| /OK3568_Linux_fs/u-boot/doc/device-tree-bindings/adc/ |
| H A D | adc.txt | 3 There are no mandatory properties for ADC. However, if Voltage info is required,
6 - use regulator phandle to enable/read supply's Voltage
9 *optional and always checked, Voltage polarity info:
10 - vdd-polarity-negative: positive reference Voltage has a negative polarity
11 - vss-polarity-negative: negative reference Voltage has a negative polarity
15 *optional and always checked, supply Voltage constants:
20 - vdd-microvolts: positive reference Voltage value [uV]
21 - vss-microvolts: negative reference Voltage value [uV]
|
| /OK3568_Linux_fs/kernel/Documentation/hwmon/ |
| H A D | ucd9200.rst | 63 in1_min Minimum Voltage. From VIN_UV_WARN_LIMIT register.
65 in1_lcrit Critical minimum Voltage. VIN_UV_FAULT_LIMIT register.
68 in1_min_alarm Voltage low alarm. From VIN_UV_WARNING status.
69 in1_max_alarm Voltage high alarm. From VIN_OV_WARNING status.
70 in1_lcrit_alarm Voltage critical low alarm. From VIN_UV_FAULT status.
71 in1_crit_alarm Voltage critical high alarm. From VIN_OV_FAULT status.
75 in[2-5]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register.
77 in[2-5]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register.
80 in[2-5]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
81 in[2-5]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
[all …]
|
| H A D | intel-m10-bmc-hwmon.rst | 57 in0_label "QSFP0 Supply Voltage"
58 in1_label "QSFP1 Supply Voltage"
59 in2_label "FPGA Core Voltage"
60 in3_label "12V Backplane Voltage"
61 in4_label "1.2V Voltage"
62 in5_label "12V AUX Voltage"
63 in6_label "1.8V Voltage"
64 in7_label "3.3V Voltage"
|
| H A D | max16064.rst | 21 Controller with Active-Voltage Output Control and PMBus Interface.
50 in[1-4]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register.
52 in[1-4]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register.
55 in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
56 in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
57 in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT
59 in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT
|
| H A D | mc13783-adc.rst | 47 0 Battery Voltage (BATT) 2.50 - 4.65V -2.40V
50 3 Charger Voltage (CHRGRAW) 0 - 10V / /5
54 6 General Purpose ADIN6 / Backup Voltage (LICELL) 0 - 2.30V / No /
73 0 Battery Voltage (BATT) 0 - 4.8V /2
76 3 Charger Voltage (CHRGRAW) 0 - 12V / /5
81 6 General Purpose ADIN6 / Backup Voltage (LICELL) 0 - 2.4V / No
82 Backup Voltage (LICELL) 0 - 3.6V x2/3
|
| H A D | max34440.rst | 46 PMBus 12-Channel Voltage Monitor & Sequencer
56 PMBus 16-Channel Voltage Monitor & Sequencer
73 It also supports the MAX34451, MAX34460, and MAX34461 PMBus Voltage Monitor &
90 voltage measurement is enabled for a given channel. Voltage measurement is
115 in[1-6]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register.
117 in[1-6]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register.
120 in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
121 in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
122 in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT
124 in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT
|
| H A D | max8688.rst | 50 in1_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register.
52 in1_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register.
55 in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
56 in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
57 in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT
59 in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT
|
| H A D | adm1266.rst | 34 inX_min Minimum Voltage.
36 inX_min_alarm Voltage low alarm.
37 inX_max_alarm Voltage high alarm.
|
| H A D | ltc4151.rst | 22 The LTC4151 is a High Voltage I2C Current and Voltage Monitor.
42 Voltage readings provided by this driver are reported as obtained from the ADIN
|
| H A D | corsair-cpro.rst | 30 in0_input Voltage on SATA 12v
31 in1_input Voltage on SATA 5v
32 in2_input Voltage on SATA 3.3v
|
| H A D | ucd9000.rst | 95 in[1-12]_min Minimum Voltage. From VOUT_UV_WARN_LIMIT register.
97 in[1-12]_lcrit Critical minimum Voltage. VOUT_UV_FAULT_LIMIT register.
100 in[1-12]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
101 in[1-12]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
102 in[1-12]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT
104 in[1-12]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT
|
| H A D | ltc2990.rst | 26 LTC2990 is a Quad I2C Voltage, Current and Temperature Monitor.
44 in0_input Voltage at Vcc pin in millivolt (range 2.5V to 5V)
52 in[1-4]_input Voltage at V[1-4] pin in millivolt
|
| H A D | pmbus.rst | 198 inX_min Minimum Voltage.
202 inX_lcrit Critical minimum Voltage.
206 inX_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status.
207 inX_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status.
208 inX_lcrit_alarm Voltage critical low alarm.
210 inX_crit_alarm Voltage critical high alarm.
|
| H A D | bt1-pvt.rst | 59 Voltage Monitoring
106 in[0-3]_label RO CPU Voltage sensor (either core or
111 in[0-3]_min_alarm RO Voltage input alarm. Returns 1 if
114 in[0-3]_max_alarm RO Voltage input alarm. Returns 1 if
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/regulator/ |
| H A D | pwm-regulator.txt | 6 Voltage Table: When in this mode, a voltage table (See below) of
16 Continuous Voltage: This mode uses the regulator's maximum and minimum
32 Only required for Voltage Table Mode:
33 - voltage-table: Voltage and Duty-Cycle table consisting of 2 cells
50 in Voltage Table Mode. If no voltage-table is provided, then the device will
51 be used in Continuous Voltage Mode.
60 Continuous Voltage With Enable GPIO Example:
77 Voltage Table Example:
85 /* Voltage Duty-Cycle */
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/display/bridge/ |
| H A D | sii9234.txt | 6 - avcc33-supply : MHL/USB Switch Supply Voltage (3.3V)
7 - iovcc18-supply : I/O Supply Voltage (1.8V)
8 - avcc12-supply : TMDS Analog Supply Voltage (1.2V)
9 - cvcc12-supply : Digital Core Supply Voltage (1.2V)
|
| H A D | sil-sii8620.txt | 6 - cvcc10-supply: Digital Core Supply Voltage (1.0V)
7 - iovcc18-supply: I/O Supply Voltage (1.8V)
|
| /OK3568_Linux_fs/u-boot/arch/arm/mach-omap2/omap5/ |
| H A D | Kconfig | 56 3: Voltage ramp time, which can be derived using the PMIC slew rate
60 menu "Voltage Domain OPP selections"
63 prompt "MPU Voltage Domain"
78 prompt "DSPEVE Voltage Domain"
102 prompt "IVA Voltage Domain"
126 prompt "GPU Voltage Domain"
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/hwmon/ |
| H A D | ltc4151.txt | 1 LTC4151 High Voltage I2C Current and Voltage Monitor
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/power/supply/ |
| H A D | max17042_battery.txt | 22 - maxim,dead-volt : Voltage threshold to report battery
24 - maxim,over-volt : Voltage threshold to report battery
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/input/ |
| H A D | adc-keys.txt | 8 - keyup-threshold-microvolt: Voltage at which all the keys are considered up.
20 - press-threshold-microvolt: Voltage ADC input when this key is pressed.
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/sound/ |
| H A D | da7213.txt | 13 - dlg,micbias1-lvl : Voltage (mV) for Mic Bias 1
15 - dlg,micbias2-lvl : Voltage (mV) for Mic Bias 2
|
| H A D | tas2552.txt | 12 "iovdd" I/O Voltage
13 "avdd" Analog DAC Voltage
|
| /OK3568_Linux_fs/u-boot/doc/device-tree-bindings/regulator/ |
| H A D | sandbox.txt | 22 - regulator-min-microvolt: minimum allowed Voltage to set
23 - regulator-max-microvolt: minimum allowed Voltage to set
|
| H A D | regulator.txt | 1 Voltage/Current regulator
32 - regulator-min-microvolt: a minimum allowed Voltage value
33 - regulator-max-microvolt: a maximum allowed Voltage value
|