1 /* 2 * Bluewater Systems Snapper 9260 and 9G20 modules 3 * 4 * (C) Copyright 2011 Bluewater Systems 5 * Author: Andre Renaud <andre@bluewatersys.com> 6 * Author: Ryan Mallon <ryan@bluewatersys.com> 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 /* SoC type is defined in boards.cfg */ 15 #include <asm/hardware.h> 16 #include <linux/sizes.h> 17 18 #define CONFIG_SYS_TEXT_BASE 0x21f00000 19 20 /* ARM asynchronous clock */ 21 #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* External Crystal, in Hz */ 22 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 23 24 /* CPU */ 25 #define CONFIG_ARCH_CPU_INIT 26 27 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 28 #define CONFIG_SETUP_MEMORY_TAGS 29 #define CONFIG_INITRD_TAG 30 #define CONFIG_SKIP_LOWLEVEL_INIT 31 32 /* SDRAM */ 33 #define CONFIG_NR_DRAM_BANKS 1 34 #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 35 #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) /* 64MB */ 36 #define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM1 + 0x1000 - \ 37 GENERATED_GBL_DATA_SIZE) 38 39 /* Mem test settings */ 40 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 41 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024)) 42 43 /* NAND Flash */ 44 #define CONFIG_SYS_MAX_NAND_DEVICE 1 45 #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 46 #define CONFIG_SYS_NAND_DBW_8 47 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */ 48 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */ 49 #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 50 #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 51 52 /* Ethernet */ 53 #define CONFIG_MACB 54 #define CONFIG_RMII 55 #define CONFIG_NET_RETRY_COUNT 20 56 #define CONFIG_RESET_PHY_R 57 #define CONFIG_AT91_WANTS_COMMON_PHY 58 #define CONFIG_TFTP_PORT 59 #define CONFIG_TFTP_TSIZE 60 61 /* USB */ 62 #define CONFIG_USB_ATMEL 63 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 64 #define CONFIG_USB_OHCI_NEW 65 #define CONFIG_SYS_USB_OHCI_CPU_INIT 66 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_UHP_BASE 67 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" 68 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 69 70 /* GPIOs and IO expander */ 71 #define CONFIG_ATMEL_LEGACY 72 #define CONFIG_AT91_GPIO 73 #define CONFIG_AT91_GPIO_PULLUP 1 74 #define CONFIG_PCA953X 75 #define CONFIG_SYS_I2C_PCA953X_ADDR 0x28 76 #define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x28, 16} } 77 78 /* UARTs/Serial console */ 79 #define CONFIG_ATMEL_USART 80 #ifndef CONFIG_DM_SERIAL 81 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 82 #define CONFIG_USART_ID ATMEL_ID_SYS 83 #endif 84 85 /* I2C - Bit-bashed */ 86 #define CONFIG_SYS_I2C 87 #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ 88 #define CONFIG_SYS_I2C_SOFT_SPEED 100000 89 #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F 90 #define CONFIG_SOFT_I2C_READ_REPEATED_START 91 #define I2C_INIT do { \ 92 at91_set_gpio_output(AT91_PIN_PA23, 1); \ 93 at91_set_gpio_output(AT91_PIN_PA24, 1); \ 94 at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \ 95 at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \ 96 } while (0) 97 #define I2C_SOFT_DECLARATIONS 98 #define I2C_ACTIVE 99 #define I2C_TRISTATE at91_set_gpio_input(AT91_PIN_PA23, 1); 100 #define I2C_READ at91_get_gpio_value(AT91_PIN_PA23); 101 #define I2C_SDA(bit) do { \ 102 if (bit) { \ 103 at91_set_gpio_input(AT91_PIN_PA23, 1); \ 104 } else { \ 105 at91_set_gpio_output(AT91_PIN_PA23, 1); \ 106 at91_set_gpio_value(AT91_PIN_PA23, bit); \ 107 } \ 108 } while (0) 109 #define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit) 110 #define I2C_DELAY udelay(2) 111 112 /* Boot options */ 113 #define CONFIG_SYS_LOAD_ADDR 0x23000000 114 115 #define CONFIG_BOOTP_BOOTFILESIZE 116 #define CONFIG_BOOTP_BOOTPATH 117 #define CONFIG_BOOTP_GATEWAY 118 #define CONFIG_BOOTP_HOSTNAME 119 120 /* Environment settings */ 121 #define CONFIG_ENV_OFFSET (512 << 10) 122 #define CONFIG_ENV_SIZE (256 << 10) 123 #define CONFIG_ENV_OVERWRITE 124 125 /* Console settings */ 126 #define CONFIG_SYS_LONGHELP 127 #define CONFIG_CMDLINE_EDITING 128 #define CONFIG_AUTO_COMPLETE 129 130 /* U-Boot memory settings */ 131 #define CONFIG_SYS_MALLOC_LEN (1 << 20) 132 133 #endif /* __CONFIG_H */ 134