Home
last modified time | relevance | path

Searched refs:DEBUG_INIT_S (Results 1 – 9 of 9) sorted by relevance

/OK3568_Linux_fs/u-boot/drivers/ddr/marvell/axp/
H A Dddr3_init.h21 #define DEBUG_INIT_S(s) puts(s) macro
25 #define DEBUG_INIT_S(s) macro
35 { DEBUG_INIT_S("Write Reg: 0x"); DEBUG_INIT_D((reg), 8); \
36 DEBUG_INIT_S("= "); DEBUG_INIT_D((val), 8); DEBUG_INIT_S("\n"); }
38 { DEBUG_INIT_S("Read Reg: 0x"); DEBUG_INIT_D((reg), 8); \
39 DEBUG_INIT_S("= "); DEBUG_INIT_D((val), 8); DEBUG_INIT_S("\n"); }
51 { DEBUG_INIT_S(s); DEBUG_INIT_D(d, l); DEBUG_INIT_S("\n"); }
H A Dddr3_init.c284 DEBUG_INIT_S("DDR3 Training Error: Bad sample at reset"); in ddr3_init()
286 DEBUG_INIT_S("DDR3 Training Error: Bad DIMM setup"); in ddr3_init()
288 DEBUG_INIT_S("DDR3 Training Error: Max CS limit"); in ddr3_init()
290 DEBUG_INIT_S("DDR3 Training Error: Max enable CS limit"); in ddr3_init()
292 DEBUG_INIT_S("DDR3 Training Error: Bad R-DIMM setup"); in ddr3_init()
294 DEBUG_INIT_S("DDR3 Training Error: TWSI failure"); in ddr3_init()
296 DEBUG_INIT_S("DDR3 Training Error: DIMM type no match"); in ddr3_init()
298 DEBUG_INIT_S("DDR3 Training Error: TWSI bad type"); in ddr3_init()
300 DEBUG_INIT_S("DDR3 Training Error: bus width no match"); in ddr3_init()
372 DEBUG_INIT_S("4\n"); in ddr3_init_main()
[all …]
H A Dddr3_spd.c514 DEBUG_INIT_S("DDR3 Dimm Compare - DIMM type does not match - FAIL\n"); in ddr3_spd_sum_init()
519 DEBUG_INIT_S("DDR3 Dimm Compare - ECC does not match. ECC is disabled\n"); in ddr3_spd_sum_init()
522 DEBUG_INIT_S("DDR3 Dimm Compare - DRAM bus width does not match - FAIL\n"); in ddr3_spd_sum_init()
616 DEBUG_INIT_S("DDR3 Training Sequence - No DIMMs detected\n");
618 DEBUG_INIT_S("DDR3 Training Sequence - FAILED (Wrong DIMMs Setup)\n");
727 DEBUG_INIT_S("DDR3 Training Sequence - FAIL - Illegal R-DIMM setup\n");
1195 DEBUG_INIT_S("DDR3 Training Sequence - Registered DIMM detected\n");
/OK3568_Linux_fs/u-boot/drivers/ddr/marvell/a38x/
H A Dddr3_init.h36 #define DEBUG_INIT_S(s) puts(s) macro
40 #define DEBUG_INIT_S(s) macro
50 { DEBUG_INIT_S("Write Reg: 0x"); DEBUG_INIT_D((reg), 8); \
51 DEBUG_INIT_S("= "); DEBUG_INIT_D((val), 8); DEBUG_INIT_S("\n"); }
53 { DEBUG_INIT_S("Read Reg: 0x"); DEBUG_INIT_D((reg), 8); \
54 DEBUG_INIT_S("= "); DEBUG_INIT_D((val), 8); DEBUG_INIT_S("\n"); }
68 { DEBUG_INIT_S(s); DEBUG_INIT_D(d, l); DEBUG_INIT_S("\n"); }
H A Dddr3_init.c505 DEBUG_INIT_S("\n*** Error: ddr3_get_static_ddr_mode: No match for requested DDR mode. ***\n\n"); in ddr3_get_static_ddr_mode()
/OK3568_Linux_fs/u-boot/arch/arm/mach-mvebu/serdes/a38x/
H A Dctrl_pex.c117 DEBUG_INIT_S("PCIe, Idx "); in hws_pex_config()
119 DEBUG_INIT_S(": detected no link\n"); in hws_pex_config()
146 DEBUG_INIT_S(":** Link is Gen1, check the EP capability\n"); in hws_pex_config()
166 DEBUG_INIT_S("PCIe, Idx "); in hws_pex_config()
168 DEBUG_INIT_S(": remains Gen1\n"); in hws_pex_config()
192 DEBUG_INIT_S("PCIe, Idx "); in hws_pex_config()
194 DEBUG_INIT_S in hws_pex_config()
H A Dhigh_speed_env_spec.c1366 DEBUG_INIT_S("board SerDes lanes topology details:\n"); in print_topology_details()
1368 DEBUG_INIT_S(" | Lane # | Speed | Type |\n"); in print_topology_details()
1369 DEBUG_INIT_S(" --------------------------------\n"); in print_topology_details()
1373 DEBUG_INIT_S(" | "); in print_topology_details()
1375 DEBUG_INIT_S(" | "); in print_topology_details()
1377 DEBUG_INIT_S(" | "); in print_topology_details()
1378 DEBUG_INIT_S((char *) in print_topology_details()
1381 DEBUG_INIT_S("\t|\n"); in print_topology_details()
1383 DEBUG_INIT_S(" --------------------------------\n"); in print_topology_details()
1418 DEBUG_INIT_S("High speed PHY - Version: "); in serdes_phy_config()
[all …]
H A Dseq_exec.c120 DEBUG_INIT_S("poll_op_execute: TIMEOUT\n"); in poll_op_execute()
/OK3568_Linux_fs/u-boot/arch/arm/mach-mvebu/serdes/axp/
H A Dhigh_speed_env_lib.c287 DEBUG_INIT_S("High speed PHY - Version: "); in serdes_phy_config()
288 DEBUG_INIT_S(SERDES_VERSION); in serdes_phy_config()
289 DEBUG_INIT_S(" - 2nd boot - Skip\n"); in serdes_phy_config()
292 DEBUG_INIT_S("High speed PHY - Version: "); in serdes_phy_config()
293 DEBUG_INIT_S(SERDES_VERSION); in serdes_phy_config()
294 DEBUG_INIT_S(" (COM-PHY-V20)\n"); in serdes_phy_config()
359 DEBUG_INIT_S("Hight speed PHY Error #1\n"); in serdes_phy_config()
1264 DEBUG_INIT_S("PEX"); in serdes_phy_config()
1415 DEBUG_INIT_S(ENDED_OK); in serdes_phy_config()