pxa: add support for D- and I- caches

Tested with OHCI and pxafb drivers - no issues found

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>

pxa: start.S: enable SRAM clock

SRAM is used for early stack, but kernel disables its clock on suspend.
Re-enable SRAM clock on startup, otherwise u-boot crashes on resume from suspend.

Signed-off-

pxa: start.S: enable SRAM clock

SRAM is used for early stack, but kernel disables its clock on suspend.
Re-enable SRAM clock on startup, otherwise u-boot crashes on resume from suspend.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>

show more ...

arm: Add support for HYP mode and LPAE page tables

We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.

Some boards however (like the RPi2) run

arm: Add support for HYP mode and LPAE page tables

We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.

Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.

So this patch introduces support for both long descriptor PTEs and HYP mode
registers.

Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...

ARM: OMAP5/DRA7: Expose do_set_iodelay

do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: To

ARM: OMAP5/DRA7: Expose do_set_iodelay

do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: OMAP5/DRA7: Split iodelay functionality into sub steps

Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier

ARM: OMAP5/DRA7: Split iodelay functionality into sub steps

Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.

While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA72: sdram: Update sdram ext phy configuration for SR2.0

Based on data from EMIF configuration tool 1.1.1.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0

Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been

ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0

Based on data from EMIF configuration tool 1.1.1. Expected update for
CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has
been incorporated as well.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

ARM: DRA72x: Add support for detection of SR2.0

Add support for detection of SR2.0 version of DRA72x family of
processors.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <

ARM: DRA72x: Add support for detection of SR2.0

Add support for detection of SR2.0 version of DRA72x family of
processors.

Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

imx: mx7d: move MX7D to Kconfig entry

If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"sele

imx: mx7d: move MX7D to Kconfig entry

If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX7D" to boards using i.MX7 Dual.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

imx: mx6sx: move MX6SX to Kconfig entry

If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"s

imx: mx6sx: move MX6SX to Kconfig entry

If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS
will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to
"select MX6SX" to boards using i.MX6 SoloX.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

arm: mx6: Add CCV xPress board support

This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (w

arm: mx6: Add CCV xPress board support

This patch add support for the CCV xPress board which is equipped
with the i.MX6UL. And provides the following interfaces:

- 128MiB DDR
- UART
- I2C
- eMMC (with booting)
- Ethernet
- USB

This patch adds two build targets. One with and one without SPL. The
non-SPL version is used for loading U-Boot via USB (imx_usb_loader).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

warp7: Add initial support

Add the basic support for Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-ne

warp7: Add initial support

Add the basic support for Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

show more ...

mx27: 16-bit wide watchdog registers

Make the watchdog registers 16-bit wide, as they are according to TRM.

Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Reviewed-by: Fabio E

mx27: 16-bit wide watchdog registers

Make the watchdog registers 16-bit wide, as they are according to TRM.

Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

show more ...

arm: imx6: Switch DDR3 calibration to wait_for_bit()

Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit()
to generic implementation of wait_for_bit().

Signed-off-by: Marek Vasut

arm: imx6: Switch DDR3 calibration to wait_for_bit()

Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit()
to generic implementation of wait_for_bit().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>

show more ...

imx: print ARM clock for clocks command

Default print ARM clock for clocks command.
Test on i.MX6UL 14x14 evk board:
"
=> clocks
PLL_SYS 792 MHz
PLL_BUS 528 MHz
PLL_OTG 480 M

imx: print ARM clock for clocks command

Default print ARM clock for clocks command.
Test on i.MX6UL 14x14 evk board:
"
=> clocks
PLL_SYS 792 MHz
PLL_BUS 528 MHz
PLL_OTG 480 MHz
PLL_NET 50 MHz

ARM 396000 kHz
"

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ul configure the PMIC_STBY_REQ pin as open drain

Configure the PMIC_STBY_REQ pin as open drain 100K according
to the design team's requirement for the PMIC_STBY_REQ pin
for i.MX 6UltraLite T

imx: mx6ul configure the PMIC_STBY_REQ pin as open drain

Configure the PMIC_STBY_REQ pin as open drain 100K according
to the design team's requirement for the PMIC_STBY_REQ pin
for i.MX 6UltraLite TO1.0.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>

show more ...

imx: mx6ul: skip setting ahb rate

To i.MX6UL, default ARM rate and AHB rate is 396M and 198M,
no need to set them.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>

imx: mx6: Fix incorrect clear mmdc_ch0 handshake mask

Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register
the bit[17] for mmdc_ch0 is reserved and its proper state should be 1.
When

imx: mx6: Fix incorrect clear mmdc_ch0 handshake mask

Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register
the bit[17] for mmdc_ch0 is reserved and its proper state should be 1.
When clear this bit, the periph_clk_sel cannot be set and that
CDHIPR[periph_clk_sel_busy] handshake never clears.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

sunxi: A83T: fix 32bit overflow warning

In mctl_channel_init, (0x50<<26) which overflows 32bit.
It was supposed to be 0x50<<16,corrected now.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed

sunxi: A83T: fix 32bit overflow warning

In mctl_channel_init, (0x50<<26) which overflows 32bit.
It was supposed to be 0x50<<16,corrected now.

Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work i

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

cpu_eth_init is no longer called for dm enabled eth drivers, this
was causing the sunxi gmac eth controller to no longer work in u-boot.

This commit fixes this by calling the clock, reset and pinmux setup
function from s_init() and enabling the phy power pin (if any) from
board_init().

The enabling of phy power cannot be done from s_init because it uses dm
and dm is not ready yet at this point.

Note that the mdelay is dropped as the phy gets enabled much earlier
now, so it is no longer needed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Karsten Merker <merker@debian.org>
Tested-by: Michael Haas <haas@computerlinguist.org>

show more ...

sunxi: Add support for USB vbus pin for USB3

The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@h

sunxi: Add support for USB vbus pin for USB3

The H3 has USB0 - USB3, add support for having a USB vbus pin for USB3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Fix clock_twi_onoff for sun9i

Fix a copy and paste error which caused us to use the uart rather then
the twi reset bits in clock_twi_onoff for sun9i.

Signed-off-by: Hans de Goede <hdegoede@r

sunxi: Fix clock_twi_onoff for sun9i

Fix a copy and paste error which caused us to use the uart rather then
the twi reset bits in clock_twi_onoff for sun9i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Fix clock_twi_onoff for sun8i-a83

clock_sun8i_a83.c did not contain a clock_twi_onoff implementation
at all, this is fixed by moving the clock_sun6i.c implementation,
which is correct for the

sunxi: Fix clock_twi_onoff for sun8i-a83

clock_sun8i_a83.c did not contain a clock_twi_onoff implementation
at all, this is fixed by moving the clock_sun6i.c implementation,
which is correct for the a83 too, to a shared location.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: Fix clock_twi_onoff for sun6i

The clock_sun6i.c implementation was not deasserting the reset for
the regular i2c controllers, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@r

sunxi: Fix clock_twi_onoff for sun6i

The clock_sun6i.c implementation was not deasserting the reset for
the regular i2c controllers, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

sunxi: A23: Fix some revisions needing a different magic sram poke

I've had this one a23 tablet which would not boot and I've finally
figured out what the problem is by looking at the released boot0

sunxi: A23: Fix some revisions needing a different magic sram poke

I've had this one a23 tablet which would not boot and I've finally
figured out what the problem is by looking at the released boot0 code,
it seems the magic sram controller poke which we need to do in s_init()
depends on the revision of the a23.

Specifically this change is needed to get the A23 SoC I have with the
following serial to boot: "E6071AB 26Y7".

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...