Home
last modified time | relevance | path

Searched refs:initial (Results 1 – 25 of 47) sorted by relevance

12

/rk3399_rockchip-uboot/doc/
H A DREADME.arm645 The initial arm64 U-Boot port was developed before hardware was available,
15 classical firmware (like initial hardware setup, CPU errata workarounds
22 is used to encode the initial addend of rela to u-boot.bin. After running,
H A DREADME.update39 These knobs control the timeouts during initial connection to the TFTP
43 the server to respond to initial connection, and CONFIG_UPDATE_TFTP_CNT_MAX
H A DREADME.semihosting19 The initial vexpress64 u-boot board created here runs on the VE virtual
H A DREADME.LED28 CONFIG_STATUS_LED_STATE is the initial state of the LED. It should be set to one
H A DREADME.davinci92 by a programmer. During initial bootup, the ROM Bootloader reads the UBL
H A DREADME.ramboot-ppc85xx8 - In case of NAND boot FCM supports loading initial 4K code from NAND flash
H A DREADME.m68k96 initial vector table and basic processor initialization will not
/rk3399_rockchip-uboot/arch/arm/dts/
H A Dstm32mp157a-dk1.dts113 regulator-initial-mode = <0>;
122 regulator-initial-mode = <0>;
132 regulator-initial-mode = <0>;
142 regulator-initial-mode = <0>;
H A Drk3229-gva.dts134 regulator-initial-mode = <0x1>;
150 regulator-initial-mode = <0x1>;
164 regulator-initial-mode = <0x1>;
178 regulator-initial-mode = <0x1>;
H A Drk3326-evb.dts161 regulator-initial-mode = <0x1>;
175 regulator-initial-mode = <0x1>;
186 regulator-initial-mode = <0x1>;
198 regulator-initial-mode = <0x1>;
H A Dpx30-evb.dts176 regulator-initial-mode = <0x1>;
190 regulator-initial-mode = <0x1>;
201 regulator-initial-mode = <0x1>;
213 regulator-initial-mode = <0x1>;
H A Ddra72-evm-common.dtsi228 lines-initial-states = <0x1408>;
262 * initial state is used here to keep the mdio interface
267 lines-initial-states = <0x0f2b>;
H A Drk3399-puma.dtsi237 regulator-initial-state = <3>;
439 regulator-initial-state = <3>;
/rk3399_rockchip-uboot/drivers/led/
H A DKconfig117 int "initial state"
152 int "initial state"
187 int "initial state"
222 int "initial state"
257 int "initial state"
292 int "initial state"
/rk3399_rockchip-uboot/drivers/usb/gadget/
H A Ddesignware_udc.c91 static void udc_state_transition(usb_device_state_t initial, in udc_state_transition() argument
94 if (initial < final) { in udc_state_transition()
95 switch (initial) { in udc_state_transition()
117 } else if (initial > final) { in udc_state_transition()
118 switch (initial) { in udc_state_transition()
/rk3399_rockchip-uboot/doc/device-tree-bindings/gpio/
H A Dgpio-pcf857x.txt39 - lines-initial-states: Bitmask that specifies the initial state of each
/rk3399_rockchip-uboot/doc/device-tree-bindings/leds/
H A Dleds-gpio.txt17 - default-state: (optional) The initial state of the LED. Valid
/rk3399_rockchip-uboot/api/
H A DREADME10 once this initial version proves functional
/rk3399_rockchip-uboot/arch/mips/
H A DKconfig331 Select this if the initial stack frame could be setup in SRAM.
332 Normally the initial stack frame is set up in DRAM which is often
333 only available after lowlevel_init. With this option the initial
/rk3399_rockchip-uboot/board/freescale/m5253evbe/
H A DREADME16 2.1. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
/rk3399_rockchip-uboot/arch/xtensa/cpu/
H A Du-boot.lds26 * initial stack. Not all Xtensa processor configurations support that, so
/rk3399_rockchip-uboot/board/Synology/ds109/
H A Dopenocd.cfg28 # possible that initial tap examination failed. So let's
/rk3399_rockchip-uboot/
H A DKconfig92 initial serial device and any others that are needed.
102 initial serial device and any others that are needed.
112 initial serial device and any others that are needed.
122 initial serial device and any others that are needed.
/rk3399_rockchip-uboot/board/cadence/xtfpga/
H A DREADME89 After initial startup, the MAC address is stored in the U-Boot
/rk3399_rockchip-uboot/board/buffalo/lsxl/
H A DREADME8 bootloader and its environment. The linux kernel and the initial ramdisk

12