feat(auth): compare platform and certificate ROTPK for authentication

Compared the full ROTPK with the ROTPK obtained from the certificate
when the platform supports full ROTPK instead of hash of RO

feat(auth): compare platform and certificate ROTPK for authentication

Compared the full ROTPK with the ROTPK obtained from the certificate
when the platform supports full ROTPK instead of hash of ROTPK.

Additionally, changed the code to verify the ROTPK before relying on
it for signature verification.

Change-Id: I52bb9deb1a1dd5b184d3156bddad14c238692de7
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>

show more ...

fix(rpi3): initialize SD card host controller

Add initial configuration parameters for Rasperry Pi 3's sdhost
controller, and then configure and use those parameters.

This change allows warm reboot

fix(rpi3): initialize SD card host controller

Add initial configuration parameters for Rasperry Pi 3's sdhost
controller, and then configure and use those parameters.

This change allows warm reboots of UEFI on Raspberry Pi 3B+ where
existing code often fails with "unknown error". See discussion at:

https://github.com/pftf/RPi3/issues/24

The basic idea is that some initial configuration parameters
(clock rate, bus width) aren't configured into the hardware before
commands start being sent. I suspect that the particular setting
that matters is the "slow card" bit, but the initial clock setting
also seemed wrong to me.

Change-Id: I526def340def143f23f3422f1fc14c12c937ca7f
Signed-off-by: Rob Newberry <robthedude@mac.com>

show more ...

Merge "fix(scmi): fix compilation error in scmi base" into integration

feat(ethos-n): add separate RO and RW NSAIDs

To be able to further restrict the memory access for the Arm(R)
Ethos(TM)-N NPU, separate read-only and read/write NSAIDs for the
non-protected and prote

feat(ethos-n): add separate RO and RW NSAIDs

To be able to further restrict the memory access for the Arm(R)
Ethos(TM)-N NPU, separate read-only and read/write NSAIDs for the
non-protected and protected memory have been added to the Juno
platform's TZMP1 TZC configuration for the NPU.

The platform definition has been updated accordingly and the NPU driver
will now only give read/write access to the streams that require it.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I5a173500fc1943a5cd406a3b379e1f1f554eeda6

show more ...

feat(ethos-n)!: add protected NPU firmware setup

When the Arm(R) Ethos(TM)-N NPU driver is built with TZMP1 support, the
NPU should use the firmware that has been loaded into the protected
memory by

feat(ethos-n)!: add protected NPU firmware setup

When the Arm(R) Ethos(TM)-N NPU driver is built with TZMP1 support, the
NPU should use the firmware that has been loaded into the protected
memory by BL2. The Linux Kernel NPU driver in the non-secure world is
not allowed to configure the NPU to do this in a TZMP1 build so the SiP
service will now configure the NPU to boot with the firmware in the
protected memory.

BREAKING CHANGE: The Linux Kernel NPU driver can no longer directly
configure and boot the NPU in a TZMP1 build. The API version has
therefore been given a major version bump with this change.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65d00f54b3ade3665d7941e270da7a3dec02281a

show more ...

feat(ethos-n): add stream extends and attr support

The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the address extension and attribute control for the NPU's
streams.

feat(ethos-n): add stream extends and attr support

The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the address extension and attribute control for the NPU's
streams. The non-secure world will still be allowed to read the address
extension for stream0 but non-secure access to all other streams have
been removed.

The API version has been given a minor bump with this change to indicate
the added functionality.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I2b041ca4a0a2b5cd6344a4ae144f75e137c72592

show more ...

feat(ethos-n): add event and aux control support

The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the NPU's event and aux control registers during the SMC
reset call.

feat(ethos-n): add event and aux control support

The SiP service for the Arm(R) Ethos(TM)-N NPU driver will now handle
setting up the NPU's event and aux control registers during the SMC
reset call. The aux control register will no longer be accessible by the
non-secure world.

The API version has been given a minor bump with this change to indicate
the added functionality.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I5b099e25978aa4089c384eb17c5060c5b4eaf373

show more ...

feat(ethos-n): add SMC call to get FW properties

When the Arm(R) Ethos(TM)-N NPU firmware is loaded by BL2 into protected
memory, the Linux kernel NPU driver cannot access the firmware. To still
all

feat(ethos-n): add SMC call to get FW properties

When the Arm(R) Ethos(TM)-N NPU firmware is loaded by BL2 into protected
memory, the Linux kernel NPU driver cannot access the firmware. To still
allow the kernel driver to access some information about the firmware,
SMC calls have been added so it can check compatibility and get the
necessary information to map the firmware into the SMMU for the NPU.

The API version has been given a minor version bump with this change to
indicate the added functionality.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Idb076b7bcf54ed7e8eb39be80114dc1d1c45336d

show more ...

refactor(ethos-n): split up SMC call handling

Doing all the SMC call handling in a single function and using specific
names for the x1-4 parameters is no longer practical for upcoming
additions to t

refactor(ethos-n): split up SMC call handling

Doing all the SMC call handling in a single function and using specific
names for the x1-4 parameters is no longer practical for upcoming
additions to the SiP service. Handling of the different SMC functions
have therefore been split into separate functions.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: If28da8df0f13c449d1fdb2bd9d792d818ec5e1af

show more ...

feat(ethos-n): add NPU firmware validation

When the Arm(R) Ethos(TM)-N NPU driver is built with TZMP1 support, it
will now validate the NPU firmware binary that BL2 is expected to load
into the prot

feat(ethos-n): add NPU firmware validation

When the Arm(R) Ethos(TM)-N NPU driver is built with TZMP1 support, it
will now validate the NPU firmware binary that BL2 is expected to load
into the protected memory location specified by
ARM_ETHOSN_NPU_IMAGE_BASE.

Juno has been updated with a new BL31 memory mapping to allow the SiP
service to read the protected memory that contains the NPU firmware
binary.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I633256ab7dd4f8f5a6f864c8c98a66bf9dfc37f3

show more ...

feat(ethos-n): add check for NPU in SiP setup

The SiP service in the Arm(R) Ethos(TM)-N NPU driver requires that there
is at least one NPU available. If there is no NPU available, the driver
is eith

feat(ethos-n): add check for NPU in SiP setup

The SiP service in the Arm(R) Ethos(TM)-N NPU driver requires that there
is at least one NPU available. If there is no NPU available, the driver
is either used incorrectly or the HW config is incorrect.

To ensure that the SiP service is not incorrectly used, a setup handler
has been added to the service that will validate that there is at least
one NPU available.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I8139a652f265cfc0db4a37464f39f1fb92868e10

show more ...

fix(ethos-n): add workaround for erratum 2838783

To workaround Arm(R) Ethos(TM)-N NPU erratum 2838783, the NPU has been
configured to allow being woken up by both secure and non-secure events
to mak

fix(ethos-n): add workaround for erratum 2838783

To workaround Arm(R) Ethos(TM)-N NPU erratum 2838783, the NPU has been
configured to allow being woken up by both secure and non-secure events
to make sure that an event always wakes up the NPU.

The API version has been given a minor version bump with this change to
indicate that this fix is included.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I429cdd6bf1e633b4dedf2e94af28937dd892a0ba

show more ...

feat(ethos-n): add support to set up NSAID

For the TZC to allow the Arm(R) Ethos(TM)-N NPU to access the buffers
allocated in a protected memory region, it must include the correct
NSAID for that re

feat(ethos-n): add support to set up NSAID

For the TZC to allow the Arm(R) Ethos(TM)-N NPU to access the buffers
allocated in a protected memory region, it must include the correct
NSAID for that region in its transactions to the memory. This change
updates the SiP service to configure the NSAIDs specified by a platform
define. When doing a protected access the SiP service now configures the
NSAIDs specified by the platform define. For unprotected access the
NSAID is set to zero.

Signed-off-by: Rajasekaran Kalidoss <rajasekaran.kalidoss@arm.com>
Signed-off-by: Rob Hughes <robert.hughes@arm.com>
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I3360ef33705162aba5c67670386922420869e331

show more ...

feat(ethos-n): add NPU sleeping SMC call

The non-secure world delegation of the register needed to determine if
the Arm(R) Ethos(TM)-N NPU is active or sleeping will be removed in the
future. In pre

feat(ethos-n): add NPU sleeping SMC call

The non-secure world delegation of the register needed to determine if
the Arm(R) Ethos(TM)-N NPU is active or sleeping will be removed in the
future. In preparation for the change, a new SMC call has been added to
allow the non-secure world to ask the SiP service for the state instead.

A minor API version bump has been done with this change to indicate
support for the new functionality.

Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I1338341be385cf1891f4809efb7083fae6d928bc

show more ...

feat(ethos-n): add reset type to reset SMC calls

Adds a reset type argument for the soft and hard reset SMC calls to
indicate whether to perform a full reset and setup or only halt the
Arm(R) Ethos(

feat(ethos-n): add reset type to reset SMC calls

Adds a reset type argument for the soft and hard reset SMC calls to
indicate whether to perform a full reset and setup or only halt the
Arm(R) Ethos(TM)-N NPU. For use in cases where the NPU will not be
used but must be put into a known state, such as suspending the NPU
as part of power management.

Signed-off-by: Joshua Pimm <joshua.pimm@arm.com>
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I6018af85a28b0e977166ec29d26f04739123140c

show more ...

fix(gicv3): workaround for NVIDIA erratum T241-FABRIC-4

The purpose of this patch is to address the T241 erratum T241-FABRIC-4,
which causes unexpected behavior in the GIC when multiple transactions

fix(gicv3): workaround for NVIDIA erratum T241-FABRIC-4

The purpose of this patch is to address the T241 erratum T241-FABRIC-4,
which causes unexpected behavior in the GIC when multiple transactions
are received simultaneously from different sources. This hardware issue
impacts NVIDIA server platforms that use more than two T241 chips
interconnected. Each chip has support for 320 {E}SPIs.

This issue occurs when multiple packets from different GICs are
incorrectly interleaved at the target chip. The erratum text below
specifies exactly what can cause multiple transfer packets susceptible
to interleaving and GIC state corruption. GIC state corruption can
lead to a range of problems, including kernel panics, and unexpected
behavior.

Erratum documentation:
https://developer.nvidia.com/docs/t241-fabric-4/nvidia-t241-fabric-4-errata.pdf

The workaround is to ensure that MMIO accesses target the GIC on the
socket that holds the data, for example SPI ranges owned by the socket’s
GIC. This ensures that the GIC will not utilize the inter-socket AXI
Stream interface for servicing these GIC MMIO accesses.

This patch updates the functions that use the GICD_In{E} registers to
ensure that the accesses are directed to the chip that owns the SPI,
instead of using the global alias.

Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I04e33ba64eb306bd5fdabb56e63cbe273d8cd632

show more ...

Merge "fix(mmc): remove redundant reset_to_idle call" into integration

fix(scmi): fix compilation error in scmi base

Fix compilation error when scmi base in enabled.
The following compilation error is visible:
drivers/scmi-msg/base.c: In function 'discover_list_protoco

fix(scmi): fix compilation error in scmi base

Fix compilation error when scmi base in enabled.
The following compilation error is visible:
drivers/scmi-msg/base.c: In function 'discover_list_protocols':
include/lib/utils_def.h:70:20: error: comparison of distinct
pointer types lacks a cast [-Werror]
70 | (void)(&_x == &_y); \
| ^~
drivers/scmi-msg/base.c:154:25: note: in expansion of macro 'MIN'
154 | count = MIN(count - a2p->skip,
msg->out_size - sizeof(p2a));

Change-Id: I79e60d4bc9c4f6e78a76099a36ebf4fe5212a7d1
Signed-off-by: Michal Simek <michal.simek@amd.com>

show more ...

Merge "feat(ufs): adds timeout and error handling" into integration

Merge "fix(nxp-drivers): use semicolon instead of comma" into integration

fix(nxp-drivers): use semicolon instead of comma

Use semicolon insted of comma at the end of line.

Change-Id: Id820f4419fdd7cf522fd8bb07395789d25f40c2e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>

feat(ufs): adds timeout and error handling

Adds a common function to poll for interrupt status which reports errors
and returns error codes

Signed-off-by: Anand Saminathan <anans@google.com>
Change

feat(ufs): adds timeout and error handling

Adds a common function to poll for interrupt status which reports errors
and returns error codes

Signed-off-by: Anand Saminathan <anans@google.com>
Change-Id: Ie5df036dc979e984871de4ae7e974b994296ca4c

show more ...

Merge "fix(rss): fix msg deserialization bugs in comms" into integration

style: remove useless trailing semicolon and line continuations

found using checkpatch.pl[1]

[1]: https://review.coreboot.org/plugins/gitiles/coreboot/+/refs/heads/master/util/lint/checkpatch.pl

S

style: remove useless trailing semicolon and line continuations

found using checkpatch.pl[1]

[1]: https://review.coreboot.org/plugins/gitiles/coreboot/+/refs/heads/master/util/lint/checkpatch.pl

Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Change-Id: I7957c9694300fefb85d11f7819c43af95271f14c

show more ...

fix(rss): fix msg deserialization bugs in comms

-fix1: size of struct instead of pointer during reply_size check
-fix2: update the out_vec length with the actual length from reply
message (e.

fix(rss): fix msg deserialization bugs in comms

-fix1: size of struct instead of pointer during reply_size check
-fix2: update the out_vec length with the actual length from reply
message (e.g. in case of an output buffer, the returned output
data length remained the size of the buffer and was not updated
with the size of the actual data in it)

Change-Id: Ibed5520ca1fb05df358de4bdf85ace219183866c
Signed-off-by: David Vincze <david.vincze@arm.com>

show more ...