lib/mmio: Add mmio_clrsetbits_16 inline function

Add 16-bit variant of mmio_clrsetbits function

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marv

lib/mmio: Add mmio_clrsetbits_16 inline function

Add 16-bit variant of mmio_clrsetbits function

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...

Merge pull request #1582 from ldts/rcar_gen3/upstream

rcar_gen3: initial support

Merge pull request #1553 from glneo/dcache-late-disable

Allow D-Cache to remain on during core power-down

Merge pull request #1629 from robertovargas-arm/hw-assisted-coherency-lock

Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled

Merge pull request #1631 from deepan02/deepak-arm/relocate-jump_if_cpu_midr

plat/arm: relocate the jump_if_cpu_midr macro.

Merge pull request #1628 from antonio-nino-diaz-arm/an/sharing

plat/arm: Small reorganization of platform code

rcar_gen3: drivers: watchdog

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: serial controller interface

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: spi multio bus controller

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: rom api

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: power controller

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: console

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: io [emmc/mem]

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: i2c dvfs

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: emmc

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: dma

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: micro delay generator

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: cpld

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: board identification

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: avs [adaptive voltage scaling]

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: authentication

Signed-off-by: ldts <jramirez@baylibre.com>

rcar_gen3: drivers: staging

- ddr
- pfc [pin function controller]
- qos [bandwidth]

checkpatch.pl is generating too many errors.

rcar-gen3: initial commit for the rcar-gen3 boards

Reference code:
==============

rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]

Author

rcar-gen3: initial commit for the rcar-gen3 boards

Reference code:
==============

rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]

Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date: Thu Aug 30 21:26:41 2018 +0900
Update IPL and Secure Monitor Rev1.0.22

General Information:
===================

This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).

Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls

$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed

Other dependencies:
------------------
* mbed_tls:
git@github.com:ARMmbed/mbedtls.git [devel]

Merge: 68dbc94 f34a4c1
Author: Simon Butcher <simon.butcher@arm.com>
Date: Thu Aug 30 00:57:28 2018 +0100

* optee_os:
https://github.com/BayLibre/optee_os

Until it gets merged into OP-TEE, the port requires Renesas' Trusted
Environment with a modification to support power management.

Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
Date: Thu Aug 30 16:49:49 2018 +0200
plat-rcar: cpu-suspend: handle the power level
Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>

* u-boot:
The port has beent tested using mainline uboot.

Author: Fabio Estevam <festevam@gmail.com>
Date: Tue Sep 4 10:23:12 2018 -0300

*linux:
The port has beent tested using mainline kernel.

Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Sep 16 11:52:37 2018 -0700
Linux 4.19-rc4

Overview
---------

BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)

BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).

During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.

Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.

To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).

Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.

[1] https://github.com/renesas-rcar/arm-trusted-firmware
Tests
-----

* cpuidle
-------
enable kernel's cpuidle arm_idle driver and boot

* system suspend
--------------
$ cat suspend.sh
#!/bin/bash
i2cset -f -y 7 0x30 0x20 0x0F
read -p "Switch off SW23 and press return " foo
echo mem > /sys/power/state

* cpu hotplug:
------------
$ cat offline.sh
#!/bin/bash
nbr=$1
echo 0 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

$ cat online.sh
#!/bin/bash
nbr=$1
echo 1 > /sys/devices/system/cpu/cpu$nbr/online
printf "ONLINE: " && cat /sys/devices/system/cpu/online
printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

Signed-off-by: ldts <jramirez@baylibre.com>

show more ...

ti: k3: common: Do not disable cache on TI K3 core powerdown

Leave the caches on and explicitly flush any data that
may be stale when the core is powered down. This prevents
non-coherent interconnec

ti: k3: common: Do not disable cache on TI K3 core powerdown

Leave the caches on and explicitly flush any data that
may be stale when the core is powered down. This prevents
non-coherent interconnect access which has negative side-
effects on AM65x.

Signed-off-by: Andrew F. Davis <afd@ti.com>

show more ...

scmi: Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled

When HW_ASSISTED_COHERENCY is enabled we can use spinlocks
instead of using the more complex and slower bakery algorithm.

Change-Id

scmi: Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled

When HW_ASSISTED_COHERENCY is enabled we can use spinlocks
instead of using the more complex and slower bakery algorithm.

Change-Id: I9d791a70050d599241169b9160a67e57d5506564
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

show more ...