Merge pull request #1386 from soby-mathew/sm/dyn_bl31

Extend dynamic configuration

Merge pull request #1393 from geesun/correct_comment

Correct some typo errors in comment

Correct some typo errors in comment

File: include/common/aarch64/el3_common_macros.S

Change-Id: I619401e961a3f627ad8864781b5f90bc747c3ddb
Signed-off-by: Qixiang Xu <qixiang.xu@arm.com>

FVP: Add dummy configs for BL31, BL32 and BL33

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined

FVP: Add dummy configs for BL31, BL32 and BL33

This patch adds soc_fw_config, tos_fw_config and nt_fw_config to the FVP.
The config files are placeholders and do not have any useful bindings
defined. The tos_fw_config is packaged in FIP and loaded by BL2 only
if SPD=tspd. The load address of these configs are specified in tb_fw_config
via new bindings defined for these configs. Currently, in FVP, the
soc_fw_config and tos_fw_config is loaded in the page between BL2_BASE
and ARM_SHARED_RAM. This memory was typically used for BL32 when
ARM_TSP_RAM_LOCATION=tsram but since we cannot fit BL32 in that
space anymore, it should be safe to use this memory for these configs.
There is also a runtime check in arm_bl2_dyn_cfg_init() which ensures
that this overlap doesn't happen.

The previous arm_dyn_get_hwconfig_info() is modified to accept configs
other than hw_config and hence renamed to arm_dyn_get_config_load_info().
The patch also corrects the definition of ARM_TB_FW_CONFIG_LIMIT to be
BL2_BASE.

Change-Id: I03a137d9fa1f92c862c254be808b8330cfd17a5a
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

Dynamic cfg: Enable support on CoT for other configs

This patch implements support for adding dynamic configurations for
BL31 (soc_fw_config), BL32 (tos_fw_config) and BL33 (nt_fw_config). The
neces

Dynamic cfg: Enable support on CoT for other configs

This patch implements support for adding dynamic configurations for
BL31 (soc_fw_config), BL32 (tos_fw_config) and BL33 (nt_fw_config). The
necessary cert tool support and changes to default chain of trust are made
for these configs.

Change-Id: I25f266277b5b5501a196d2f2f79639d838794518
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

FVP: Enable capability to disable auth via dynamic config

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 pa

FVP: Enable capability to disable auth via dynamic config

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

Allow disabling authentication dynamically

This patch allows platforms to dynamically disable authentication of
images during cold boot. This capability is controlled via the
DYN_DISABLE_AUTH build

Allow disabling authentication dynamically

This patch allows platforms to dynamically disable authentication of
images during cold boot. This capability is controlled via the
DYN_DISABLE_AUTH build flag and is only meant for development
purposes.

Change-Id: Ia3df8f898824319bb76d5cc855b5ad6c3d227260
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

show more ...

Ensure read and write of flags are 32 bit

In 'console_set_scope' and when registering a console, field 'flags' of
'console_t' is assigned a 32-bit value. However, when it is actually
used, the funct

Ensure read and write of flags are 32 bit

In 'console_set_scope' and when registering a console, field 'flags' of
'console_t' is assigned a 32-bit value. However, when it is actually
used, the functions perform 64-bit reads to access its value. This patch
changes all 64-bit reads to 32-bit reads.

Change-Id: I181349371409e60065335f078857946fa3c32dc1
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

show more ...

Merge pull request #1380 from CJKay/mmap-fix

Fix incorrect number of reserved memory map entries for Arm platforms

Merge pull request #1379 from CJKay/nsram-fix

Fix incorrect NSRAM memory map region for SGI-575

Merge pull request #1373 from jeenu-arm/ras-support

RAS support

Revert "plat/arm: Migrate AArch64 port to the multi console driver"

This reverts commit 2f18aa1fa35305f8feec25867473d30975b242fe.

It is causing some tests to fail. Until the cause is found and fixe

Revert "plat/arm: Migrate AArch64 port to the multi console driver"

This reverts commit 2f18aa1fa35305f8feec25867473d30975b242fe.

It is causing some tests to fail. Until the cause is found and fixed, it
is needed to remove this commit from master.

Change-Id: Ic5ff7a841903a15613e00379e87cbbd8a0e85152
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

css: Do not map the non-secure RAM as secure

Change-Id: I7e73c0ab134da11c49f990b739245110c59eac2b
Signed-off-by: Chris Kay <chris.kay@arm.com>

css: Fix erroneous non-secure RAM base address/size for SGI-575

SGI-575's NSRAM is neither in the same place nor the same size as Juno's.

Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed

css: Fix erroneous non-secure RAM base address/size for SGI-575

SGI-575's NSRAM is neither in the same place nor the same size as Juno's.

Change-Id: Id6d692e9c7e9c1360014bb525eda966ebe29c823
Signed-off-by: Chris Kay <chris.kay@arm.com>

show more ...

plat/arm: Fix incorrect bounds check in ARM_CASSERT_MMAP

The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
addi

plat/arm: Fix incorrect bounds check in ARM_CASSERT_MMAP

The bounds check in ARM_CASSERT_MMAP does not take into account the
array sentinel in plat_arm_mmap. This commit fixes this, and adds an
additional check to ensure the number of entries in the array is
within the bounds of PLAT_ARM_MMAP_ENTRIES.

Change-Id: Ie6df10c0aa0890d62826bc3224ad7b3e36fd53e2
Signed-off-by: Chris Kay <chris.kay@arm.com>

show more ...

plat/arm: Fix incorrect number of reserved memory map entries

There are three calls to mmap_add_region() that always occur in
arm_setup_page_tables(), and two further calls based on whether coherent

plat/arm: Fix incorrect number of reserved memory map entries

There are three calls to mmap_add_region() that always occur in
arm_setup_page_tables(), and two further calls based on whether coherent
memory is enabled, and whether SPM is enabled in BL31.

This commit adapts the ARM_BL_REGIONS definition to match the number of
calls made inside arm_setup_page_tables() so that the MAX_MMAP_REGIONS
is realigned with what is actually occurring.

Change-Id: I7adc05951abccf2cbd5c86280eb874911e6a1566
Signed-off-by: Chris Kay <chris.kay@arm.com>

show more ...

plat/arm: Migrate AArch64 port to the multi console driver

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. Ho

plat/arm: Migrate AArch64 port to the multi console driver

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size of BL31 has been increased in builds with SPM.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

multi console: Assert that consoles aren't registered twice

In the multi console driver, allowing to register the same console more
than once may result in an infinte loop when putc is called.

If,

multi console: Assert that consoles aren't registered twice

In the multi console driver, allowing to register the same console more
than once may result in an infinte loop when putc is called.

If, for example, a boot message is trying to be printed, but the
consoles in the loop in the linked list are runtime consoles, putc will
iterate forever looking for a console that can print boot messages (or
a NULL pointer that will never come).

This loop in the linked list can occur after restoring the system from a
system suspend. The boot console is registered during the cold boot in
BL31, but the runtime console is registered even in the warm boot path.
Consoles are always added to the start of the linked list when they are
registered, so this it what should happen if they were actually
different structures:

console_list -> NULL
console_list -> BOOT -> NULL
console_list -> RUNTIME -> BOOT -> NULL
console_list -> RUNTIME -> RUNTIME -> BOOT -> NULL

In practice, the two runtime consoles are the same one, so they create
this loop:

console_list -> RUNTIME -. X -> BOOT -> NULL
^ |
`----'

This patch adds an assertion to detect this problem. The assertion will
fail whenever the same structure tries to be registered while being on
the list.

In order to assert this, console_is_registered() has been implemented.
It returns 1 if the specified console is registered, 0 if not.

Change-Id: I922485e743775ca9bd1af9cbd491ddd360526a6d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

Merge pull request #1377 from robertovargas-arm/compiler-warnings

Compiler warnings

xlat: Fix warning in CHECK_VIRT_ADDR_SPACE_SIZE

When TF is compiled for aarch32 MAX_VIRT_ADDR_SPACE_SIZE is 2^32 in some cases,
which makes the test (size) <= MAX_VIRT_ADDR_SPACE_SIZE a tautology be

xlat: Fix warning in CHECK_VIRT_ADDR_SPACE_SIZE

When TF is compiled for aarch32 MAX_VIRT_ADDR_SPACE_SIZE is 2^32 in some cases,
which makes the test (size) <= MAX_VIRT_ADDR_SPACE_SIZE a tautology because
uintptr_t is a 32 bit value. The cast remove the warning for clang.

Change-Id: I1345f3400f8fbbe4ffd3caa990a90e7ba593dba5
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

show more ...

Merge pull request #1354 from robertovargas-arm/mem_protect

ARM platforms: Demonstrate mem_protect from el3_runtime

ARM Platforms: Support RAS

- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.

- Call the common RAS initialisation from ARM BL31 setup.

- Add empty d

ARM Platforms: Support RAS

- Assign 0x10 for RAS exceptions on ARM platforms, and install
EHF priority descriptor.

- Call the common RAS initialisation from ARM BL31 setup.

- Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

RAS: Add fault injection support

The ARMv8.4 RAS extensions introduce architectural support for software
to inject faults into the system in order to test fault-handling
software. This patch introdu

RAS: Add fault injection support

The ARMv8.4 RAS extensions introduce architectural support for software
to inject faults into the system in order to test fault-handling
software. This patch introduces the build option FAULT_HANDLING_SUPPORT
to allow for lower ELs to use registers in the Standard Error Record to
inject fault. The build option RAS_EXTENSIONS must also be enabled along
with fault injection.

This feature is intended for testing purposes only, and is advisable to
keep disabled for production images.

Change-Id: I6f7a4454b15aec098f9505a10eb188c2f928f7ea
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

RAS: Allow individual interrupt registration

EHF currently allows for registering interrupt handlers for a defined
priority ranges. This is primarily targeted at various EL3 dispatchers
to own range

RAS: Allow individual interrupt registration

EHF currently allows for registering interrupt handlers for a defined
priority ranges. This is primarily targeted at various EL3 dispatchers
to own ranges of secure interrupt priorities in order to delegate
execution to lower ELs.

The RAS support added by earlier patches necessitates registering
handlers based on interrupt number so that error handling agents shall
receive and handle specific Error Recovery or Fault Handling interrupts
at EL3.

This patch introduces a macro, RAS_INTERRUPTS() to declare an array of
interrupt numbers and handlers. Error handling agents can use this macro
to register handlers for individual RAS interrupts. The array is
expected to be sorted in the increasing order of interrupt numbers.

As part of RAS initialisation, the list of all RAS interrupts are sorted
based on their ID so that, given an interrupt, its handler can be looked
up with a simple binary search.

For an error handling agent that wants to handle a RAS interrupt,
platform must:

- Define PLAT_RAS_PRI to be the priority of all RAS exceptions.

- Enumerate interrupts to have the GIC driver program individual EL3
interrupts to the required priority range. This is required by EHF
even before this patch.

Documentation to follow.

Change-Id: I9471e4887ff541f8a7a63309e9cd8f771f76aeda
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...

RAS: Add support for node registration

Previous patches added frameworks for handling RAS errors. This patch
introduces features that the platform can use to enumerate and iterate
RAS nodes:

- Th

RAS: Add support for node registration

Previous patches added frameworks for handling RAS errors. This patch
introduces features that the platform can use to enumerate and iterate
RAS nodes:

- The REGISTER_RAS_NODES() can be used to expose an array of
ras_node_info_t structures. Each ras_node_info_t describes a RAS
node, along with handlers for probing the node for error, and if
did record an error, another handler to handle it.

- The macro for_each_ras_node() can be used to iterate over the
registered RAS nodes, probe for, and handle any errors.

The common platform EA handler has been amended using error handling
primitives introduced by both this and previous patches.

Change-Id: I2e13f65a88357bc48cd97d608db6c541fad73853
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

show more ...