H A Dltc3676.txt8 - regulators: Contains eight regulator child nodes sw1, sw2, sw3, sw4,
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
20 Regulators sw1, sw2, sw3, sw4 can regulate the feedback reference from:
63 sw4_reg: sw4 {
H A Dpv88060.txt11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
104 SW4 {
105 regulator-name = "sw4";
H A Dpfuze100.yaml15 sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6
132 sw4_reg: sw4 {
/OK3568_Linux_fs/kernel/arch/arm/boot/dts/
H A Dimx28-eukrea-mbmx28lc.dtsi35 button-sw4 {
40 sw4 {
41 label = "SW4";
202 gpio_button_sw4_pins_mbmx28lc: gpio-button-sw4-mbmx28lc@0 {
H A Dsun8i-h3-orangepi-lite.dts93 sw4 {
94 label = "sw4";
H A Dsun8i-h3-orangepi-2.dts100 sw4 {
101 label = "sw4";
H A Dsun8i-h3-orangepi-one.dts92 sw4 {
93 label = "sw4";
H A Dsun8i-h3-orangepi-pc.dts92 sw4 {
93 label = "sw4";
/OK3568_Linux_fs/buildroot/board/freescale/imx8mpevk/
H A Dreadme.txt62 SW4: 0011 SW4[1-4]
/OK3568_Linux_fs/u-boot/board/freescale/mpc8641hpcn/
H A DREADME48 SW4(1-2) = 11 CONFIG_SYS_HOSTMODE = 11 :: both prots host/root
49 SW4(3-4) = 11 CONFIG_SYS_BOOTSEQ = 11 :: no boot seq
50 SW4(5-8) = 0011 CONFIG_SYS_IOPORT = 0011 :: both PEX
/OK3568_Linux_fs/u-boot/doc/
H A DREADME.mpc85xxcds135 SW4=10001000
160 SW4=11111110
174 SW4=11110011
/OK3568_Linux_fs/u-boot/board/freescale/common/
H A Dmc34vr500.c31 if (sw > SW4) { in mc34vr500_get_sw_volt()
70 if (sw > SW4 || sw_volt < 625) in mc34vr500_set_sw_volt()
/OK3568_Linux_fs/u-boot/board/freescale/mpc837xemds/
H A DREADME17 SW4[8] is the bit labeled 8 on Switch 4.
27 SW4[1-8]= 0000_0110 (core PLL setting)
/OK3568_Linux_fs/u-boot/board/freescale/ls1046ardb/
H A Dls1046ardb.c112 return mc34vr500_get_sw_volt(SW4); in get_serdes_volt()
117 return mc34vr500_set_sw_volt(SW4, svdd); in set_serdes_volt()
/OK3568_Linux_fs/u-boot/board/freescale/mpc832xemds/
H A DREADME18 SW4[8] is the bit labeled 8 on Switch 4.
29 SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting)
/OK3568_Linux_fs/kernel/arch/arm64/boot/dts/allwinner/
H A Dsun50i-h5-orangepi-prime.dts54 sw4 {
55 label = "sw4";
H A Dsun50i-h5-orangepi-pc2.dts60 sw4 {
61 label = "sw4";
/OK3568_Linux_fs/u-boot/arch/arm/dts/
H A Dsun8i-h3-orangepi-one.dts85 sw4 {
86 label = "sw4";
H A Dsun8i-h3-orangepi-lite.dts87 sw4 {
88 label = "sw4";
H A Dsun8i-h3-orangepi-pc.dts85 sw4 {
86 label = "sw4";
H A Dsun8i-h3-orangepi-2.dts93 sw4 {
94 label = "sw4";
/OK3568_Linux_fs/kernel/drivers/regulator/
H A Dltc3676.c172 /* SW1, SW2, SW3, SW4 linear 0.8V-3.3V with scalar via R1/R2 feeback res */
228 LTC3676_LINEAR_REG(SW4, sw4, BUCK4, DVB4A),
/OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/mfd/
H A Dmc13xxx.txt89 sw4 : regulator SW4 (register 27, bit 0)

12345