| #
4f66e09b |
| 09-May-2017 |
Stefano Babic <sbabic@denx.de> |
Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
| #
ef3f3b81 |
| 23-Feb-2017 |
Uri Mashiach <uri.mashiach@compulab.co.il> |
arm: usb: dra7xx: xHCI registers based on USB port index
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the
arm: usb: dra7xx: xHCI registers based on USB port index
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
show more ...
|
| #
042fdb7c |
| 29-Nov-2016 |
Nishanth Menon <nm@ti.com> |
usb: xhci: Remove assumption of DWC instance based on DRA7 SoC type
Both AM57xx and DRA7xx share the same set of base addresses for DWC
controllers. The usage however differ with DWC2 instance used
usb: xhci: Remove assumption of DWC instance based on DRA7 SoC type
Both AM57xx and DRA7xx share the same set of base addresses for DWC
controllers. The usage however differ with DWC2 instance used typically
in AM57xx evms while DWC1 instances used in DRA7x platforms.
Use TARGET_SOC config to differentiate so that CONFIG_AM57XX can be dropped.
Eventually, this needs to be dt-fied.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
show more ...
|
| #
98d2d5e8 |
| 08-Dec-2014 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-ti
|
| #
d11ac4b5 |
| 06-Nov-2014 |
Felipe Balbi <balbi@ti.com> |
arm: omap: add support for am57xx devices
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
| #
748bde60 |
| 21-Oct-2013 |
Tom Rini <trini@ti.com> |
Merge branch 'master' of git://git.denx.de/u-boot-usb
|
| #
3d799c7f |
| 11-Oct-2013 |
Dan Murphy <dmurphy@ti.com> |
usb: am437x: Add support for am437x xhci USB host
Add the support for the am437x xhci usb host.
The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Sig
usb: am437x: Add support for am437x xhci USB host
Add the support for the am437x xhci usb host.
The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
show more ...
|
| #
834e91af |
| 11-Oct-2013 |
Dan Murphy <dmurphy@ti.com> |
usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHC
usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
show more ...
|
| #
ba55453c |
| 11-Oct-2013 |
Dan Murphy <dmurphy@ti.com> |
usb: omap: Move the usb phy code to the usb/phy directory
Moving the usb/phy code from xhci-omap to the usb/phy directory
and moving the associated phy code over to the new file.
Newer TI processor
usb: omap: Move the usb phy code to the usb/phy directory
Moving the usb/phy code from xhci-omap to the usb/phy directory
and moving the associated phy code over to the new file.
Newer TI processors adding xHCI support will have different PHY configurations
so therefore abstracting this code away will prevent messing around with the
xhci-omap file itself.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
show more ...
|
| #
41b667b8 |
| 11-Oct-2013 |
Dan Murphy <dmurphy@ti.com> |
usb: omap: Move the xhci-omap header file to common location
Moving the xhci-omap header to a more global location so that
other code can reference this code.
Signed-off-by: Dan Murphy <dmurphy@ti.
usb: omap: Move the xhci-omap header file to common location
Moving the xhci-omap header to a more global location so that
other code can reference this code.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
show more ...
|