| c655b816 | 16-Dec-2013 |
Otavio Salvador <otavio@ossystems.com.br> |
ARM: mx6: Allow enablement of FEC Anatop based clock for all MX6
The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code ou
ARM: mx6: Allow enablement of FEC Anatop based clock for all MX6
The enable_fec_anatop_clock method should be available for all MX6
variant as it is not MX6 SoloLite specific. This moves the code out of
the #ifdef/#endif and we make it conditional to CONFIG_FEC_MXC
instead.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
show more ...
|
| 02229827 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Disable VDDPU regulator
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: J
mx6: soc: Disable VDDPU regulator
As U-boot does not use GPU/VPU peripherals, shutdown the VDDPU regulator
in order to save power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| 39f0ac93 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Add the required LDO ramp up delay
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.
Also, as the timer is still not available when arc
mx6: soc: Add the required LDO ramp up delay
When changing LDO voltages we need to wait for the required amount of time
for the voltage to settle.
Also, as the timer is still not available when arch_cpu_init() is called, we
need to call it later at board_postclk_init() phase.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| 3d622b78 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Introduce set_ldo_voltage()
Introduce set_ldo_voltage() so that all three LDO regulators can be configured.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> |
| 7e5e8c94 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Set the VDDSOC at 1.175 V
mx6 datasheet specifies that the minimum VDDSOC at 792 MHz is 1.15 V.
Add a 25 mV margin and set it to 1.175V.
This also matches the VDDSOC voltages for 792MHz o
mx6: soc: Set the VDDSOC at 1.175 V
mx6 datasheet specifies that the minimum VDDSOC at 792 MHz is 1.15 V.
Add a 25 mV margin and set it to 1.175V.
This also matches the VDDSOC voltages for 792MHz operation that the kernel configures:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/cpu_op-mx6.c?h=imx_3.0.35_4.1.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| e113fd19 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Clear the LDO ramp values up prior to setting the LDO voltages
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default va
mx6: soc: Clear the LDO ramp values up prior to setting the LDO voltages
Since ROM may modify the LDO ramp up time according to fuse setting,
it is safer to reset the ramp up field to its default value of 00:
00: 64 cycles of 24MHz clock;
01: 128 cycles of 24MHz clock;
02: 256 cycles of 24MHz clock;
03: 512 cycles of 24MHz clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| fc740648 | 26-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: soc: Staticize set_vddsoc()
set_vddsoc() is not used anywhere else, so make it static.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> |
| 5af4a4f7 | 26-Dec-2013 |
Rajeshwari Birje <rajeshwari.s@samsung.com> |
Exynos5420: Add support for 5420 in pinmux and gpio
Adds code in pinmux and gpio framework to support Exynos5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Aksh
Exynos5420: Add support for 5420 in pinmux and gpio
Adds code in pinmux and gpio framework to support Exynos5420.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| f3d7c2fe | 26-Dec-2013 |
Rajeshwari Birje <rajeshwari.s@samsung.com> |
Exynos5420: Add DDR3 initialization for 5420
This patch intends to add DDR3 initialization code for Exynos5420.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shi
Exynos5420: Add DDR3 initialization for 5420
This patch intends to add DDR3 initialization code for Exynos5420.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| 060c227a | 26-Dec-2013 |
Rajeshwari Birje <rajeshwari.s@samsung.com> |
Exynos5420: Add clock initialization for 5420
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420
Signed-off-by: Rajeshwari S S
Exynos5420: Add clock initialization for 5420
This patch adds code for clock initialization and clock settings
of various IP's and controllers, required for Exynos5420
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
show more ...
|
| b5e01eec | 10-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enab
ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
show more ...
|
| d3daba10 | 10-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief descr
ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
show more ...
|
| 965de8b9 | 10-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating
ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
show more ...
|
| cf04d032 | 10-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is lock
ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
show more ...
|
| 0d54cb92 | 10-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: AM43xx: Select clk source for Timer2
Selecting the Master osc clk as Timer2 clock source.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> |
| d627eefc | 18-Dec-2013 |
Albert ARIBAUD <albert.u.boot@aribaud.net> |
Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master' |
| 3346cbb8 | 13-Nov-2013 |
Alban Bedel <alban.bedel@avionic-design.de> |
ARM: tegra: support SKU b1 of Tegra30
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.sch
ARM: tegra: support SKU b1 of Tegra30
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| 4475c775 | 01-Oct-2013 |
Thierry Reding <thierry.reding@gmail.com> |
Tegra114: Do not program CPCON field for PLLX
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom
Tegra114: Do not program CPCON field for PLLX
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| 44de8e22 | 23-Sep-2013 |
Jimmy Zhang <jimmzhang@nvidia.com> |
Tegra114: Fix PLLX M, N, P init settings
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordin
Tegra114: Fix PLLX M, N, P init settings
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
show more ...
|
| 23f00caf | 17-Dec-2013 |
Sergei Ianovich <ynvich@gmail.com> |
ARM: pxa: prevent PXA270 occasional reboot freezes
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
ARM: pxa: prevent PXA270 occasional reboot freezes
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs.
We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
show more ...
|
| ebaf6b26 | 13-Nov-2013 |
Frank Li <Frank.Li@freescale.com> |
imx6: fix random hang when download by usb
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache
Signed-off-by: Huang yongcai <b20788@freescale.com>
Sign
imx6: fix random hang when download by usb
ROM did not invalidate L1 cache when download by usb
Need invalidate L1 cache before enable cache
Signed-off-by: Huang yongcai <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
show more ...
|
| 89cfd0f5 | 03-Dec-2013 |
Fabio Estevam <fabio.estevam@freescale.com> |
mx6: clock: Fix the calculation of PLL_ENET frequency
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:
"Controls the freq
mx6: clock: Fix the calculation of PLL_ENET frequency
According to the mx6 quad reference manual, the DIV_SELECT field of register
CCM_ANALOG_PLL_ENETn has the following meaning:
"Controls the frequency of the ethernet reference clock.
- 00 - 25MHz
- 01 - 50MHz
- 10 - 100MHz
- 11 - 125MHz"
Current logic does not handle the 25MHz case correctly, so fix it.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
show more ...
|
| 49a90e29 | 05-Dec-2013 |
Tom Rini <trini@ti.com> |
ARM:PXA: Correct tick_to_time / us_to_tick to use lldiv
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Marek Vasut <marex@denx.de> |
| e83bab84 | 05-Dec-2013 |
Tom Rini <trini@ti.com> |
ARM:zynq: Correct __udelay to use lldiv
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Tom Rini <trini@ti.com> |
| d2c7074b | 12-Dec-2013 |
Lokesh Vutla <lokeshvutla@ti.com> |
ARM: OMAP5: clocks: Update MPU settings for OPP_NOM
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MH
ARM: OMAP5: clocks: Update MPU settings for OPP_NOM
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
show more ...
|