xref: /OK3568_Linux_fs/kernel/drivers/net/wireless/rockchip_wlan/rtl8821cs/include/Hal8192FPwrSeq.h (revision 4882a59341e53eb6f0b4789bf948001014eff981) 
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /******************************************************************************
3  *
4  * Copyright(c) 2016 - 2017 Realtek Corporation.
5  *
6  * This program is free software; you can redistribute it and/or modify it
7  * under the terms of version 2 of the GNU General Public License as
8  * published by the Free Software Foundation.
9  *
10  * This program is distributed in the hope that it will be useful, but WITHOUT
11  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12  * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
13  * more details.
14  *
15  *****************************************************************************/
16 #ifndef REALTEK_POWER_SEQUENCE_8192F
17 #define REALTEK_POWER_SEQUENCE_8192F
18 #define POWER_SEQUENCE_8192F_VER 04
19 /* #include "PwrSeqCmd.h" */
20 #include "HalPwrSeqCmd.h"
21 
22 /*
23 	Check document WM-20110607-Paul-RTL8192e_Power_Architecture-R02.vsd
24 	There are 6 HW Power States:
25 	0: POFF--Power Off
26 	1: PDN--Power Down
27 	2: CARDEMU--Card Emulation
28 	3: ACT--Active Mode
29 	4: LPS--Low Power State
30 	5: SUS--Suspend
31 
32 	The transition from different states are defined below
33 	TRANS_CARDEMU_TO_ACT
34 	TRANS_ACT_TO_CARDEMU
35 	TRANS_CARDEMU_TO_SUS
36 	TRANS_SUS_TO_CARDEMU
37 	TRANS_CARDEMU_TO_PDN
38 	TRANS_ACT_TO_LPS
39 	TRANS_LPS_TO_ACT
40 
41 	TRANS_END
42 */
43 #define	RTL8192F_TRANS_CARDEMU_TO_ACT_STEPS	38
44 #define	RTL8192F_TRANS_ACT_TO_CARDEMU_STEPS	8
45 #define	RTL8192F_TRANS_CARDEMU_TO_SUS_STEPS	7
46 #define	RTL8192F_TRANS_SUS_TO_CARDEMU_STEPS	5
47 #define	RTL8192F_TRANS_CARDEMU_TO_CARDDIS_STEPS	8
48 #define	RTL8192F_TRANS_CARDDIS_TO_CARDEMU_STEPS	8
49 #define	RTL8192F_TRANS_CARDEMU_TO_PDN_STEPS	4
50 #define	RTL8192F_TRANS_PDN_TO_CARDEMU_STEPS	1
51 #define	RTL8192F_TRANS_ACT_TO_LPS_STEPS		13
52 #define	RTL8192F_TRANS_LPS_TO_ACT_STEPS		11
53 #define	RTL8192F_TRANS_END_STEPS	1
54 
55 
56 #define RTL8192F_TRANS_CARDEMU_TO_ACT 														\
57 	/* format */																\
58 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
59 	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/	\
60 	{0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/	\
61 	{0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \
62 	{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/	\
63 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3|BIT2), 0},/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \
64 	{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0 , BIT0},/* Disable USB suspend */	\
65 	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/	\
66 	{0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0 , 0},/* Enable USB suspend */	\
67 	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/ \
68 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, (BIT1|BIT0), 0}, \
69 	{0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2},/* SWR OCP enable 0x10[18]=1*/ \
70 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/	\
71 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/ \
72 	{0x007f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x7c[31]=1,LDO has max output capability*/ \
73 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \
74 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/ \
75 	{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* Enable WL control XTAL setting*/ \
76 	{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\
77 	{0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 data mode*/\
78 	{0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\
79 	{0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\
80 	{0x0068, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0},/*RF HW ON/OFF Enable*/\
81 	{0x001C, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/*Register Lock Disable*/\
82 	{0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/*For GPIO9 internal pull high setting*/\
83 	{0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S1*/\
84 	{0x007B, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S0*/\
85 	{0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x07},/*enable RF path S1*/\
86 	{0x007B, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x07},/*enalbe RF path S0*/\
87 	{0x0097, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*AFE_Ctrl*/\
88 	{0x00DC, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xCC},/*AFE_Ctrl*/\
89 	{0x0024, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x18, 0x00},/*AFE_Ctrl 0x24[4:3]=00 for xtal gmn*/\
90 	{0x1050, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*GPIO_A[7:0] Pull down software register*/\
91 	{0x1051, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*GPIO_A[15:8] Pull down software register*/\
92 	{0x1052, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*GPIO_A[23:16] Pull down software register*/\
93 	{0x1053, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*GPIO_A[31:24] Pull down software register*/\
94 	{0x105B, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*GPIO_B[7:0] Pull down software register*/\
95 	{0x001C, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*Register Lock Enable*/\
96 	{0x0077, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT7|BIT6), 0x3},/*set HCI Power sequence state delay time:0*/
97 
98 
99 #define RTL8192F_TRANS_ACT_TO_CARDEMU													\
100 	/* format */																\
101 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
102 	/*{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, */ /*0x1F[7:0] = 0 turn off RF*/	\
103 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x2[0]=0 Reset BB,RF enter Power Down mode*/ \
104 	{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \
105 	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/ \
106 	{0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, 0}, /*0x10[18] = 0 to disable ocp*/	\
107 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/	\
108 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
109 	{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/   \
110 	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\
111 
112 
113 #define RTL8192F_TRANS_CARDEMU_TO_SUS													\
114 	/* format */																\
115 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
116 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \
117 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
118 	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/	\
119 	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 USB|SDIO SOP option to disable BG/MB/ACK/SWR*/   \
120 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/	\
121 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
122 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
123 
124 #define RTL8192F_TRANS_SUS_TO_CARDEMU													\
125 	/* format */																\
126 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
127 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
128 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
129 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
130 	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
131 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
132 
133 
134 #define RTL8192F_TRANS_CARDEMU_TO_CARDDIS													\
135 	/* format */																\
136 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/	\
137 	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/	\
138 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
139 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/	\
140 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend*/	\
141 	{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/   \
142 	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/	\
143 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
144 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/
145 
146 #define RTL8192F_TRANS_CARDDIS_TO_CARDEMU													\
147 	/* format */																\
148 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
149 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/ \
150 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/ \
151 	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
152 	{0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/	\
153 	{0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT2, BIT2}, /*0x10[18] = 1 to enable ocp*/	\
154 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
155 	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
156 	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/
157 
158 
159 #define RTL8192F_TRANS_CARDEMU_TO_PDN												\
160 	/* format */																\
161 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
162 	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/	\
163 	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \
164 	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
165 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/
166 
167 #define RTL8192F_TRANS_PDN_TO_CARDEMU												\
168 	/* format */																\
169 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
170 	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/
171 
172 #define RTL8192F_TRANS_ACT_TO_LPS														\
173 	/* format */																\
174 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
175 	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/	\
176 	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/	\
177 	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
178 	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
179 	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
180 	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
181 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
182 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\
183 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/	\
184 	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/	\
185 	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \
186 	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/	\
187 	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/	\
188 
189 
190 #define RTL8192F_TRANS_LPS_TO_ACT															\
191 	/* format */																\
192 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
193 	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
194 	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
195 	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
196 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
197 	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.	0x08[4] = 0 	 switch TSF to 40M*/\
198 	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\
199 	{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.	0x29[7:6] = 2b'00	 enable BB clock*/\
200 	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1*/\
201 	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
202 	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
203 	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/
204 
205 #define RTL8192F_TRANS_END															\
206 	/* format */																\
207 	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
208 	{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //
209 
210 
211 extern WLAN_PWR_CFG rtl8192F_power_on_flow[RTL8192F_TRANS_CARDEMU_TO_ACT_STEPS+RTL8192F_TRANS_END_STEPS];
212 extern WLAN_PWR_CFG rtl8192F_radio_off_flow[RTL8192F_TRANS_ACT_TO_CARDEMU_STEPS+RTL8192F_TRANS_END_STEPS];
213 extern WLAN_PWR_CFG rtl8192F_card_disable_flow[RTL8192F_TRANS_ACT_TO_CARDEMU_STEPS+RTL8192F_TRANS_CARDEMU_TO_CARDDIS_STEPS+RTL8192F_TRANS_END_STEPS];
214 extern WLAN_PWR_CFG rtl8192F_card_enable_flow[RTL8192F_TRANS_CARDDIS_TO_CARDEMU_STEPS+RTL8192F_TRANS_CARDEMU_TO_ACT_STEPS+RTL8192F_TRANS_END_STEPS];
215 extern WLAN_PWR_CFG rtl8192F_suspend_flow[RTL8192F_TRANS_ACT_TO_CARDEMU_STEPS+RTL8192F_TRANS_CARDEMU_TO_SUS_STEPS+RTL8192F_TRANS_END_STEPS];
216 extern WLAN_PWR_CFG rtl8192F_resume_flow[RTL8192F_TRANS_SUS_TO_CARDEMU_STEPS+RTL8192F_TRANS_CARDEMU_TO_ACT_STEPS+RTL8192F_TRANS_END_STEPS];
217 extern WLAN_PWR_CFG rtl8192F_hwpdn_flow[RTL8192F_TRANS_ACT_TO_CARDEMU_STEPS+RTL8192F_TRANS_CARDEMU_TO_PDN_STEPS+RTL8192F_TRANS_END_STEPS];
218 extern WLAN_PWR_CFG rtl8192F_enter_lps_flow[RTL8192F_TRANS_ACT_TO_LPS_STEPS+RTL8192F_TRANS_END_STEPS];
219 extern WLAN_PWR_CFG rtl8192F_leave_lps_flow[RTL8192F_TRANS_LPS_TO_ACT_STEPS+RTL8192F_TRANS_END_STEPS];
220 
221 #endif
222