Searched refs:dir_reg (Results 1 – 5 of 5) sorted by relevance
| /OK3568_Linux_fs/kernel/drivers/misc/rk628/ |
| H A D | rk628_pinctrl.c | 151 int i, dir_reg, offset, val; in rk628_misc_gpio_set_direction() local
157 dir_reg = rk628_pin_iomux_groups[i].gpio_base + GPIO_SWPORT_DDR_H; in rk628_misc_gpio_set_direction()
160 dir_reg = rk628_pin_iomux_groups[i].gpio_base + GPIO_SWPORT_DDR_L; in rk628_misc_gpio_set_direction()
166 if ((i == ARRAY_SIZE(rk628_pin_iomux_groups)) || (!dir_reg)) { in rk628_misc_gpio_set_direction()
176 rk628_i2c_write(rk628, dir_reg, val); in rk628_misc_gpio_set_direction()
|
| /OK3568_Linux_fs/kernel/drivers/pinctrl/ |
| H A D | pinctrl-rk628.c | 475 int dir_reg, val, ret; in rk628_gpio_get_direction() local
478 dir_reg = bank->reg_base + GPIO_SWPORT_DDR_H; in rk628_gpio_get_direction()
481 dir_reg = bank->reg_base + GPIO_SWPORT_DDR_L; in rk628_gpio_get_direction()
485 ret = regmap_read(pci->regmap, dir_reg, &val); in rk628_gpio_get_direction()
677 int pin_offset, dir_reg, val, ret; in rk628_pmx_gpio_set_direction() local
684 dir_reg = bank->reg_base + GPIO_SWPORT_DDR_H; in rk628_pmx_gpio_set_direction()
687 dir_reg = bank->reg_base + GPIO_SWPORT_DDR_L; in rk628_pmx_gpio_set_direction()
695 ret = regmap_write(pci->regmap, dir_reg, val); in rk628_pmx_gpio_set_direction()
|
| /OK3568_Linux_fs/kernel/drivers/mfd/ |
| H A D | asic3.c | 552 u16 dir_reg[ASIC3_NUM_GPIO_BANKS]; in asic3_gpio_probe() local
557 memset(dir_reg, 0, ASIC3_NUM_GPIO_BANKS * sizeof(u16)); in asic3_gpio_probe()
579 dir_reg[bank_num] |= (dir << bit_num); in asic3_gpio_probe()
586 dir_reg[i]); in asic3_gpio_probe()
|
| /OK3568_Linux_fs/kernel/drivers/gpio/ |
| H A D | gpio-stmpe.c | 259 u8 dir_reg = stmpe->regs[STMPE_IDX_GPDR_LSB + bank]; in stmpe_dbg_show_one() local
264 ret = stmpe_reg_read(stmpe, dir_reg); in stmpe_dbg_show_one()
|
| /OK3568_Linux_fs/kernel/drivers/media/tuners/ |
| H A D | r820t.c | 1809 u8 dir_reg, other_reg; in r820t_iq() local
1818 dir_reg = 0x08; in r820t_iq()
1821 dir_reg = 0x09; in r820t_iq()
1829 rc = r820t_compre_step(priv, compare_iq, dir_reg); in r820t_iq()
1835 compare_iq[0].phase_y, dir_reg); in r820t_iq()
|