spl: Move spl_board_load_image() into a generic header

At present this is only used on ARM and sandbox, but it is just as
applicable to other architectures. Move the function prototype into the
gene

spl: Move spl_board_load_image() into a generic header

At present this is only used on ARM and sandbox, but it is just as
applicable to other architectures. Move the function prototype into the
generic SPL header.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

armv7: ls1021a: Move DDR config options to Kconfig

Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Gl

armv7: ls1021a: Move DDR config options to Kconfig

Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

armv8: fsl-layerscape: Move DDR config options to Kconfig

Move DDR3, DDR4 and realted options to Kconfig and clean up existing
uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Gl

armv8: fsl-layerscape: Move DDR config options to Kconfig

Move DDR3, DDR4 and realted options to Kconfig and clean up existing
uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

arm: Move SYS_FSL_SRDS_* and SYS_HAS_SERDES to Kconfig

Move these options to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.or

arm: Move SYS_FSL_SRDS_* and SYS_HAS_SERDES to Kconfig

Move these options to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

arm: Move FSL_HAS_DP_DDR and NUM_DDR_CONTROLLERS to Kconfig

Move this option to Kconfig and clean up existing uses.
NUM_DDR_CONTROLLERS is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.s

arm: Move FSL_HAS_DP_DDR and NUM_DDR_CONTROLLERS to Kconfig

Move this option to Kconfig and clean up existing uses.
NUM_DDR_CONTROLLERS is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

arm: Move SYS_FSL_IFC_BANK_COUNT to Kconfig

Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by:

arm: Move SYS_FSL_IFC_BANK_COUNT to Kconfig

Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

arm: Move MAX_CPUS to Kconfig

Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Review

arm: Move MAX_CPUS to Kconfig

Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

armv8/fsl-lsch2: Implement workaround for PIN MUX erratum A010539

Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC

armv8/fsl-lsch2: Implement workaround for PIN MUX erratum A010539

Pin mux logic has 2 options in priority order, one is through RCW_SRC
and then through RCW_Fields. In case of QSPI booting, RCW_SRC logic
takes the priority for SPI pads and do not allow RCW_BASE and SPI_EXT
to control the SPI muxing. But actually those are DSPI controller's
pads instead of QSPI controller's, so this workaround allows RCW
fields SPI_BASE and SPI_EXT to control relevant pads muxing.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8: fsl-layerscape: Fix "cpu status" command

The core position is not continuous for some SoCs. For example,
valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some
registers (including b

armv8: fsl-layerscape: Fix "cpu status" command

The core position is not continuous for some SoCs. For example,
valid cores may present at position 0, 1, 4, 5, 8, 9, etc. Some
registers (including boot release register) only count existing
cores. Current implementation of cpu_mask() complies with the
continuous numbering. However, command "cpu status" queries the
spin table with actual core position. Add functions to calculate
core position from core number, to correctly calculate offsets.

Tested on LS2080ARDB and LS1043ARDB.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: fsl-lsch2: enable snoopable sata read and write

By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCN

armv8: fsl-lsch2: enable snoopable sata read and write

By default the SATA IP on the ls1043a/ls1046a SoCs does not
generating coherent/snoopable transactions. This patch enable
it in the SCFG_SNPCNFGCR register along with sata axicc register.
In addition, the dma-coherent property must be set on the SATA
controller nodes.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
[York Sun: Reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8: fsl-lsch2: adjust sata parameter

The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp

armv8: fsl-lsch2: adjust sata parameter

The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

imx-common: enlarge mux width to 4

For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.

Signed-off-by: Peng Fan <peng.f

imx-common: enlarge mux width to 4

For i.MX6, the mux width is 4, not 3. So enlarge the width.
IOMUX_CONFIG_LPSR is changed from 0x8 to 0x20 to not use bit 3 of mux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: iomux: fix snvs usage for i.MX6ULL

SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.

Use IOMUX_CONFIG_LPSR flag for these p

imx: iomux: fix snvs usage for i.MX6ULL

SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module,
not in IOMUXC, so correct the related registers' offset.

Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate
them from iomuxc pins.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>

show more ...

imx: imx6ull: adjust the ldo 1.2v bandgap voltage

Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting t

imx: imx6ull: adjust the ldo 1.2v bandgap voltage

Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: Update memory map address

Update memory map address for mx6ull.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

imx: mx6ull: update clock settings and CCM register map

Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc:

imx: mx6ull: update clock settings and CCM register map

Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx-common: introduce is_mx6ull

Introduce is_mx6ull macro.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

imx: mx6ull: add mx6ull major cpu type

Add i.MX6ULL major cpu type.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: S

imx: mx6ull: add mx6ull major cpu type

Add i.MX6ULL major cpu type.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ull: add iomux header file

Add iomux header file for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by

imx: mx6ull: add iomux header file

Add iomux header file for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge git://git.denx.de/u-boot-rockchip

arm: omap5: secure API for EMIF memory reservations

Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of t

arm: omap5: secure API for EMIF memory reservations

Create a few public APIs which rely on secure world ROM/HAL
APIs for their implementation. These are intended to be used
to reserve a portion of the EMIF memory and configure hardware
firewalls around that region to prevent public code from
manipulating or interfering with that memory.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

rockchip: add boot-mode support for rk3288, rk3036

rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we s

rockchip: add boot-mode support for rk3288, rk3036

rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.

We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.

Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

rockchip: rkpwm: fix the register sequence

Reference to kernel source code, rockchip pwm has three
type, we are using v2 for rk3288 and rk3399, so let's
update the register to sync with pwm_data_v2

rockchip: rkpwm: fix the register sequence

Reference to kernel source code, rockchip pwm has three
type, we are using v2 for rk3288 and rk3399, so let's
update the register to sync with pwm_data_v2 in kernel.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

rockchip: rk3399: update PPLL and pmu_pclk frequency

Update PPLL to 676MHz and PMU_PCLK to 48MHz, because:
1. 48MHz can make sure the pwm can get exact 50% duty ratio, but 99MHz
can not,
2. We think

rockchip: rk3399: update PPLL and pmu_pclk frequency

Update PPLL to 676MHz and PMU_PCLK to 48MHz, because:
1. 48MHz can make sure the pwm can get exact 50% duty ratio, but 99MHz
can not,
2. We think 48MHz is fast enough for pmu pclk and it is lower power cost
than 99MHz,
3. PPLL 676 MHz and PMU_PCLK 48MHz are the clock rate we are using
internally for kernel,it suppose not to change the bus clock like pmu_pclk
in kernel, so we want to change it in uboot.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-usb

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
include/configs/dra7xx_evm.h