Merge changes from topic "refactor_eip76_driver" into integration

* changes:
feat(marvell): add trng driver
revert(rambus-trng): remove ip-76 driver

revert(rambus-trng): remove ip-76 driver

The Rambus TRNG IP-76 driver was ported from Linux kernel (omap-rng.c),
which was initially licensed under GPL-2.0. In term of the license
violation, remove

revert(rambus-trng): remove ip-76 driver

The Rambus TRNG IP-76 driver was ported from Linux kernel (omap-rng.c),
which was initially licensed under GPL-2.0. In term of the license
violation, remove this driver and the related SMC call that originally
added by the following two commits:

commit 57660d9d7945 ("plat/marvell/armada/a8k: support HW RNG by SMC")
commit 6aa9f5d164e8 ("drivers/rambus: add TRNG-IP-76 driver")

Change-Id: Id8c99db2e51b49623b3b034106c989a46f690b60
Signed-off-by: Wilson Ding <dingwei@marvell.com>

show more ...

Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is pr

Merge changes I8f3afbe3,I441e7c69,I2e9465f7,Ib8756cd3,Iebe6ea7c, ... into integration

* changes:
plat/marvell: remove subversion from Marvell make files
drivers/marvell: check if TRNG unit is present
plat/marvell: a8k: move efuse definitions to separate header
plat/marvell/armada: fix TRNG return SMC handling
drivers: marvell: comphy: add rx training on 10G port
plat/marvell/armada: postpone MSS CPU startup to BL31 stage
plat: marvell: armada: a8k: Fix LD selector mask
plat/marvell/armada: allow builds without MSS support
drivers: marvell: misc-dfx: extend dfx whitelist
drivers: marvell: add support for secure read/write of dfx register-set
ddr_phy: use smc calls to access ddr phy registers
drivers: marvell: thermal: use dedicated function for thermal SiPs
drivers: marvell: add thermal sensor driver and expose it via SIP service
fix: plat: marvell: fix MSS loader for A8K family

show more ...

drivers/marvell: check if TRNG unit is present

Some Marvell SoCs may have crypto engine disabled in the HW.
This patch checks the AP LD0 efuse for crypto engine/TRNG
presence before initializing the

drivers/marvell: check if TRNG unit is present

Some Marvell SoCs may have crypto engine disabled in the HW.
This patch checks the AP LD0 efuse for crypto engine/TRNG
presence before initializing the driver.

Change-Id: I441e7c69a137106bd36302b028b04c0b31896dbd
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/47314
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>

show more ...

Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mappin

Merge changes I23f600b5,Icf9ffdf2,Iee7a51d1,I99afc312,I4bf8e8c0, ... into integration

* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver

show more ...

drivers/marvell/mochi: add support for cn913x in PCIe EP mode

Change-Id: I4dc33d1eb59395605f64e5aad5cafa10c53265cc
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1g

drivers/marvell/mochi: add support for cn913x in PCIe EP mode

Change-Id: I4dc33d1eb59395605f64e5aad5cafa10c53265cc
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/20453
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>

show more ...

drivers/marvell/mochi: add missing stream IDs configurations

- Add setup of DMA stream IDs in AP807/AP806 drivers

Change-Id: I23ffe86002db4753f812c63c31431a3d04056d07
Signed-off-by: Konstantin Poro

drivers/marvell/mochi: add missing stream IDs configurations

- Add setup of DMA stream IDs in AP807/AP806 drivers

Change-Id: I23ffe86002db4753f812c63c31431a3d04056d07
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>

show more ...

plat/marvell/armada/a8k: support HW RNG by SMC

Add initialization for TRNG-IP-76 driver and support SMC call
0xC200FF11 used for reading HW RNG value by secondary bootloader
software for KASLR suppo

plat/marvell/armada/a8k: support HW RNG by SMC

Add initialization for TRNG-IP-76 driver and support SMC call
0xC200FF11 used for reading HW RNG value by secondary bootloader
software for KASLR support.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I1d644f67457b28d347523f8a7bfc4eacc45cba68
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/32688
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>

show more ...

Merge "marvell: drivers: mochi: specify stream ID for SD/MMC" into integration

marvell: drivers: mochi: specify stream ID for SD/MMC

This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure prope

marvell: drivers: mochi: specify stream ID for SD/MMC

This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure properly the
IOMMU in OS and use the SD/MMC interface in a guest
Virtual Machine.

Change-Id: I99cbd2c9882eb558ba01405d3d8a3e969f06e082
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>

show more ...

Merge changes Ib68092d1,I816ea14e into integration

* changes:
plat: marvell: armada: scp_bl2: allow loading up to 8 images
plat: marvell: armada: add support for loading MG CM3 images

plat: marvell: armada: add support for loading MG CM3 images

In order to access MG SRAM, the amb bridge needs to be configured which is
done in bl2 platform init.

For MG CM3, the image is only load

plat: marvell: armada: add support for loading MG CM3 images

In order to access MG SRAM, the amb bridge needs to be configured which is
done in bl2 platform init.

For MG CM3, the image is only loaded to its SRAM and the CM3 itself is
left in reset. It is because the next stage bootloader (e.g. u-boot)
will trigger action which will take it out of reset when needed. This
can happen e.g. when appropriate device-tree setup (which has enabled
802.3 auto-neg) will be chosen. In other cases the MG CM3 should not be
running.

Change-Id: I816ea14e3a7174eace068ec44e3cc09998d0337e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

show more ...

Merge changes from topic "jc/shift-overflow" into integration

* changes:
Enable -Wshift-overflow=2 to check for undefined shift behavior
Update base code to not rely on undefined overflow behavi

Merge changes from topic "jc/shift-overflow" into integration

* changes:
Enable -Wshift-overflow=2 to check for undefined shift behavior
Update base code to not rely on undefined overflow behaviour
Update hisilicon drivers to not rely on undefined overflow behaviour
Update synopsys drivers to not rely on undefined overflow behaviour
Update imx platform to not rely on undefined overflow behaviour
Update mediatek platform to not rely on undefined overflow behaviour
Update layerscape platform to not rely on undefined overflow behaviour
Update intel platform to not rely on undefined overflow behaviour
Update rockchip platform to not rely on undefined overflow behaviour
Update renesas platform to not rely on undefined overflow behaviour
Update meson platform to not rely on undefined overflow behaviour
Update marvell platform to not rely on undefined overflow behaviour

show more ...

Update marvell platform to not rely on undefined overflow behaviour

This consists of ensuring that the left operand of each shift is
unsigned when the operation might overflow into the sign bit.

Ch

Update marvell platform to not rely on undefined overflow behaviour

This consists of ensuring that the left operand of each shift is
unsigned when the operation might overflow into the sign bit.

Change-Id: I78f386f5ac171d6e52383a3e42003e6fb3e96b57
Signed-off-by: Justin Chadwell <justin.chadwell@arm.com>

show more ...

Merge pull request #1726 from antonio-nino-diaz-arm/an/includes

Sanitise includes across codebase

Sanitise includes across codebase

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- inclu

Sanitise includes across codebase

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928d5b7 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a282 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca33988b9 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

show more ...

Merge pull request #1540 from MISL-EBU-System-SW/marvell-updates-18.09

Marvell updates 18.09

marvell: drivers: correct RTC init sequence

It turned out that resetting the RTC time register is not
necessary during initial configuration. Safely remove it
from the sequence.

Change-Id: Id2b9c7d

marvell: drivers: correct RTC init sequence

It turned out that resetting the RTC time register is not
necessary during initial configuration. Safely remove it
from the sequence.

Change-Id: Id2b9c7db44a8c8dbe88a7f8a21695b72a7fd78ee
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>

show more ...

Merge pull request #1450 from MISL-EBU-System-SW/marvell-support-v6

Marvell support for Armada 8K SoC family

marvell: drivers: Add MoChi drivers

Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 a

marvell: drivers: Add MoChi drivers

Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 and CP110

Change-Id: I9559343788fa2e5eb47e6384a4a7d47408787c02
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

show more ...