| /rk3399_rockchip-uboot/board/keymile/scripts/ |
| H A D | README | 14 This file defines variables for working with rootfs via nfs for powerpc and
19 This file defines architecture specific variables for working with rootfs via
25 This file defines variables for working with rootfs inside the ram for powerpc
30 This file defines architecture specific variables for working with rootfs inside
|
| /rk3399_rockchip-uboot/board/qualcomm/dragonboard410c/ |
| H A D | readme.txt | 33 What is working:
43 What is not working / known bugs:
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/usb/ |
| H A D | tegra-usb.txt | 16 - dr_mode : dual role mode. Indicates the working mode for
|
| /rk3399_rockchip-uboot/tools/kermit/ |
| H A D | README | 9 that need to be done frequently when working with U-Boot.
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/clock/ |
| H A D | rockchip,rk3399-dmc.txt | 12 dmc_clk: for ddr working frequency
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | README.update | 68 Assuming that an U-Boot image u-boot.bin is present in the current working
87 file is a good, working image. Also make sure that the address in Flash
|
| H A D | README.mpc85xx | 53 2) TLB entry for working in AS1
104 2) TLB entry for working in AS1
|
| H A D | README.hwconfig | 20 2. Since we don't implement a hwconfig command, i.e. we're working
|
| H A D | README.fdt-overlays | 87 3. Set it as the working fdt tree.
|
| H A D | README.console | 32 and get them working on the next startup, too.
|
| H A D | README.NetConsole | 33 specify the target IP address (or host name, assuming DNS is working). The
|
| H A D | README.nokia_rx51 | 90 ONENAND support is disabled because not working yet and cause linux kernel to
|
| H A D | README.ramboot-ppc85xx | 27 Suppose the board already has a working bootloader on it. And you would
|
| /rk3399_rockchip-uboot/board/pb1x00/ |
| H A D | README | 10 I have not tested, but several u-boot users report working
|
| /rk3399_rockchip-uboot/board/dbau1x00/ |
| H A D | README | 10 I have not tested, but several u-boot users report working
|
| /rk3399_rockchip-uboot/arch/arm/cpu/armv7/ |
| H A D | cache_v7_asm.S | 52 mov r9, r7 @ create working copy of max index
125 mov r9, r7 @ create working copy of max index
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/leds/ |
| H A D | leds-bcm6328.txt | 11 controlled, so the only chance to keep them working is by using this driver.
|
| /rk3399_rockchip-uboot/examples/standalone/ |
| H A D | README_rkspi.md | 59 - rsd: read sample clock shift with spiclk which is controller working rate
|
| /rk3399_rockchip-uboot/board/freescale/mpc8569mds/ |
| H A D | README | 77 very important to get the board booting up and working properly.
|
| /rk3399_rockchip-uboot/board/work-microwave/work_92105/ |
| H A D | README | 71 The following assumes a working U-Boot on the target, with the ability
|
| /rk3399_rockchip-uboot/arch/arm/dts/ |
| H A D | sun8i-a23-evb.dts | 128 * line and get a working UART.
|
| /rk3399_rockchip-uboot/drivers/ddr/altera/ |
| H A D | sequencer.c | 1557 static int sdr_find_phase_delay(int working, int delay, const u32 grp, in sdr_find_phase_delay() argument
1572 if (!working) in sdr_find_phase_delay()
1594 static int sdr_find_phase(int working, const u32 grp, u32 *work, in sdr_find_phase() argument
1597 const u32 end = misccfg->read_valid_fifo_size + (working ? 0 : 1); in sdr_find_phase()
1601 if (working) in sdr_find_phase()
1604 ret = sdr_find_phase_delay(working, 0, grp, work, in sdr_find_phase()
1612 if (!working) in sdr_find_phase()
|
| /rk3399_rockchip-uboot/drivers/video/ |
| H A D | Kconfig | 357 working LCD configuration. The exact role of SPI may differ for
367 working LCD configuration. The exact role of SPI may differ for
377 working LCD configuration. The exact role of SPI may differ for
387 working LCD configuration. The exact role of SPI may differ for
515 This enables framebuffer driver for i.MX processors working
|
| /rk3399_rockchip-uboot/board/hisilicon/hikey/ |
| H A D | README | 104 Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
107 See working boot trace below (by default trace is now output to UART3 not UART0 on latest
|
| /rk3399_rockchip-uboot/doc/uImage.FIT/ |
| H A D | howto.txt | 78 in the current working directory; if desired, an alternative path can be
189 the current working directory -- image source file kernel_fdt.its can be
|