imx: mx7ulp: add iomux driver to support IOMUXC0 and IOMUXC1

Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while

imx: mx7ulp: add iomux driver to support IOMUXC0 and IOMUXC1

Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>

show more ...

imx: mx7ulp: Add mx7ulp to Kconfig

i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.

Signed-off-by:

imx: mx7ulp: Add mx7ulp to Kconfig

i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

armv7m: Add SysTick timer driver

The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.

The number of reference clock tick

armv7m: Add SysTick timer driver

The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.

The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>

show more ...

arm: omap3: Bring back ARM errata workaround 725233

The workaround for ARM errata 725233 had been lost since
commit 45bf05854bc94e (armv7: adapt omap3 to the new cache
maintenance framework). Bring

arm: omap3: Bring back ARM errata workaround 725233

The workaround for ARM errata 725233 had been lost since
commit 45bf05854bc94e (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

armv8: fsl-lsch2: add workaround for erratum A-010635

Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC

armv8: fsl-lsch2: add workaround for erratum A-010635

Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.

Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

armv8: layerscape: Update early MMU for DDR after initialization

In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updat

armv8: layerscape: Update early MMU for DDR after initialization

In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: mmu: Add a function to change mapping attributes

Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
proce

armv8: mmu: Add a function to change mapping attributes

Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: ls2080a: Drop early MMU for SPL build

Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-c

armv8: ls2080a: Drop early MMU for SPL build

Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: layerscape: Fix the sequence of changing MMU table

This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potenti

armv8: layerscape: Fix the sequence of changing MMU table

This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: layerscape: Update MMU mapping with actual DDR size

Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.

Signed-off-b

armv8: layerscape: Update MMU mapping with actual DDR size

Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: layerscape: Rewrite memory reservation

For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit a

armv8: layerscape: Rewrite memory reservation

For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.

Signed-off-by: York Sun <york.sun@nxp.com>

show more ...

armv8: ls2080a: Move CONFIG_SYS_MC_RSV_MEM_ALIGN to Kconfig

Use Kconfig option instead of config macro in header file.

Signed-off-by: York Sun <york.sun@nxp.com>

armv8: ls2080a: Move CONFIG_FSL_MC_ENET to Kconfig

Use Kconfig option instead of config macro in header file.
Clean up existing usage.

Signed-off-by: York Sun <york.sun@nxp.com>

armv8: Add global variable resv_ram

Use gd->arch.resv_ram to track reserved memory allocation.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ARM: Migrate errata to Kconfig

This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a

ARM: Migrate errata to Kconfig

This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it

flash: complete CONFIG_SYS_NO_FLASH move with renaming

We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
configs/ls1046aqds_defconfig
configs/ls1046aqds_nand_defconfig
configs/ls1046aqds_qspi_defconfig

Merge git://git.denx.de/u-boot-fsl-qoriq

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
configs/ls1046aqds_defconfig
configs/ls1046aqds_nand_defconfig
configs/ls1046aqds_qspi_defconfig
configs/ls1046aqds_sdcard_ifc_defconfig
configs/ls1046aqds_sdcard_qspi_defconfig
configs/ls1046ardb_emmc_defconfig
configs/ls1046ardb_qspi_defconfig
configs/ls1046ardb_sdcard_defconfig

show more ...

arch: arm: update the IFC IP input clock

IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP o

arch: arm: update the IFC IP input clock

IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.

Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-imx