1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef REALTEK_POWER_SEQUENCE_8188F 3 #define REALTEK_POWER_SEQUENCE_8188F 4 5 #include "HalPwrSeqCmd.h" 6 7 /* 8 Check document WM-20130815-JackieLau-RTL8188F_Power_Architecture v08.vsd 9 There are 6 HW Power States: 10 0: POFF--Power Off 11 1: PDN--Power Down 12 2: CARDEMU--Card Emulation 13 3: ACT--Active Mode 14 4: LPS--Low Power State 15 5: SUS--Suspend 16 17 The transision from different states are defined below 18 TRANS_CARDEMU_TO_ACT 19 TRANS_ACT_TO_CARDEMU 20 TRANS_CARDEMU_TO_SUS 21 TRANS_SUS_TO_CARDEMU 22 TRANS_CARDEMU_TO_PDN 23 TRANS_ACT_TO_LPS 24 TRANS_LPS_TO_ACT 25 26 TRANS_END 27 */ 28 #define RTL8188F_TRANS_CARDEMU_TO_ACT_STEPS 13 29 #define RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS 15 30 #define RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS 14 31 #define RTL8188F_TRANS_SUS_TO_CARDEMU_STEPS 15 32 #define RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS 15 33 #define RTL8188F_TRANS_PDN_TO_CARDEMU_STEPS 15 34 #define RTL8188F_TRANS_ACT_TO_LPS_STEPS 11 35 #define RTL8188F_TRANS_LPS_TO_ACT_STEPS 13 36 #define RTL8188F_TRANS_ACT_TO_SWLPS_STEPS 21 37 #define RTL8188F_TRANS_SWLPS_TO_ACT_STEPS 14 38 #define RTL8188F_TRANS_END_STEPS 1 39 40 41 #define RTL8188F_TRANS_CARDEMU_TO_ACT \ 42 /* format */ \ 43 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 44 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/ \ 45 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \ 46 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/ \ 47 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT3), 0},/* 0x4[11]=1'b0 disable WL suspend*/ \ 48 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/* 0x4[8]=1 polling until return 0*/ \ 49 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT0, 0},/**/ \ 50 {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x35}, /*0x27<=35 to reduce RF noise*/ 51 52 #define RTL8188F_TRANS_ACT_TO_CARDEMU \ 53 /* format */ \ 54 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 55 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/ \ 56 {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\ 57 {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x34}, /*0x27 <= 34, xtal_qsel = 0 to xtal bring up*/\ 58 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ 59 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ 60 61 #define RTL8188F_TRANS_CARDEMU_TO_SUS \ 62 /* format */ \ 63 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 64 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, /*0x07 = 0x00 , SOP option to disable BG/MB*/ \ 65 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 66 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ 67 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ \ 68 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/ 69 70 #define RTL8188F_TRANS_SUS_TO_CARDEMU \ 71 /* format */ \ 72 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 73 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ 74 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ 75 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ \ 76 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/ 77 78 #define RTL8188F_TRANS_CARDEMU_TO_CARDDIS \ 79 /* format */ \ 80 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 81 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, /*0x07 = 0x00 , SOP option to disable BG/MB*/ \ 82 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 83 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/ \ 84 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/ \ 85 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, BIT4},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/ 86 87 #define RTL8188F_TRANS_CARDDIS_TO_CARDEMU \ 88 /* format */ \ 89 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 90 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \ 91 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\ 92 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT3 | BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ \ 93 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT4, 0},/* 0xC4[4] <= 1, turn off USB APHY LDO under suspend mode*/ 94 95 96 #define RTL8188F_TRANS_CARDEMU_TO_PDN \ 97 /* format */ \ 98 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 99 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\ 100 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/ 101 102 #define RTL8188F_TRANS_PDN_TO_CARDEMU \ 103 /* format */ \ 104 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 105 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/ 106 107 #define RTL8188F_TRANS_ACT_TO_LPS \ 108 /* format */ \ 109 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 110 {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*set RPWM IMR*/ \ 111 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \ 112 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 113 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 114 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 115 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ 116 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 117 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \ 118 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ 119 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ 120 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ 121 122 123 #define RTL8188F_TRANS_LPS_TO_ACT \ 124 /* format */ \ 125 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 126 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ 127 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ 128 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 129 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 130 {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x35},/*xtal_qsel = 1 for low noise*/ \ 131 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0 TSF in 40M*/\ 132 {0x002B, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x1c, 0x1c}, /*. 0x2b[4:2] = 3b'111 to enable BB, AFE clock*/\ 133 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/\ 134 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 135 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1 | BIT0, BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 136 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 137 138 139 #define RTL8188F_TRANS_ACT_TO_SWLPS \ 140 /* format */ \ 141 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 142 {0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*set RPWM IMR*/ \ 143 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \ 144 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 145 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 146 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 147 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled, and clock are gated*/ \ 148 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 149 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/ \ 150 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/ \ 151 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ 152 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/ \ 153 {0x002b, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0x1C, 0x00},/*0x2b[4:2]<=0 to gated BB, AFE clock*/ \ 154 {0x0027, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x34},/*xtal_qsel = 0 for bring up*/ \ 155 {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x00},/* sdio LPS option*/ \ 156 {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0x83},/* usb LPS option, open bandgap, xtal*/ \ 157 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT5, 0}, /* 0xC4[5]<=0, digital LDO no standby mode*/ \ 158 {0x00C4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, BIT7}, /* 0xC4[7]<=1, on domain voltage adjust*/ \ 159 {0x00a7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0xe0}, /* low power LPS enable for sdio*/ \ 160 {0x00a7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xff, 0xe4}, /* low power LPS enable for usb*/ \ 161 {0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /* enable WL_LPS_EN*/ 162 163 164 #define RTL8188F_TRANS_SWLPS_TO_ACT \ 165 /* format */ \ 166 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 167 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\ 168 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1, enable security engine*/\ 169 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 170 {0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x09}, /*. reset MAC rx state machine*/\ 171 {0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x86}, /*. reset MAC rx state machine*/\ 172 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/ \ 173 {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/ \ 174 {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/ \ 175 {0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/ \ 176 {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/ \ 177 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */ \ 178 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */ \ 179 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT0, BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 180 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 181 182 #define RTL8188F_TRANS_END \ 183 /* format */ \ 184 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 185 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0}, 186 187 188 extern WLAN_PWR_CFG rtl8188F_power_on_flow[RTL8188F_TRANS_CARDEMU_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS]; 189 extern WLAN_PWR_CFG rtl8188F_radio_off_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_END_STEPS]; 190 extern WLAN_PWR_CFG rtl8188F_card_disable_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS]; 191 extern WLAN_PWR_CFG rtl8188F_card_enable_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS]; 192 extern WLAN_PWR_CFG rtl8188F_suspend_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188F_TRANS_END_STEPS]; 193 extern WLAN_PWR_CFG rtl8188F_resume_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_SUS_STEPS + RTL8188F_TRANS_END_STEPS]; 194 extern WLAN_PWR_CFG rtl8188F_hwpdn_flow[RTL8188F_TRANS_ACT_TO_CARDEMU_STEPS + RTL8188F_TRANS_CARDEMU_TO_PDN_STEPS + RTL8188F_TRANS_END_STEPS]; 195 extern WLAN_PWR_CFG rtl8188F_enter_lps_flow[RTL8188F_TRANS_ACT_TO_LPS_STEPS + RTL8188F_TRANS_END_STEPS]; 196 extern WLAN_PWR_CFG rtl8188F_leave_lps_flow[RTL8188F_TRANS_LPS_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS]; 197 extern WLAN_PWR_CFG rtl8188F_enter_swlps_flow[RTL8188F_TRANS_ACT_TO_SWLPS_STEPS + RTL8188F_TRANS_END_STEPS]; 198 extern WLAN_PWR_CFG rtl8188F_leave_swlps_flow[RTL8188F_TRANS_SWLPS_TO_ACT_STEPS + RTL8188F_TRANS_END_STEPS]; 199 #endif 200