Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
add

sunxi: Select CONFIG_OF_BOARD_SETUP from arch/arm/Kconfig

Always select OF_BOARD_SETUP on sunxi, rather then having it in almost
all our defconfigs. This also fixes it missing from some recently
added defconfigs.

This commit also modifies our ft_board_setup() to not cause warnings
when CONFIG_VIDEO_DT_SIMPLEFB is not set, since we will now always
build it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Turn satapwr on from board_init

There are 2 reasons for doing this:

1) The main reason for doing this is to move it outside of
board/sunxi/ahci.c, so that it can be used on boards which u

sunxi: Turn satapwr on from board_init

There are 2 reasons for doing this:

1) The main reason for doing this is to move it outside of
board/sunxi/ahci.c, so that it can be used on boards which use
a usb<->sata chip too;
2) While doing this I realized that doing it from board_init also meant
doing it much earlier. Some printf get_timer(0) calls show that the
time between board_init() and scsi_init() is more then 600 ms,
so we can drop the mdelay(500)

While at it also drop the printf("SUNXI SCSI INIT\n") AHCI init is
noisy enough by itself.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work i

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: block: Rename device number member dev to devnum

This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.

Signed-off-by: Simon Glass <sjg@chromium.org

dm: block: Rename device number member dev to devnum

This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: power: add support for sy8106a driver

SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage t

sunxi: power: add support for sy8106a driver

SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.

This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: power: axp818: Enable support for ALDOs

Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boa

sunxi: power: axp818: Enable support for ALDOs

Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

power: axp: merge separate DLDO functions into 1

Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are cont

power: axp: merge separate DLDO functions into 1

Instead of one function for each DLDO regulator, make 1 function that
takes an extra "index". Since the control bits for the DLDO regulators
are contiguous, this makes the function very simple. This removes a lot
of duplicate code.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

sunxi: Add support for the I2C controller which is part of the PRCM

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@red

sunxi: Add support for the I2C controller which is part of the PRCM

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs

Signed-off-by: Heiko Schocher <hs@denx.de>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: power: enabled support for axp818

Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewe

sunxi: power: enabled support for axp818

Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

sunxi: power: Unify axp pmic function names

Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simpl

sunxi: power: Unify axp pmic function names

Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: power: Make all voltages configurable through Kconfig

On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with

sunxi: power: Make all voltages configurable through Kconfig

On boards with axp221/223 pmic-s we already allow configuring most
voltages. Make the Kconfig options for these also apply to boards with
axp152 / axp209 pmic-s and extend them to configure all voltages.

The Kconfig defaults are chosen so that this commit does not introduce any
functional changes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge remote-tracking branch 'u-boot/master'

sunxi: retrieve FEL-provided values to environment variables

This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and th

sunxi: retrieve FEL-provided values to environment variables

This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.

misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().

The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI

We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a

sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXI

We eventually want to add full nand support, since it makes no sense
to build SPL with nand support and u-boot without, or the other way
around, a single option will suffice.

Renaming the Kconfig option now makes things easier when we add full
nand support in the future.

The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an
"ifdef CONFIG_SPL_BUILD" block in the Makefile.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi_nand_spl: Add support for sun4i and sun5i SoCs

Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.

Note this patch also muxes GPC7 to th

sunxi_nand_spl: Add support for sun4i and sun5i SoCs

Other then having a few less chip-select lines the nand controller
on sun4i, sun5i and sun7i is identical.

Note this patch also muxes GPC7 to the NAND on sun7i where as before
it was not muxed this way. GPC7 is a standard NAND pin, so it should
always be muxed to the NAND when in use.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi_nand_spl: Make sure the DMA controller is enabled

We use DMA for nand data transfers in the SPL, so make sure the DMA
controller is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>

sunxi_nand_spl: Make sure the DMA controller is enabled

We use DMA for nand data transfers in the SPL, so make sure the DMA
controller is enabled.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary

Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.

Signed-off-by: Hans de G

sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessary

Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are
actually using the nand.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...