| /OK3568_Linux_fs/kernel/Documentation/arm/ |
| H A D | setup.rst | 2 Kernel initialisation parameters on ARM Linux
5 The following document describes the kernel initialisation parameter
9 This structure is used to pass initialisation parameters from the
11 through the kernel initialisation process. As a general rule, it
|
| /OK3568_Linux_fs/kernel/drivers/gpu/arm/midgard/ |
| H A D | mali_kbase_config.h | 309 * kbase_platform_early_init - Early initialisation of the platform code
312 * early initialisation required by the platform code. Such as reading
315 * Return: 0 for success, any other fail causes module initialisation to fail
325 * is not enabled and the platform initialisation code in the kernel doesn't
328 * Return: 0 for success, any other fail causes module initialisation to fail
|
| /OK3568_Linux_fs/kernel/include/linux/regulator/ |
| H A D | userspace-consumer.h | 9 * initialisation data.
15 * enabled during initialisation
|
| H A D | machine.h | 136 * initialisation.
220 * struct regulator_init_data - regulator platform initialisation data.
222 * Initialisation constraints, our supply and consumers supplies.
|
| /OK3568_Linux_fs/kernel/Documentation/devicetree/bindings/mfd/ |
| H A D | cirrus,lochnagar.yaml | 143 Initialisation data for the VDDCORE regulator, which supplies the
160 Initialisation data for the MICVDD regulator, which supplies the
177 Initialisation data for the MIC1VDD supplies.
202 Initialisation data for the MIC2VDD supplies.
|
| /OK3568_Linux_fs/kernel/include/xen/interface/io/ |
| H A D | xenbus.h | 14 status of initialisation across the bus. States here imply nothing about
22 initialisation, but waiting
|
| /OK3568_Linux_fs/kernel/sound/aoa/ |
| H A D | aoa-gpio.h | 24 /* for initialisation/de-initialisation of the GPIO layer */
|
| /OK3568_Linux_fs/kernel/Documentation/power/regulator/ |
| H A D | machine.rst | 6 initialisation code to configure the regulator subsystem.
16 initialisation code by creating a struct regulator_consumer_supply for
|
| H A D | overview.rst | 46 bootloader, firmware or kernel board initialisation code.
105 level board initialisation code. It is used to constrain a
|
| /OK3568_Linux_fs/kernel/arch/arm/mach-s3c/ |
| H A D | cpu.h | 92 /* per-cpu initialisation function table. */
107 /* core initialisation functions */
|
| H A D | init.c | 7 // S3C series CPU initialisation
101 * early initialisation of the console.
|
| /OK3568_Linux_fs/kernel/arch/mips/dec/ |
| H A D | setup.c | 159 * Machine-specific initialisation for KN01, aka DS2100 (aka Pmin)
237 * Machine-specific initialisation for KN230, aka DS5100, aka MIPSmate.
312 * Machine-specific initialisation for KN02, aka DS5000/200, aka 3max.
407 * Machine-specific initialisation for KN02-BA, aka DS5000/1xx
508 * Machine-specific initialisation for KN02-CA, aka DS5000/xx,
605 * Machine-specific initialisation for KN03, aka DS5000/240,
|
| /OK3568_Linux_fs/kernel/drivers/mfd/ |
| H A D | wm8400-core.c | 45 * wm8400_init - Generic initialisation
93 dev_warn(wm8400->dev, "No platform initialisation supplied\n"); in wm8400_init()
|
| /OK3568_Linux_fs/kernel/drivers/clk/keystone/ |
| H A D | pll.c | 153 * _of_pll_clk_init - PLL initialisation via DT
223 * of_keystone_pll_clk_init - PLL initialisation DT wrapper
234 * of_keystone_main_pll_clk_init - Main PLL initialisation DT wrapper
|
| /OK3568_Linux_fs/kernel/Documentation/driver-api/usb/ |
| H A D | callbacks.rst | 83 genuine error occurred during initialisation which prevented a driver
90 initialisation that doesn't take too long is a good idea here.
|
| /OK3568_Linux_fs/u-boot/arch/arm/mach-sunxi/ |
| H A D | dram_sun9i.c | 2 * sun9i dram controller initialisation
470 * DRAM3 initialisation requires holding CKE LOW for in mctl_channel_init()
471 * at least 500us prior to starting the initialisation in mctl_channel_init()
473 * before the initialisation sequence may be started). in mctl_channel_init()
496 * after driving CKE HIGH in the initialisation sequence. in mctl_channel_init()
587 * initialisation when the PHY initialisation completes). in mctl_channel_init()
624 /* PHY initialisation */ in mctl_channel_init()
|
| /OK3568_Linux_fs/kernel/Documentation/networking/device_drivers/wan/ |
| H A D | z8530book.rst | 85 channels and do any necessary board level initialisation to configure
134 a channel be aware that the documentation recommends initialisation
138 initialisation values in an array of u8 type. The first value is the
|
| /OK3568_Linux_fs/u-boot/doc/ |
| H A D | README.generic-board | 13 initialisation slightly differently. To address this, a new 'generic board
49 initialisation is painful since it must be independently added in 10
|
| /OK3568_Linux_fs/kernel/drivers/pcmcia/ |
| H A D | soc_common.h | 119 * Enable card status IRQs on (re-)initialisation. This can
120 * be called at initialisation, power management event, or
|
| /OK3568_Linux_fs/kernel/arch/x86/include/asm/ |
| H A D | setup_arch.h | 1 /* Hook to call BIOS initialisation function */
|
| /OK3568_Linux_fs/kernel/Documentation/filesystems/caching/ |
| H A D | operations.rst | 13 (*) Operation record initialisation.
37 Operation Record Initialisation
|
| /OK3568_Linux_fs/kernel/arch/s390/mm/ |
| H A D | kasan_init.c | 41 kasan_early_panic("out of memory during initialisation\n"); in kasan_early_alloc_segment()
51 kasan_early_panic("out of memory during initialisation\n"); in kasan_early_alloc_pages()
344 kasan_early_panic("out of memory during initialisation\n"); in kasan_early_init()
|
| /OK3568_Linux_fs/u-boot/board/intel/edison/ |
| H A D | start.S | 12 /* No 32-bit board specific initialisation */
|
| /OK3568_Linux_fs/u-boot/board/coreboot/coreboot/ |
| H A D | coreboot_start.S | 12 /* No 32-bit board specific initialisation */
|
| /OK3568_Linux_fs/u-boot/board/efi/ |
| H A D | Kconfig | 11 this case EFI does the early initialisation, and U-Boot
|