Merge git://git.denx.de/u-boot-mpc85xx

net: phy: marvell: Fix init function for m88e1145

Commit a058052c changed the generic phy_reset() to clear all bits in
BMCR. This inevitably clears the ANEG bit. m88e1145 requires any
change to ANEG

net: phy: marvell: Fix init function for m88e1145

Commit a058052c changed the generic phy_reset() to clear all bits in
BMCR. This inevitably clears the ANEG bit. m88e1145 requires any
change to ANEG bit to be followed by a software reset. This seems to
be different from other PHYs. Implement read-modify-write procedure
for this PHY init.

Signed-off-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge git://git.denx.de/u-boot-net

net: phy: marvell 88e151x: Fix handling of RGMII interface types

The 88E1518 code is programming the wrong registers for rgmii-id,
rgmii-txid and rgmii-rxid interfaces.

Since the PHY defaults to rg

net: phy: marvell 88e151x: Fix handling of RGMII interface types

The 88E1518 code is programming the wrong registers for rgmii-id,
rgmii-txid and rgmii-rxid interfaces.

Since the PHY defaults to rgmii-id, it would appear that the code
was previously only used with sgmii and rgmii-id interfaces.

Tested on 88E1512 PHY in rgmii-id mode which is from the same family
as 88E1518.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-net

net: phy: Improve the Marvell 151x constants

Use some constants for the phy configuration instead of so many magic
numbers.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Marvell: Use phy_interface_is_rgmii helper function

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberg

net: phy: Marvell: Use phy_interface_is_rgmii helper function

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

net: phy: Add support for Marvell M88E1512

This device also works with the 88E1518 code, so we just adjust
the UID mask accordingly.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-b

net: phy: Add support for Marvell M88E1512

This device also works with the 88E1518 code, so we just adjust
the UID mask accordingly.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

net: phy: Fix mask so that we can identify Marvell 88E1518

The mask for the 88E1510 meant that the 88E1518 code would never be
used.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewe

net: phy: Fix mask so that we can identify Marvell 88E1518

The mask for the 88E1510 meant that the 88E1518 code would never be
used.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

net: phy: Support Marvell 88E1680

Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-o

net: phy: Support Marvell 88E1680

Add support for Marvell 88E1680 Integrated Octal
10/100/1000 Mbps Energy Efficient Ethernet Transceiver.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://git.denx.de/u-boot-dm

net: phy: marvell: Add a missing errno.h header

This corrects a build error on zynqmp.

Signed-off-by: Simon Glass <sjg@chromium.org>

net: phy: marvell: Do not reset 88e1310 after autoneg

Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of

net: phy: marvell: Do not reset 88e1310 after autoneg

Commit a058052c "net: phy: do not read configuration register on reset",
changes the behaviour of the phy_reset function such that the state of
the BMCR register is not preserved during reset.

Change the config function for the m88e1310 so that it does not do a
reset after configuring auto-negotiation.

Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze

phy: marvell: Do not reset phy after negotiation

The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c358c3ecf5f394ff37def6a45eb26768c)
was causing regression on zynq zc7

phy: marvell: Do not reset phy after negotiation

The patch
"net: phy: do not read configuration register on reset"
(sha1: a058052c358c3ecf5f394ff37def6a45eb26768c)
was causing regression on zynq zc702 board where Marwell 88e1118
phy was resetted after negotiation was setup.
Phy reset is done pretty early in phy_connect_dev() and doens't need to
be called again in phy code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

net: phy: Handle phy_startup() error codes properly

Propagate error code from genphy_update_link() to phy startup().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <

net: phy: Handle phy_startup() error codes properly

Propagate error code from genphy_update_link() to phy startup().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

show more ...

phy: Return correct error code when timeout happens

Return -ETIMEDOUT if timeout happens.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stephen Warren <swarren@nvidia.com>

net: phy: marvell: Fix problem with phy_reset() clearing BMCR

With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit

net: phy: marvell: Fix problem with phy_reset() clearing BMCR

With commit a058052c [net: phy: do not read configuration register on
reset], phy_reset() will clear the BMCR register. Resulting in bit 12
being cleared (A/N enable). This leads to autonegotiation link problems,
at least on the Marvell Armada ClearFog board. I suspect that other
boards using this driver will be affected as well.

At the of m88e1111s_config(), phy_reset() is called. This is not needed
for the PHY to load the changed configuration, as phy_reset() is called
a few lines before already. So lets call genphy_restart_aneg() here
instead to start the AN correctly.

Tested on clearfog.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

net: phy: marvell: Call phy_reset() where possible

Instead of coding the soft PHY reset function multiple times in marvell.c,
lets call the common phy_reset() function from phy.c.

Signed-off-by: St

net: phy: marvell: Call phy_reset() where possible

Instead of coding the soft PHY reset function multiple times in marvell.c,
lets call the common phy_reset() function from phy.c.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-net

net: Add support for Marvell 88E1510 PHY

Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.

Signed-off-by: Clemens Gruber <clemens.gru

net: Add support for Marvell 88E1510 PHY

Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

net: Improve 88E151x PHY initialization

- The EEE fixup magic should also be enabled for RGMII
- Improved comments

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <j

net: Improve 88E151x PHY initialization

- The EEE fixup magic should also be enabled for RGMII
- Improved comments

Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

Merge git://git.denx.de/u-boot-ti