Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
Makefile
drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver")

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
Makefile
drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.

show more ...

i2c, bootcount: add support for bootcounter on i2c devices

add support for bootcounter on an i2c device. And add a
README for all bootcounter options.

Signed-off-by: Heiko Schocher <hs@denx.de>

doc: README: Correct file name of signature verification documentation

Signed-off-by: Detlev Zundel <dzu@denx.de>

README: document CONFIG_CMD_FS_GENERIC

This enables generic filesystem commands such as load and ls, which
automatically work with multiple filesystem types, without having to
be told which is prese

README: document CONFIG_CMD_FS_GENERIC

This enables generic filesystem commands such as load and ls, which
automatically work with multiple filesystem types, without having to
be told which is present, unlike e.g. ext2load, fatls.

Signed-off-by: Stephen Warren <swarren@nvidia.com>

show more ...

Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-arm

ARM: IXP: Remove the IXP architecture support

The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Mic

ARM: IXP: Remove the IXP architecture support

The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>

show more ...

Merge branch 'clk' of git://www.denx.de/git/u-boot-microblaze

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

common: Add new clk command

Command provides just dump subcommand for showing clock
frequencies in a soc.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.

common: Add new clk command

Command provides just dump subcommand for showing clock
frequencies in a soc.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

driver/ifc:Change accessor function to take care of endianness

IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.

S

driver/ifc:Change accessor function to take care of endianness

IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.

So update acessor functions with common IFC acessor functions to take care
both type of endianness.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

powerpc:Rename CONFIG_PBLRCW_CONFIG & CONFIG_SYS_FSL_PBL_PBI

Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.

Also add their details in README.

Signed-off-by: Prabhakar Kushwaha <prabhakar@fr

powerpc:Rename CONFIG_PBLRCW_CONFIG & CONFIG_SYS_FSL_PBL_PBI

Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG.

Also add their details in README.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

sf: Add CONFIG_SF_DUAL_FLASH

This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xi

sf: Add CONFIG_SF_DUAL_FLASH

This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

powerpc/mpc85xx: Add support for single source clocking

Single-source clocking is new feature introduced in T1040.
In this mode, a single differential clock is supplied to the
DIFF_SYSCLK_P/N inputs

powerpc/mpc85xx: Add support for single source clocking

Single-source clocking is new feature introduced in T1040.
In this mode, a single differential clock is supplied to the
DIFF_SYSCLK_P/N inputs to the processor, which in turn is
used to supply clocks to the sysclock, ddrclock and usbclock.

So, both ddrclock and syclock are driven by same differential
sysclock in single-source clocking mode whereas in normal clocking
mode, generally separate DDRCLK and SYSCLK pins provides
reference clock for sysclock and ddrclock

DDR_REFCLK_SEL rcw bit is used to determine DDR clock source
-If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in
normal clocking mode by DDR_Reference clock

-If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in
single source clocking mode by DIFF_SYSCLK

Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>

show more ...

board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by:

board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>

show more ...

Add dumpimage, a tool to extract data from U-Boot images

Given a multi-file image created through the mkimage's -d option:

$ mkimage -A x86 -O linux -T multi -n x86 -d vmlinuz:initrd.img:System.m

Add dumpimage, a tool to extract data from U-Boot images

Given a multi-file image created through the mkimage's -d option:

$ mkimage -A x86 -O linux -T multi -n x86 -d vmlinuz:initrd.img:System.map \
multi.img

Image Name: x86
Created: Thu Jul 25 10:29:13 2013
Image Type: Intel x86 Linux Multi-File Image (gzip compressed)
Data Size: 13722956 Bytes = 13401.32 kB = 13.09 MB
Load Address: 00000000
Entry Point: 00000000
Contents:
Image 0: 4040128 Bytes = 3945.44 kB = 3.85 MB
Image 1: 7991719 Bytes = 7804.41 kB = 7.62 MB
Image 2: 1691092 Bytes = 1651.46 kB = 1.61 MB

It is possible to perform the innverse operation -- extracting any file from
the image -- by using the dumpimage's -i option:

$ dumpimage -i multi.img -p 2 System.map

Although it's feasible to retrieve "data files" from image through scripting,
the requirement to embed tools such 'dd', 'awk' and 'sed' for this sole purpose
is cumbersome and unreliable -- once you must keep track of file sizes inside
the image. Furthermore, extracting data files using "dumpimage" tool is faster
than through scripting.

Signed-off-by: Guilherme Maciel Ferreira <guilherme.maciel.ferreira@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
board/samsung/trats2/trats2.c
include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard

Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compul

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard

Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-i2c

i2c: samsung: register i2c busses for Exynso5420 and Exynos5250

This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function

i2c: samsung: register i2c busses for Exynso5420 and Exynos5250

This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels

Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

Driver/DDR: Add Freescale DDR driver for ARM

Make PowerPC specific code conditional so ARM SoCs can reuse
this driver. Add DDR3 driver for ARM.

Signed-off-by: York Sun <yorksun@freescale.com>