Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is pr

Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is present
plat/marvell: a8k: move efuse definitions to separate header
plat/marvell/armada: fix TRNG return SMC handling
drivers: marvell: comphy: add rx training on 10G port
plat/marvell/armada: postpone MSS CPU startup to BL31 stage
plat: marvell: armada: a8k: Fix LD selector mask
plat/marvell/armada: allow builds without MSS support
drivers: marvell: misc-dfx: extend dfx whitelist
drivers: marvell: add support for secure read/write of dfx register-set
ddr_phy: use smc calls to access ddr phy registers
drivers: marvell: thermal: use dedicated function for thermal SiPs
drivers: marvell: add thermal sensor driver and expose it via SIP service
fix: plat: marvell: fix MSS loader for A8K family

show more ...

plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes s

plat/marvell/armada: postpone MSS CPU startup to BL31 stage

Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.

Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>

show more ...

plat/marvell/armada: allow builds without MSS support

Setting MSS_SUPPORT to 0 also removes requirement for SCP_BL2
definition.
Images build with MSS_SUPPORT=0 will not include service CPUs
FW and w

plat/marvell/armada: allow builds without MSS support

Setting MSS_SUPPORT to 0 also removes requirement for SCP_BL2
definition.
Images build with MSS_SUPPORT=0 will not include service CPUs
FW and will not support PM, FC and other features implemented
in these FW images.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Idf301ebd218ce65a60f277f3876d0aeb6c72f105
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/37769
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>

show more ...

Merge changes Ib9c82b85,Ib348e097,I4dc315e4,I58a8ce44,Iebc03361, ... into integration

* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping th

Merge changes Ib9c82b85,Ib348e097,I4dc315e4,I58a8ce44,Iebc03361, ... into integration

* changes:
plat: marvell: armada: a8k: add OP-TEE OS MMU tables
drivers: marvell: add support for mapping the entire LLC to SRAM
plat: marvell: armada: add LLC SRAM CCU setup for AP806/AP807 platforms
plat: marvell: armada: reduce memory size reserved for FIP image
plat: marvell: armada: platform definitions cleanup
plat: marvell: armada: a8k: check CCU window state before loading MSS BL2
drivers: marvell: add CCU driver API for window state checking
drivers: marvell: align and extend llc macros
plat: marvell: a8k: move address config of cp1/2 to BL2
plat: marvell: armada: re-enable BL32_BASE definition
plat: marvell: a8k: extend includes to take advantage of the phy_porting_layer
marvell: comphy: initialize common phy selector for AP mode
marvell: comphy: update rx_training procedure
plat: marvell: armada: configure amb for all CPs
plat: marvell: armada: modify PLAT_FAMILY name for 37xx SoCs

show more ...

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done af

plat: marvell: a8k: move address config of cp1/2 to BL2

The configuration space of each standalone CP was updated in BL31.
Loading FW procedure take places earlier in SCP_BL2.
It needs to be done after access to each CP is provided.
Moving the proper configuration from BL31 to BL2 solves it.

Change-Id: I44cf88dfd4ebf09130544332bfdd3d16ef2674ea
Signed-off-by: Ben Peled <bpeled@marvell.com>

show more ...

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble:

Merge changes I80316689,I23cac4fb,If911e7de,I169ff358,I4e040cd5, ... into integration

* changes:
ddr: a80x0: add DDR 32-bit ECC mode support
ble: ap807: improve PLL configuration sequence
ble: ap807: clean-up PLL configuration sequence
ddr: a80x0: add DDR 32-bit mode support
plat: marvell: mci: perform mci link tuning for all mci interfaces
plat: marvell: mci: use more meaningful name for mci link tuning
plat: marvell: a8k: remove wrong or unnecessary comments
plat: marvell: ap807: enable snoop filter for ap807
plat: marvell: ap807: update configuration space of each CP
plat: marvell: ap807: use correct address for MCIx4 register
plat: marvell: add support for PLL 2.2GHz mode
plat: marvell: armada: make a8k_common.mk and mss_common.mk more generic
marvell: armada: add extra level in marvell platform hierarchy

show more ...

plat: marvell: mci: perform mci link tuning for all mci interfaces

This commit introduces two changes:
- remove hardcoded references to mci0 from the driver
- perform mci optimization for all mci in

plat: marvell: mci: perform mci link tuning for all mci interfaces

This commit introduces two changes:
- remove hardcoded references to mci0 from the driver
- perform mci optimization for all mci interfaces

It fixes performance issues observed on cn9132 CP2.

Change-Id: I4e040cd54ff95c9134035ac89b87d8feb28e9eba
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

plat: marvell: mci: use more meaningful name for mci link tuning

The mci_initialize function name was misleading. The function itself
doesn't initialize MCI in general but performs MCI link tuning f

plat: marvell: mci: use more meaningful name for mci link tuning

The mci_initialize function name was misleading. The function itself
doesn't initialize MCI in general but performs MCI link tuning for
performance improvement.

Change-Id: I13094ad2235182a14984035bbe58013ebde84a7e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

plat: marvell: a8k: remove wrong or unnecessary comments

Change-Id: Id702c070c433f8439faad115830e71b2873ab70a
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

plat: marvell: ap807: update configuration space of each CP

By default all external CPs start with configuration address space set to
0xf200_0000. To overcome this issue, go in the loop and initiali

plat: marvell: ap807: update configuration space of each CP

By default all external CPs start with configuration address space set to
0xf200_0000. To overcome this issue, go in the loop and initialize the
CP one by one, using temporary window configuration which allows to access
each CP and update its configuration space according to decoding
windows scheme defined for each platform.

In case of cn9130 after this procedure bellow addresses will be used:
CP0 - f2000000
CP1 - f4000000
CP2 - f6000000

When the re-configuration is done there is need to restore previous
decoding window configuration(init_io_win).

Change-Id: I1a652bfbd0bf7106930a7a4e949094dc9078a981
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
pla

marvell: armada: add extra level in marvell platform hierarchy

This commit is a preparation for upcoming support for OcteonTX and
OcteonTX2 product families. Armada platform related files (docs,
plat, include/plat) are moved to the new "armada" sub-folder.

Change-Id: Icf03356187078ad6a2e56c9870992be3ca4c9655
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>

show more ...