| /rk3399_rockchip-uboot/drivers/ddr/marvell/a38x/ |
| H A D | ddr3_training_ip_engine.h | 20 #define GET_TAP_RESULT(reg, edge) \ argument
21 (((edge) == EDGE_1) ? ((reg) & PUP_RESULT_EDGE_1_MASK) : \
36 enum hws_edge_compare edge,
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/video/ |
| H A D | display-timing.txt | 30 - active high = drive pixel data on rising edge/
31 sample data on falling edge
32 - active low = drive pixel data on falling edge/
33 sample data on rising edge
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/gpio/ |
| H A D | nvidia,tegra20-gpio.txt | 17 1 = low-to-high edge triggered.
18 2 = high-to-low edge triggered.
|
| H A D | nvidia,tegra186-gpio.txt | 120 - 1: Low-to-high edge triggered.
121 - 2: High-to-low edge triggered.
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | I2C_Edge_Conditions | 7 The edge condition is as follows:
33 This reset edge condition could possibly be present in every I2C
|
| /rk3399_rockchip-uboot/arch/arm/dts/ |
| H A D | am335x-pxm50.dts | 33 sync-edge = <0>;
|
| H A D | fsl-ls2080a.dtsi | 43 interrupts = <0 32 0x1>; /* edge triggered */
51 interrupts = <0 32 0x1>; /* edge triggered */
|
| H A D | stm32mp157a-dk1.dts | 252 st,neg-edge;
|
| /rk3399_rockchip-uboot/board/theobroma-systems/puma_rk3399/ |
| H A D | README | 20 * Camera: 2x CSI (one on the edge connector, one on the Q7 specified CSI ZIF)
|
| /rk3399_rockchip-uboot/board/Seagate/nas220/ |
| H A D | kwbimage.cfg | 38 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Marvell/guruplug/ |
| H A D | kwbimage.cfg | 35 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Seagate/dockstar/ |
| H A D | kwbimage.cfg | 38 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Synology/ds109/ |
| H A D | kwbimage.cfg | 39 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Marvell/dreamplug/ |
| H A D | kwbimage.cfg | 36 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Seagate/goflexhome/ |
| H A D | kwbimage.cfg | 41 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Marvell/sheevaplug/ |
| H A D | kwbimage.cfg | 35 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/LaCie/netspace_v2/ |
| H A D | kwbimage.cfg | 36 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| H A D | kwbimage-is2.cfg | 36 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| H A D | kwbimage-ns2l.cfg | 36 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/cloudengines/pogo_e02/ |
| H A D | kwbimage.cfg | 39 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/raidsonic/ib62x0/ |
| H A D | kwbimage.cfg | 36 # bit6: 0x0, use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/keymile/km_arm/ |
| H A D | kwbimage.cfg | 56 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/LaCie/net2big_v2/ |
| H A D | kwbimage.cfg | 36 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/Marvell/openrd/ |
| H A D | kwbimage.cfg | 35 # bit 6: 0=use recommended falling edge of clk for addr/cmd
|
| /rk3399_rockchip-uboot/board/iomega/iconnect/ |
| H A D | kwbimage.cfg | 35 # bit6: 0x0, use recommended falling edge of clk for addr/cmd
|