| /OK3568_Linux_fs/kernel/arch/sh/kernel/cpu/sh4a/ |
| H A D | setup-shx3.c | 185 GPIO0, GPIO1, GPIO2, GPIO3, enumerator
233 INTC_VECT(GPIO2, 0xe80), INTC_VECT(GPIO3, 0xea0),
267 DU, GPIO3, GPIO2, GPIO1, GPIO0, PAM, 0, 0,
302 { 0xfe410810, 0, 32, 4, /* INT2PRI4 */ { 0, 0, PAM, GPIO3,
|
| /OK3568_Linux_fs/kernel/drivers/pinctrl/ |
| H A D | pinctrl-xway.c | 119 MFP_XWAY(GPIO3, GPIO, CGU, NONE, PCI),
226 static const unsigned pins_clkout2[] = {GPIO3};
235 static const unsigned pins_pci_req3[] = {GPIO3};
355 MFP_XWAY(GPIO3, GPIO, STP, EPHY, EBU),
394 static const unsigned ase_pins_stp[] = {GPIO1, GPIO2, GPIO3};
397 static const unsigned ase_pins_ephy_led1[] = {GPIO3};
483 MFP_XWAY(GPIO3, GPIO, CGU, SDIO, PCI),
557 static const unsigned danube_pins_clkout2[] = {GPIO3};
565 static const unsigned danube_pins_pci_req3[] = {GPIO3};
658 MFP_XWAY(GPIO3, GPIO, CGU, SDIO, PCI),
[all …]
|
| H A D | pinctrl-lantiq.h | 109 GPIO3, enumerator
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/sound/ |
| H A D | rt5640.txt | 28 2: using GPIO3 pin as dmic1 data pin
42 5: Use GPIO3 for jack-detect
|
| H A D | rt5668.txt | 22 1: using GPIO3 pin as dmic1 clock pin
|
| H A D | rt5677.txt | 39 Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively.
|
| H A D | rt5682.txt | 22 1: using GPIO3 pin as dmic1 clock pin
|
| /OK3568_Linux_fs/kernel/drivers/media/usb/dvb-usb/ |
| H A D | dib07x0.h | 9 GPIO3 = 4, enumerator
|
| /OK3568_Linux_fs/u-boot/board/Arcturus/ucp1020/ |
| H A D | ucp1020.h | 15 #define GPIO3 28 macro
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/pinctrl/ |
| H A D | ste,nomadik.txt | 119 pins = "GPIO1", "GPIO3";
133 pins = "GPIO3";
|
| H A D | ste,abx500.txt | 51 pins = "GPIO3";
|
| /OK3568_Linux_fs/kernel/include/linux/mfd/ |
| H A D | tps65010.h | 119 #define GPIO3 3 macro
|
| /OK3568_Linux_fs/kernel/arch/arm/mach-pxa/ |
| H A D | pxa300.c | 26 MFP_ADDR_X(GPIO3, GPIO26, 0x027c),
|
| H A D | pxa930.c | 26 MFP_ADDR(GPIO3, 0x02d8),
|
| H A D | mfp-pxa300.h | 77 #define GPIO3_KP_DKIN_6 MFP_CFG_LPM(GPIO3, AF2, FLOAT)
215 #define GPIO3_MMC1_DAT0 MFP_CFG_LPM(GPIO3, AF4, DRIVE_HIGH)
440 #define GPIO3_uIO_IN MFP_CFG(GPIO3, AF1)
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/interrupt-controller/ |
| H A D | rda,8810pl-intc.txt | 32 14: GPIO3
|
| H A D | brcm,bcm2835-armctrl-ic.txt | 99 20: GPIO3
|
| /OK3568_Linux_fs/kernel/arch/arm/boot/dts/ |
| H A D | bcm2837-rpi-cm3-io3.dts | 23 "GPIO3",
|
| H A D | bcm2835-rpi-cm1-io1.dts | 23 "GPIO3",
|
| /OK3568_Linux_fs/u-boot/arch/arm/include/asm/arch-omap3/ |
| H A D | omap.h | 113 #define GPIO3 (0x1 << 3) macro
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/mfd/ |
| H A D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
46 Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
|
| H A D | as3711.txt | 33 - su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection
|
| /OK3568_Linux_fs/kernel/arch/mips/boot/dts/ralink/ |
| H A D | gardena_smart_gateway_mt7688.dts | 46 * well for GPIO3. But this is already claimed for uart1
|
| /OK3568_Linux_fs/kernel/arch/arm/mach-mmp/ |
| H A D | mfp-pxa168.h | 25 #define GPIO3_GPIO MFP_CFG(GPIO3, AF5)
150 #define GPIO3_DFI_D12 MFP_CFG(GPIO3, AF0)
|
| /OK3568_Linux_fs/kernel/arch/arm64/boot/dts/bitmain/ |
| H A D | bm1880-sophon-edge.dts | 59 "GPIO-E", /* GPIO3, LSEC pin 27 */
|