1 /* 2 * Copyright (C) 2011 Ilya Yanok, Emcraft Systems 3 * 4 * Based on omap3_evm_config.h 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 /* 13 * High Level Configuration Options 14 */ 15 16 #define CONFIG_MACH_TYPE MACH_TYPE_MCX 17 18 #define CONFIG_EMIF4 /* The chip has EMIF4 controller */ 19 20 #include <asm/arch/cpu.h> /* get chip and board defs */ 21 #include <asm/arch/omap.h> 22 23 /* 24 * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader 25 * and older u-boot.bin with the new U-Boot SPL. 26 */ 27 #define CONFIG_SYS_TEXT_BASE 0x80008000 28 29 /* Clock Defines */ 30 #define V_OSCK 26000000 /* Clock output from T2 */ 31 #define V_SCLK (V_OSCK >> 1) 32 33 #define CONFIG_MISC_INIT_R 34 35 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ 36 #define CONFIG_SETUP_MEMORY_TAGS 37 #define CONFIG_INITRD_TAG 38 #define CONFIG_REVISION_TAG 39 40 /* 41 * Size of malloc() pool 42 */ 43 #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ 44 #define CONFIG_SYS_MALLOC_LEN (1024 << 10) 45 /* 46 * DDR related 47 */ 48 #define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024) 49 50 /* 51 * Hardware drivers 52 */ 53 54 /* 55 * NS16550 Configuration 56 */ 57 #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ 58 59 #define CONFIG_SYS_NS16550_SERIAL 60 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 61 #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK 62 63 /* 64 * select serial console configuration 65 */ 66 #define CONFIG_CONS_INDEX 3 67 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 68 #define CONFIG_SERIAL3 3 /* UART3 */ 69 70 /* allow to overwrite serial and ethaddr */ 71 #define CONFIG_ENV_OVERWRITE 72 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 73 115200} 74 75 /* EHCI */ 76 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57 77 78 /* commands to include */ 79 80 #define CONFIG_SYS_I2C 81 #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 82 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 83 84 /* RTC */ 85 #define CONFIG_RTC_DS1337 86 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 87 88 /* 89 * Board NAND Info. 90 */ 91 #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ 92 /* to access nand */ 93 #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ 94 /* to access */ 95 /* nand at CS0 */ 96 97 #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */ 98 /* NAND devices */ 99 #define CONFIG_JFFS2_NAND 100 /* nand device jffs2 lives on */ 101 #define CONFIG_JFFS2_DEV "nand0" 102 /* start of jffs2 partition */ 103 #define CONFIG_JFFS2_PART_OFFSET 0x680000 104 #define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */ 105 106 /* Environment information */ 107 108 #define CONFIG_BOOTFILE "uImage" 109 110 /* Setup MTD for NAND on the SOM */ 111 #define MTDIDS_DEFAULT "nand0=omap2-nand.0" 112 #define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO)," \ 113 "1m(u-boot),256k(env1)," \ 114 "256k(env2),6m(kernel),6m(k_recovery)," \ 115 "8m(fs_recovery),-(common_data)" 116 117 #define CONFIG_HOSTNAME mcx 118 #define CONFIG_EXTRA_ENV_SETTINGS \ 119 "adddbg=setenv bootargs ${bootargs} trace_buf_size=64M\0" \ 120 "adddebug=setenv bootargs ${bootargs} earlyprintk=serial\0" \ 121 "addeth=setenv bootargs ${bootargs} ethaddr=${ethaddr}\0" \ 122 "addfb=setenv bootargs ${bootargs} vram=6M " \ 123 "omapfb.vram=1:2M,2:2M,3:2M omapdss.def_disp=lcd\0" \ 124 "addip_sta=setenv bootargs ${bootargs} " \ 125 "ip=${ipaddr}:${serverip}:${gatewayip}:" \ 126 "${netmask}:${hostname}:eth0:off\0" \ 127 "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \ 128 "addip=if test -n ${ipdyn};then run addip_dyn;" \ 129 "else run addip_sta;fi\0" \ 130 "addmisc=setenv bootargs ${bootargs} ${misc}\0" \ 131 "addtty=setenv bootargs ${bootargs} " \ 132 "console=${consoledev},${baudrate}\0" \ 133 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 134 "baudrate=115200\0" \ 135 "consoledev=ttyO2\0" \ 136 "hostname=" __stringify(CONFIG_HOSTNAME) "\0" \ 137 "loadaddr=0x82000000\0" \ 138 "load=tftp ${loadaddr} ${u-boot}\0" \ 139 "load_k=tftp ${loadaddr} ${bootfile}\0" \ 140 "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \ 141 "loadmlo=tftp ${loadaddr} ${mlo}\0" \ 142 "mlo=" __stringify(CONFIG_HOSTNAME) "/MLO\0" \ 143 "mmcargs=root=/dev/mmcblk0p2 rw " \ 144 "rootfstype=ext3 rootwait\0" \ 145 "mmcboot=echo Booting from mmc ...; " \ 146 "run mmcargs; " \ 147 "run addip addtty addmtd addfb addeth addmisc;" \ 148 "run loaduimage; " \ 149 "bootm ${loadaddr}\0" \ 150 "net_nfs=run load_k; " \ 151 "run nfsargs; " \ 152 "run addip addtty addmtd addfb addeth addmisc;" \ 153 "bootm ${loadaddr}\0" \ 154 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 155 "nfsroot=${serverip}:${rootpath}\0" \ 156 "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.img\0" \ 157 "uboot_addr=0x80000\0" \ 158 "update=nandecc sw;nand erase ${uboot_addr} 100000;" \ 159 "nand write ${loadaddr} ${uboot_addr} 80000\0" \ 160 "updatemlo=nandecc hw;nand erase 0 20000;" \ 161 "nand write ${loadaddr} 0 20000\0" \ 162 "upd=if run load;then echo Updating u-boot;if run update;" \ 163 "then echo U-Boot updated;" \ 164 "else echo Error updating u-boot !;" \ 165 "echo Board without bootloader !!;" \ 166 "fi;" \ 167 "else echo U-Boot not downloaded..exiting;fi\0" \ 168 "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \ 169 "bootscript=echo Running bootscript from mmc ...; " \ 170 "source ${loadaddr}\0" \ 171 "nandargs=setenv bootargs ubi.mtd=7 " \ 172 "root=ubi0:rootfs rootfstype=ubifs\0" \ 173 "nandboot=echo Booting from nand ...; " \ 174 "run nandargs; " \ 175 "ubi part nand0,4;" \ 176 "ubi readvol ${loadaddr} kernel;" \ 177 "run addtty addmtd addfb addeth addmisc;" \ 178 "bootm ${loadaddr}\0" \ 179 "preboot=ubi part nand0,7;" \ 180 "ubi readvol ${loadaddr} splash;" \ 181 "bmp display ${loadaddr};" \ 182 "gpio set 55\0" \ 183 "swupdate_args=setenv bootargs root=/dev/ram " \ 184 "quiet loglevel=1 " \ 185 "consoleblank=0 ${swupdate_misc}\0" \ 186 "swupdate=echo Running Sw-Update...;" \ 187 "if printenv mtdparts;then echo Starting SwUpdate...; " \ 188 "else mtdparts default;fi; " \ 189 "ubi part nand0,5;" \ 190 "ubi readvol 0x82000000 kernel_recovery;" \ 191 "ubi part nand0,6;" \ 192 "ubi readvol 0x84000000 fs_recovery;" \ 193 "run swupdate_args; " \ 194 "setenv bootargs ${bootargs} " \ 195 "${mtdparts} " \ 196 "vram=6M omapfb.vram=1:2M,2:2M,3:2M " \ 197 "omapdss.def_disp=lcd;" \ 198 "bootm 0x82000000 0x84000000\0" \ 199 "bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \ 200 "then source 82000000;else run nandboot;fi\0" 201 202 #define CONFIG_AUTO_COMPLETE 203 #define CONFIG_CMDLINE_EDITING 204 205 /* 206 * Miscellaneous configurable options 207 */ 208 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 209 #define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ 210 /* Boot Argument Buffer Size */ 211 #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) 212 /* memtest works on */ 213 #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) 214 #define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ 215 0x01F00000) /* 31MB */ 216 217 #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */ 218 /* address */ 219 #define CONFIG_PREBOOT 220 221 /* 222 * AM3517 has 12 GP timers, they can be driven by the system clock 223 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). 224 * This rate is divided by a local divisor. 225 */ 226 #define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 227 #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 228 229 /* 230 * Physical Memory Map 231 */ 232 #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ 233 #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 234 #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 235 236 /* 237 * FLASH and environment organization 238 */ 239 240 /* **** PISMO SUPPORT *** */ 241 242 /* Redundant Environment */ 243 #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ 244 #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET 245 #define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET 246 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 247 2 * CONFIG_SYS_ENV_SECT_SIZE) 248 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 249 250 /* Flash banks JFFS2 should use */ 251 #define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ 252 CONFIG_SYS_MAX_NAND_DEVICE) 253 #define CONFIG_SYS_JFFS2_MEM_NAND 254 /* use flash_info[2] */ 255 #define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS 256 #define CONFIG_SYS_JFFS2_NUM_BANKS 1 257 258 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 259 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 260 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 261 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ 262 CONFIG_SYS_INIT_RAM_SIZE - \ 263 GENERATED_GBL_DATA_SIZE) 264 265 /* Defines for SPL */ 266 #define CONFIG_SPL_FRAMEWORK 267 268 #define CONFIG_SPL_NAND_BASE 269 #define CONFIG_SPL_NAND_DRIVERS 270 #define CONFIG_SPL_NAND_ECC 271 272 #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ 273 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ 274 #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK 275 276 /* move malloc and bss high to prevent clashing with the main image */ 277 #define CONFIG_SYS_SPL_MALLOC_START 0x8f000000 278 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 279 #define CONFIG_SPL_BSS_START_ADDR 0x8f080000 /* end of RAM */ 280 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 281 282 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 283 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 284 285 /* NAND boot config */ 286 #define CONFIG_SYS_NAND_PAGE_COUNT 64 287 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 288 #define CONFIG_SYS_NAND_OOBSIZE 64 289 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) 290 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 291 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 292 #define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47,\ 293 48, 49, 50, 51, 52, 53, 54, 55,\ 294 56, 57, 58, 59, 60, 61, 62, 63} 295 #define CONFIG_SYS_NAND_ECCSIZE 256 296 #define CONFIG_SYS_NAND_ECCBYTES 3 297 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW 298 #define CONFIG_SPL_NAND_SOFTECC 299 300 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 301 302 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 303 304 /* 305 * ethernet support 306 * 307 */ 308 #if defined(CONFIG_CMD_NET) 309 #define CONFIG_DRIVER_TI_EMAC 310 #define CONFIG_DRIVER_TI_EMAC_USE_RMII 311 #define CONFIG_MII 312 #define CONFIG_BOOTP_DNS 313 #define CONFIG_BOOTP_DNS2 314 #define CONFIG_BOOTP_SEND_HOSTNAME 315 #define CONFIG_NET_RETRY_COUNT 10 316 #endif 317 318 #define CONFIG_SPLASH_SCREEN 319 #define CONFIG_VIDEO_BMP_RLE8 320 #define CONFIG_VIDEO_OMAP3 321 322 #endif /* __CONFIG_H */ 323