Home
last modified time | relevance | path

Searched full:drdy (Results 1 – 25 of 62) sorted by relevance

123

/OK3568_Linux_fs/kernel/arch/arm/boot/dts/
H A Dste-href-tvk1281618-r2.dtsi14 st,drdy-int-pin = <1>;
24 * cannot set its DRDY line to open drain, so it cannot be
42 * cannot set its DRDY line to open drain, so it cannot be
54 st,drdy-int-pin = <1>;
H A Dste-href-tvk1281618-r3.dtsi13 st,drdy-int-pin = <1>;
28 st,drdy-int-pin = <1>;
79 /* GPIO 32 used for DRDY, pull this down */
H A Dste-href-tvk1281618.dtsi97 * cannot set its DRDY line to open drain, so it cannot be
109 st,drdy-int-pin = <2>;
200 /* GPIO 32 used for DRDY, pull this down */
H A Dste-snowball.dts321 st,drdy-int-pin = <1>;
340 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
345 st,drdy-int-pin = <2>;
352 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
572 "GPIO166_A22", /* DRDY */
H A Dam335x-sancloud-bbe.dts117 st,drdy-int-pin = <1>;
H A Dste-href-stuib.dtsi81 st,drdy-int-pin = <1>;
/OK3568_Linux_fs/kernel/include/linux/iio/common/
H A Dst_sensors.h138 * struct st_sensor_int_drdy - ST sensor device drdy line parameters
139 * @addr: address of INT drdy register.
140 * @mask: mask to enable drdy line.
157 * struct stat_drdy - status register of DRDY (data ready) interrupt.
224 * @drdy_int_pin: Redirect DRDY on pin 1 (1) or pin 2 (2).
225 * @int_pin_open_drain: Set the interrupt/DRDY to open drain.
/OK3568_Linux_fs/kernel/drivers/iio/magnetometer/
H A Dak8974.c181 * @drdy_irq: uses the DRDY IRQ line
182 * @drdy_complete: completion for DRDY
183 * @drdy_active_low: the DRDY IRQ is active low
312 /* If we have a DRDY IRQ line, use it */ in ak8974_trigmeas()
347 "timeout waiting for DRDY IRQ\n"); in ak8974_await_drdy()
363 dev_err(&ak8974->i2c->dev, "timeout waiting for DRDY\n"); in ak8974_await_drdy()
410 /* Check if this was a DRDY from us */ in ak8974_drdy_irq_thread()
413 dev_err(&ak8974->i2c->dev, "error reading DRDY status\n"); in ak8974_drdy_irq_thread()
919 /* If we have a valid DRDY IRQ, make use of it */ in ak8974_probe()
923 dev_info(&i2c->dev, "enable rising edge DRDY IRQ\n"); in ak8974_probe()
[all …]
H A Dst_magn_core.c321 /* drdy line is routed drdy pin */
/OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/iio/magnetometer/
H A Dak8974.txt16 - interrupts: data ready (DRDY) and interrupt (INT1) lines
17 from the chip, the DRDY interrupt must be placed first.
H A Dasahi-kasei,ak8975.yaml33 AK8975 has a "Data ready" pin (DRDY) which informs that data
39 description: interrupt for DRDY pin. Triggered on rising edge.
H A Dhmc5843.txt14 - gpios : should be device tree identifier of the magnetometer DRDY pin
H A Dpni,rm3100.txt10 - interrupts: data ready (DRDY) from the chip.
/OK3568_Linux_fs/kernel/include/linux/platform_data/
H A Dst_sensors_pdata.h15 * @drdy_int_pin: Redirect DRDY on pin 1 (1) or pin 2 (2).
17 * Accelerometer DRDY on LSM330 available only on pin 1 (see datasheet).
/OK3568_Linux_fs/kernel/drivers/iio/common/st_sensors/
H A Dst_sensors_core.c279 "DRDY on pin INT%d specified, but sensor does not support interrupts\n", in st_sensors_set_drdy_int_pin()
288 "DRDY on INT1 not available.\n"); in st_sensors_set_drdy_int_pin()
296 "DRDY on INT2 not available.\n"); in st_sensors_set_drdy_int_pin()
302 dev_err(&indio_dev->dev, "DRDY on pdata not valid.\n"); in st_sensors_set_drdy_int_pin()
330 if (!device_property_read_u32(dev, "st,drdy-int-pin", &val) && (val <= 2)) in st_sensors_dev_probe()
390 /* Disable DRDY, this might be still be enabled after reboot. */ in st_sensors_init_sensor()
460 * there are some devices (e.g. LIS3MDL) where drdy line is in st_sensors_set_dataready_irq()
/OK3568_Linux_fs/kernel/drivers/iio/gyro/
H A Dst_gyro_core.c118 * for the DRDY line on INT2.
196 * for the DRDY line on INT2.
270 * for the DRDY line on INT2.
344 * for the DRDY line on INT2.
H A Dst_gyro.h29 * @drdy_int_pin: DRDY on gyros is available only on INT2 pin.
/OK3568_Linux_fs/kernel/drivers/gpu/drm/gma500/
H A Dopregion.c57 u32 drdy; /* driver readiness */ member
272 opregion->acpi->drdy = 1; in psb_intel_opregion_init()
288 opregion->acpi->drdy = 0; in psb_intel_opregion_fini()
/OK3568_Linux_fs/kernel/drivers/ide/
H A Dopti621.c74 /* DRDY is default 2 (by OPTi Databook) */ in opti621_set_pio_mode()
124 /* set address setup, DRDY timings, */ in opti621_set_pio_mode()
/OK3568_Linux_fs/kernel/arch/arm64/boot/dts/allwinner/
H A Dsun50i-a64-pinephone-1.2.dts35 * Board revision 1.2 fixed routing of the interrupt to DRDY pin,
/OK3568_Linux_fs/kernel/drivers/iio/pressure/
H A Dst_pressure.h38 * @drdy_int_pin: default press DRDY is available on INT1 pin.
/OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/iio/imu/
H A Dst_lsm6dsx.txt22 - st,drdy-int-pin: the pin on the package that will be used to signal
/OK3568_Linux_fs/kernel/drivers/iio/accel/
H A Dst_accel.h67 * @drdy_int_pin: default accel DRDY is available on INT1 pin.
/OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/iio/
H A Dst-sensors.txt16 - st,drdy-int-pin: the pin on the package that will be used to signal
/OK3568_Linux_fs/kernel/drivers/ata/
H A Dlibata-trace.c22 trace_seq_printf(p, "DRDY "); in libata_trace_parse_status()

123