stpmic1: fix boot-on minimal voltage

Change stpmic1_bo_voltage_cfg() to highlight voltage argument is
a minimal desired boot-on voltage requirement, not an absolute
voltage requested at boot-on, as

stpmic1: fix boot-on minimal voltage

Change stpmic1_bo_voltage_cfg() to highlight voltage argument is
a minimal desired boot-on voltage requirement, not an absolute
voltage requested at boot-on, as per DT binding property .

stpmic1_bo_voltage_unpg() that applies boot-on voltage is updated
to not lower current voltage if above min voltage constraint.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: relax PMIC control API functions

Return an error if requested to save Low Power regulator data
if there is no Low Power control defined. This changes
stpmic1_lp_cfg(), stpmic1_lp_reg_on_off

stpmic1: relax PMIC control API functions

Return an error if requested to save Low Power regulator data
if there is no Low Power control defined. This changes
stpmic1_lp_cfg(), stpmic1_lp_reg_on_off() and stpmic1_lp_copy_reg()
to return with a error if regulator does not support Low Power config.

Add helper function to stpmic1_regu_has_lp_cfg() to return if a
regulator defines Low Power configuration.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: add stpmic1_bo_enable_cfg() to save boot-on config

Add a helper stpmic1_bo_enable_cfg() to save the minimal regulator
data needed to operate at least the boot-on constraint: control on
enab

stpmic1: add stpmic1_bo_enable_cfg() to save boot-on config

Add a helper stpmic1_bo_enable_cfg() to save the minimal regulator
data needed to operate at least the boot-on constraint: control on
enable/disable support: control register offset and bit position.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: describe 5V fixed regulators

Describe regulators boost, pwr_sw1 and pwr_sw2 that are gated 5V fixed
regulators.

These regulators have not reset mask support hence change
stpmic1_regulator_

stpmic1: describe 5V fixed regulators

Describe regulators boost, pwr_sw1 and pwr_sw2 that are gated 5V fixed
regulators.

These regulators have not reset mask support hence change
stpmic1_regulator_mask_reset_set() to fail accordingly.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: refine resources helper macros

Define bit fields in position xxx_POS rather than in bit mask.
Use BIT() and GENMASK_32() rather than numerical values.

Signed-off-by: Etienne Carriere <etie

stpmic1: refine resources helper macros

Define bit fields in position xxx_POS rather than in bit mask.
Use BIT() and GENMASK_32() rather than numerical values.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: save enable bit position in regulator control

Add enable bit position info in STPMIC1 regulators description
instead of assuming it is BIT(0). This allows to define other
regulators with en

stpmic1: save enable bit position in regulator control

Add enable bit position info in STPMIC1 regulators description
instead of assuming it is BIT(0). This allows to define other
regulators with enable bit not at position 0.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stpmic1: stpmic1_is_regulator_enabled() returns a boolean

Change helper function stpmic1_is_regulator_enabled() to return
a boolean value.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.o

stpmic1: stpmic1_is_regulator_enabled() returns a boolean

Change helper function stpmic1_is_regulator_enabled() to return
a boolean value.

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

stm32_bsec: introduce configuration switch for write support

Introduce configuration switch CFG_STM32_BSEC_WRITE to not embed
write operation support in BSEC.

Signed-off-by: Etienne Carriere <etien

stm32_bsec: introduce configuration switch for write support

Introduce configuration switch CFG_STM32_BSEC_WRITE to not embed
write operation support in BSEC.

Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

stm32_bsec: simplify lock support functions

Change stm32_bsec_otp_lock() to only lock fuses as hardware safely does
not allow unlocking a locked BSEC word.

Functions to read a lock return a TEE_Res

stm32_bsec: simplify lock support functions

Change stm32_bsec_otp_lock() to only lock fuses as hardware safely does
not allow unlocking a locked BSEC word.

Functions to read a lock return a TEE_Result status aside from the
effective lock value read.

Rename stm32_bsec_wr_lock() into stm32_bsec_read_permanent_lock()
as it is more explicit.

Change IMSG() into DMSG() as traces refer to debug info rather than
informative info.

Use flag character '#' to prefix printed hexadecimal values with "0x".

Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers/scmi-msg: smt entry points for incoming messages

This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
t

drivers/scmi-msg: smt entry points for incoming messages

This change implements SCMI channels for reading a SCMI message from a
shared memory and call the SCMI message drivers to route the message
to the target platform services.

SMT refers to the shared memory management protocol which is used
to get/put message/response in shared memory. SMT is a 28byte header
stating shared memory state and exchanged protocol data.

The processing entry for a SCMI message can be a secure interrupt
(CFG_SCMI_MSG_SMT_INTERRUPT_ENTRY=y), and fastcall SMC
(CFG_SCMI_MSG_SMT_FASTCALL_ENTRY=y) or a threaded execution
context entry (CFG_SCMI_MSG_SMT_THREAD_ENTRY=y).

SMT description in this implementation is based on the SCP-firmware
implementation [1].

Link: [1] https://github.com/ARM-software/SCP-firmware.git

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers/scmi-msg: support for reset domain protocol

Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the

drivers/scmi-msg: support for reset domain protocol

Adds SCMI reset domain protocol support in the SCMI message drivers
as defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.

Embedded upon CFG_SCMI_MSG_RESET_DOMAIN=y.

scmi_msg_get_rd_handler() sanitizes the message_id value
against any speculative use of reset domain ID as a index since by
SCMI specification, IDs are indices.

SCMI resource in this implementation are dumped or inspired by the
SCP-firmware implementation [2] of the SCMI protocol, server side.

Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] https://github.com/ARM-software/SCP-firmware.git

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers/scmi-msg: support for clock protocol

Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification

drivers/scmi-msg: support for clock protocol

Adds SCMI clock protocol support in the SCMI message drivers as
defined in SCMI specification v2.0 [1]. Not all the messages
defined in the specification are supported.

Embedded upon CFG_SCMI_MSG_CLOCK=y.

Platform can provide one of the plat_scmi_clock_*() handler for the
supported operations set/get state/rate and others.

scmi_msg_get_clock_handler() sanitizes the message_id value
against any speculative use of clock ID as a index since by
SCMI specification, IDs are indices.

SCMI resource in this implementation are dumped or inspired by the
SCP-firmware implementation [2] of the SCMI protocol, server side.

Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] https://github.com/ARM-software/SCP-firmware.git

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers/scmi-msg: driver for processing scmi messages

This change introduces drivers to allow a platform to create a SCMI
service and register handlers for client request (SCMI agent) on
system reso

drivers/scmi-msg: driver for processing scmi messages

This change introduces drivers to allow a platform to create a SCMI
service and register handlers for client request (SCMI agent) on
system resources. This is the first piece of the drivers: an entry
function, the SCMI base protocol support and helpers for create
the response message.

With this change, scmi_process_message() is the entry function to
process an incoming SCMI message. The function expect the message
is already copied from shared memory into secure memory. The message
structure stores message reference and output buffer reference where
response message shall be stored.

scmi_process_message() calls the SCMI protocol driver according to
the protocol ID in the message. The SCMI protocol driver will call
defined platform handlers according to the message content.

This change introduces only the SCMI base protocol as defined in
SCMI specification v2.0 [1]. Not all the messages defined
in the specification are supported.

SCMI resource in this implementation are dumped or inspired by the
SCP-firmware implementation [2] of the SCMI protocol, server side.

Link: [1] http://infocenter.arm.com/help/topic/com.arm.doc.den0056a/DEN0056A_System_Control_and_Management_Interface.pdf
Link: [2] https://github.com/ARM-software/SCP-firmware.git

Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

imx: snvs: rework snvs driver

Remove the unused SRTC functionality which is not wired up anywhere.
Instead add a function to read the device configuration and system
security monitor instead.

Signe

imx: snvs: rework snvs driver

Remove the unused SRTC functionality which is not wired up anywhere.
Instead add a function to read the device configuration and system
security monitor instead.

Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Cedric Neveux <cedric.neveux@nxp.com>

show more ...

tzc380: add function to lockdown regions

The TZC380 allows a lockdown of the region configuration to prevent
unintended or malicious configuration changes. Add a function which
locks down all region

tzc380: add function to lockdown regions

The TZC380 allows a lockdown of the region configuration to prevent
unintended or malicious configuration changes. Add a function which
locks down all regions of the current configuration

Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Reviewed-by: Clement Faure <clement.faure@nxp.com>

show more ...

drivers: tzc: set maximum region size for tzc_auto_configure()

According to the TZC380 documentation, the AXI address width controls
the upper limit value of the region size.
This fix makes sure tha

drivers: tzc: set maximum region size for tzc_auto_configure()

According to the TZC380 documentation, the AXI address width controls
the upper limit value of the region size.
This fix makes sure that tzc_auto_configure() function will not
allocated a region bigger that the AXI address width.

Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>

show more ...

plat-amlogic: Add initial support for Amlogic platforms

This is the initial support for the Amlogic platforms.

Tested 64-bin mode on A113D (AXG) board using upstream TF-A BL31.

* xtest results (-l

plat-amlogic: Add initial support for Amlogic platforms

This is the initial support for the Amlogic platforms.

Tested 64-bin mode on A113D (AXG) board using upstream TF-A BL31.

* xtest results (-l 15):
| 44074 subtests of which 0 failed
| 96 test cases of which 0 failed
| 0 test cases were skipped
| TEE test application done!

* Compiled with:
| make PLATFORM=amlogic

Reviewed-by: Jerome Forissier <jerome@forissier.org>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>

show more ...

drivers: Add func to config gpio pin for secure access

Add func to config gpio pin for secure access

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Acked-by: Jerome Forissier <jero

drivers: Add func to config gpio pin for secure access

Add func to config gpio pin for secure access

Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

drivers: bnxt: Add driver support for additional bnxt cmds

Add driver support for following bnxt commands:
- HEALTH_STATUS
- HANDSHAKE_STATUS
- CRASH_DUMP_COPY

Signed-off-by: Vikas Gupta <vikas.

drivers: bnxt: Add driver support for additional bnxt cmds

Add driver support for following bnxt commands:
- HEALTH_STATUS
- HANDSHAKE_STATUS
- CRASH_DUMP_COPY

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

drivers: bnxt: Load bnxt images from secure memory

Load bnxt images from the secure memory at 1K offset,
If found on the secure memory instead of flash.
We copy the images from flash to secure memor

drivers: bnxt: Load bnxt images from secure memory

Load bnxt images from the secure memory at 1K offset,
If found on the secure memory instead of flash.
We copy the images from flash to secure memory for
the very first time

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Acked-by: Jerome Forissier <jerome@forissier.org>

show more ...

drivers: gic: Add GIC_SPI/SGI/PPI helper macros

Add GIC_SPI/SGI/PPI helper macros

Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tiga

drivers: gic: Add GIC_SPI/SGI/PPI helper macros

Add GIC_SPI/SGI/PPI helper macros

Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Reviewed-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers: bnxt: add Broadcom bnxt driver

Add Broadcom bnxt driver which helps to load the
firmware on bnxt device

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sheetal Tigadol

drivers: bnxt: add Broadcom bnxt driver

Add Broadcom bnxt driver which helps to load the
firmware on bnxt device

Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Sheetal Tigadoli <sheetal.tigadoli@broadcom.com>
Reviewed-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Acked-by: Jerome Forissier <jerome@forissier.org>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

Get rid of option -Wno-suggest-attribute=noreturn

The GCC option -Wno-suggest-attribute=noreturn is not supported by
Clang. Instead of playing with compiler options, let's fix the code
according to

Get rid of option -Wno-suggest-attribute=noreturn

The GCC option -Wno-suggest-attribute=noreturn is not supported by
Clang. Instead of playing with compiler options, let's fix the code
according to the following rules:
- If a function is know to never return, it should have the __noreturn
attribute in the header file.
- If only some implementation of a function never returns, __noreturn
shall be applied to that particular implementation in the .c file.

Signed-off-by: Jerome Forissier <jerome@forissier.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>

show more ...

drivers: imx_wdog: update wdog support for mx7ulp

Update watchdog for imx7ulp SoC support.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>

drivers: wdt: Add arm SP805 watchdog driver

Add sp805 watchdog driver with following functionality:
- start/reload watchdog with specified timeout
- stop watchdog
- ping watchdog (clear watchdog int

drivers: wdt: Add arm SP805 watchdog driver

Add sp805 watchdog driver with following functionality:
- start/reload watchdog with specified timeout
- stop watchdog
- ping watchdog (clear watchdog interrupt and reload it)
- register watchdog interrupt handler

Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>

show more ...