powerpc/mpc85xx:Increase binary size for P, B & T series boards.

u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
li

powerpc/mpc85xx:Increase binary size for P, B & T series boards.

u-boot binary size for Freescale mpc85xx platforms is 512KB.
This has been reached to upper limit for some of the platforms causig
linker error.

So, Increase the u-boot binary size to 768KB.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by:

board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

show more ...

kgdb: configs: remove obsolete CONFIG_KGDB_SER_INDEX

The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
car

kgdb: configs: remove obsolete CONFIG_KGDB_SER_INDEX

The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years
ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should
care about this parameter or it should be gone completely.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard

Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compul

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard

Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds

show more ...

powerpc/p1010rdb:modify the mtest start_address

In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.

Signed-off-by

powerpc/p1010rdb:modify the mtest start_address

In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed

Driver/DDR: Moving Freescale DDR driver to a common driver

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>

show more ...

p1010rdb: enable mtdparts for NAND

The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.

Signe

p1010rdb: enable mtdparts for NAND

The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.

Signed-off-by: Zhao Qiang <B45475@freescale.com>

show more ...

config: remove platform CONFIG_SYS_HZ definition part 1/2

Remove platform CONFIG_SYS_HZ definition for configs A-Z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this t

config: Add a default CONFIG_SYS_PROMPT

The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

show more ...

powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-pa

- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.

For more details, see b

powerpc/p1010rdb: add p1010rdb-pb support with updating p1010rdb-pa

- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.

For more details, see board/freescale/p1010rdb/README.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>

show more ...

board/p1010rdb: add pin mux and sdhc support in any boot

Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use c

board/p1010rdb: add pin mux and sdhc support in any boot

Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use case in runtime without reboot system
run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
b) For long-term use case
set 'esdhc' in hwconfig and save it.
To enable IFC in case of SD boot
a) For temporary use case in runtime without reboot system
run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
b) For long-term use case
set 'ifc' in hwconfig and save it.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>

show more ...

powerpc: add CONFIG_SECURE_BOOT condition into fsl_secure_boot.h

This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.

Signed-off-by: Po

powerpc: add CONFIG_SECURE_BOOT condition into fsl_secure_boot.h

This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.

Signed-off-by: Po Liu <Po.Liu@freescale.com>

show more ...

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <s

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'u-boot/master' into u-boot-arm/master

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

i2c, fsl_i2c: switch to new multibus/multiadapter support

- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schoche

i2c, fsl_i2c: switch to new multibus/multiadapter support

- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

show more ...

i2c, soft-i2c: switch to new multibus/multiadapter support

- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schoc

i2c, soft-i2c: switch to new multibus/multiadapter support

- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>

show more ...

board/p1010rdb:Add NAND boot support using new SPL format

- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
- remove nand_spl support for P1010RDB

board/p1010rdb:Add NAND boot support using new SPL format

- defines constants
- Add spl_minimal.c to initialise DDR
- update TLB entries as per NAND boot
- remove nand_spl support for P1010RDB

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

show more ...

powerpc/mpc85xx:No NOR boot, do not compile IFC errata A003399

IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.

Signed-off-by

powerpc/mpc85xx:No NOR boot, do not compile IFC errata A003399

IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

show more ...

pci: introduce CONFIG_PCI_INDIRECT_BRIDGE option

The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.

Introdu

pci: introduce CONFIG_PCI_INDIRECT_BRIDGE option

The pci_indirect.c file is always compiled when
CONFIG_PCI is defined although the indirect PCI
bridge support is not needed by every board.

Introduce a new CONFIG_PCI_INDIRECT_BRIDGE
config option and only compile indirect PCI
bridge support if this options is enabled.

Also add the new option into the configuration
files of the boards which needs that.

Compile tested for powerpc, x86, arm and nds32.
MAKEALL results:

powerpc:
--------------------- SUMMARY ----------------------------
Boards compiled: 641
Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB )
----------------------------------------------------------
Note: the warnings for ELPPC and MPC8323ERDB are present even
without the actual patch.

x86:
--------------------- SUMMARY ----------------------------
Boards compiled: 1
----------------------------------------------------------

arm:
--------------------- SUMMARY ----------------------------
Boards compiled: 311
----------------------------------------------------------

nds32:
--------------------- SUMMARY ----------------------------
Boards compiled: 3
----------------------------------------------------------

Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

show more ...

Merge samsung, imx, tegra into u-boot-arm/master

This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manua

Merge samsung, imx, tegra into u-boot-arm/master

This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.

show more ...

Merge remote-tracking branch 'u-boot/master' into u-boot-arm-merged

Conflicts:
README
arch/arm/cpu/armv7/exynos/clock.c
board/samsung/universal_c210/universal.c
drivers/misc/Makefile
drivers/po

Merge remote-tracking branch 'u-boot/master' into u-boot-arm-merged

Conflicts:
README
arch/arm/cpu/armv7/exynos/clock.c
board/samsung/universal_c210/universal.c
drivers/misc/Makefile
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/seaboard.h

show more ...