| /rk3399_rockchip-uboot/board/freescale/mpc832xemds/ |
| H A D | README | 102 1)Make sure the DIP SW support PCI mode as described in Section 1.1.
104 2)To Make U-Boot image support PCI 33MHz, use
105 Make MPC832XEMDS_HOST_33_config
107 3)To Make U-Boot image support PCI 66MHz, use
108 Make MPC832XEMDS_HOST_66M_config
|
| /rk3399_rockchip-uboot/doc/uImage.FIT/ |
| H A D | update_uboot.its | 3 * Make sure the flashing addresses ('load' prop) is correct for your board!
|
| H A D | signature.txt | 413 Make sure p11-kit, opensc are installed and that p11-kit is setup to use opensc.
442 Make off-card backup of encryption key? (Y/n) n
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | README.arm-caches | 8 - Make sure CONFIG_SYS_ICACHE_OFF is not set and call icache_enable().
11 - Make sure CONFIG_SYS_DCACHE_OFF is not set and call dcache_enable().
|
| H A D | README.silent | 21 suppressed automatically. Make sure to enable "nulldev" by
|
| H A D | README.mpc83xx.ddrecc | 64 4. Make sure used memory region got re-initialized with 0x0123456789abcdef
104 4. Make sure used memory region got re-initialized with 0x0123456789abcdef
|
| H A D | README.fdt-overlays | 76 overlay. Make sure you have enough space to grow the base tree without
|
| H A D | README.sdp | 47 U-Boot configurations CONFIG_G_DNL_(VENDOR|PRODUCT)_NUM. Make sure
|
| H A D | README.chromium | 101 Reboot the device in dev mode. Make sure that you have USB booting enabled. To
193 Reboot the device in dev mode. Make sure that you have USB booting enabled. To
|
| H A D | README.ramboot-ppc85xx | 79 There can be added specific Make options for RAMBoot. We can keep different
|
| H A D | README.kconfig | 112 [2] Make sure to define necessary CONFIG_SYS_* in Kconfig:
|
| /rk3399_rockchip-uboot/tools/buildman/ |
| H A D | builderthread.py | 91 def Make(self, commit, brd, stage, cwd, *args, **kwargs): member in BuilderThread
227 result = self.Make(commit, brd, 'mrproper', cwd,
230 result = self.Make(commit, brd, 'config', cwd,
237 result = self.Make(commit, brd, 'build', cwd, *args,
|
| H A D | test.py | 140 def Make(self, commit, brd, stage, *args, **kwargs): member in TestBuild
189 build.do_make = self.Make
|
| H A D | builder.py | 245 self.do_make = self.Make
380 def Make(self, commit, brd, stage, cwd, *args, **kwargs): member in Builder
|
| /rk3399_rockchip-uboot/arch/arm/dts/ |
| H A D | bcm2836.dtsi | 70 /* Make the BCM2835-style global interrupt controller be a child of the
|
| H A D | bcm2837.dtsi | 68 /* Make the BCM2835-style global interrupt controller be a child of the
|
| H A D | sun8i-a33-ga10h-v1.1.dts | 52 /* Make u-boot set mac-address for rtl8703as (no eeprom) */
|
| H A D | rk3288-veyron-jerry.dts | 147 /* Make sure eMMC is not in reset */
|
| H A D | sun8i-q8-common.dtsi | 48 /* Make u-boot set mac-address for wifi without an eeprom */
|
| /rk3399_rockchip-uboot/arch/powerpc/cpu/mpc85xx/ |
| H A D | u-boot-spl.lds | 100 * Make sure that the bss segment isn't linked at 0x0, otherwise its
|
| H A D | u-boot.lds | 106 * Make sure that the bss segment isn't linked at 0x0, otherwise its
|
| /rk3399_rockchip-uboot/board/boundary/nitrogen6x/ |
| H A D | README.mx6qsabrelite | 34 the board). Make sure SW1 switch is at position "00", so that it can boot
|
| /rk3399_rockchip-uboot/drivers/mtd/ubi/ |
| H A D | Kconfig | 7 Make the verbose messages from UBI stop printing. This leaves
|
| /rk3399_rockchip-uboot/doc/SPL/ |
| H A D | README.am335x-network | 39 /etc/default/dhcpd or /etc/default/isc-dhcp-server). Make sure there
|
| /rk3399_rockchip-uboot/board/hisilicon/poplar/ |
| H A D | README | 94 Make sure you are using the correct branch on each one of these repositories.
|