1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /****************************************************************************** 3 * 4 * Copyright(c) 2016 - 2017 Realtek Corporation. 5 * 6 * This program is free software; you can redistribute it and/or modify it 7 * under the terms of version 2 of the GNU General Public License as 8 * published by the Free Software Foundation. 9 * 10 * This program is distributed in the hope that it will be useful, but WITHOUT 11 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 12 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 13 * more details. 14 * 15 *****************************************************************************/ 16 #ifndef REALTEK_POWER_SEQUENCE_8723D 17 #define REALTEK_POWER_SEQUENCE_8723D 18 19 /* #include "PwrSeqCmd.h" */ 20 #include "HalPwrSeqCmd.h" 21 22 /* 23 Check document WM-20110607-Paul-RTL8192e_Power_Architecture-R02.vsd 24 There are 6 HW Power States: 25 0: POFF--Power Off 26 1: PDN--Power Down 27 2: CARDEMU--Card Emulation 28 3: ACT--Active Mode 29 4: LPS--Low Power State 30 5: SUS--Suspend 31 32 The transition from different states are defined below 33 TRANS_CARDEMU_TO_ACT 34 TRANS_ACT_TO_CARDEMU 35 TRANS_CARDEMU_TO_SUS 36 TRANS_SUS_TO_CARDEMU 37 TRANS_CARDEMU_TO_PDN 38 TRANS_ACT_TO_LPS 39 TRANS_LPS_TO_ACT 40 41 TRANS_END 42 */ 43 #define RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS 27 44 #define RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS 8 45 #define RTL8723D_TRANS_CARDEMU_TO_SUS_STEPS 7 46 #define RTL8723D_TRANS_SUS_TO_CARDEMU_STEPS 5 47 #define RTL8723D_TRANS_CARDEMU_TO_CARDDIS_STEPS 8 48 #define RTL8723D_TRANS_CARDDIS_TO_CARDEMU_STEPS 7 49 #define RTL8723D_TRANS_CARDEMU_TO_PDN_STEPS 4 50 #define RTL8723D_TRANS_PDN_TO_CARDEMU_STEPS 1 51 #define RTL8723D_TRANS_ACT_TO_LPS_STEPS 13 52 #define RTL8723D_TRANS_LPS_TO_ACT_STEPS 11 53 #define RTL8723D_TRANS_END_STEPS 1 54 55 56 #define RTL8723D_TRANS_CARDEMU_TO_ACT \ 57 /* format */ \ 58 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 59 {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \ 60 {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/ \ 61 {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \ 62 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4) | BIT(3) | BIT2), 0},/* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \ 63 {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , BIT(0)},/* Disable USB suspend */ \ 64 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1 power ready*/ \ 65 {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , 0},/* Enable USB suspend */ \ 66 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]=1*/ \ 67 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, (BIT(1) | BIT(0)), 0}, \ 68 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* disable HWPDN 0x04[15]=0*/ \ 69 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4) | BIT(3)), 0},/* disable WL suspend*/ \ 70 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* polling until return 0*/ \ 71 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0},/**/ \ 72 {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)},/* Enable WL control XTAL setting*/ \ 73 {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable falling edge triggering interrupt*/\ 74 {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable GPIO9 interrupt mode*/\ 75 {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Enable GPIO9 input mode*/\ 76 {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/*Enable HSISR GPIO[C:0] interrupt*/\ 77 {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)},/*Enable HSISR GPIO9 interrupt*/\ 78 {0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3), BIT(3)},/*For GPIO9 internal pull high setting by test chip*/\ 79 {0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)},/*For GPIO9 internal pull high setting*/\ 80 {0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S1*/\ 81 {0x0077, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*reset RF path S0*/\ 82 {0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/*enable RF path S1*/\ 83 {0x0077, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x07},/*enalbe RF path S0*/\ 84 85 86 #define RTL8723D_TRANS_ACT_TO_CARDEMU \ 87 /* format */ \ 88 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 89 /*{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, */ /*0x1F[7:0] = 0 turn off RF*/ \ 90 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x2[0]=0 Reset BB, RF enter Power Down mode*/ \ 91 {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Enable rising edge triggering interrupt*/ \ 92 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset 0x04[16]=1*/ \ 93 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ 94 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ 95 {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), 0},/* Enable BT control XTAL setting*/\ 96 {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \ 97 {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/\ 98 99 100 #define RTL8723D_TRANS_CARDEMU_TO_SUS \ 101 /* format */ \ 102 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 103 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT4 | BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 104 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 105 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ 106 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \ 107 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3 | BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ 108 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \ 109 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/ 110 111 #define RTL8723D_TRANS_SUS_TO_CARDEMU \ 112 /* format */ \ 113 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 114 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \ 115 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \ 116 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\ 117 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ 118 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/ 119 120 121 #define RTL8723D_TRANS_CARDEMU_TO_CARDDIS \ 122 /* format */ \ 123 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 124 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07 = 0x20 , SOP option to disable BG/MB*/ \ 125 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \ 126 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), BIT(2)}, /*0x04[10] = 1, enable SW LPS*/ \ 127 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT3 | BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend*/ \ 128 {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \ 129 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ 130 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*Set SDIO suspend local register*/ \ 131 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, /*wait power state to suspend*/ 132 133 #define RTL8723D_TRANS_CARDDIS_TO_CARDEMU \ 134 /* format */ \ 135 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 136 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/ \ 137 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, /*Set SDIO suspend local register*/ \ 138 {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, /*wait power state to suspend*/\ 139 {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \ 140 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\ 141 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ 142 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/ 143 144 145 #define RTL8723D_TRANS_CARDEMU_TO_PDN \ 146 /* format */ \ 147 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 148 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ 149 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK | PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \ 150 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\ 151 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/ 152 153 #define RTL8723D_TRANS_PDN_TO_CARDEMU \ 154 /* format */ \ 155 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 156 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/ 157 158 #define RTL8723D_TRANS_ACT_TO_LPS \ 159 /* format */ \ 160 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 161 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ 162 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/ \ 163 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 164 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 165 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 166 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 167 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled, and clock are gated*/ \ 168 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 169 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/ \ 170 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \ 171 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/ \ 172 {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/ \ 173 {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/ \ 174 175 176 #define RTL8723D_TRANS_LPS_TO_ACT \ 177 /* format */ \ 178 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 179 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\ 180 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\ 181 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\ 182 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\ 183 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*. 0x08[4] = 0 switch TSF to 40M*/\ 184 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0}, /*Polling 0x109[7]=0 TSF in 40M*/\ 185 {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6) | BIT(7), 0}, /*. 0x29[7:6] = 2b'00 enable BB clock*/\ 186 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*. 0x101[1] = 1*/\ 187 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/\ 188 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1) | BIT(0), BIT1 | BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/\ 189 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 190 191 #define RTL8723D_TRANS_END \ 192 /* format */ \ 193 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, / comments here*/ \ 194 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0}, 195 196 197 extern WLAN_PWR_CFG rtl8723D_power_on_flow[RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS]; 198 extern WLAN_PWR_CFG rtl8723D_radio_off_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_END_STEPS]; 199 extern WLAN_PWR_CFG rtl8723D_card_disable_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_CARDDIS_STEPS + RTL8723D_TRANS_END_STEPS]; 200 extern WLAN_PWR_CFG rtl8723D_card_enable_flow[RTL8723D_TRANS_CARDDIS_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS]; 201 extern WLAN_PWR_CFG rtl8723D_suspend_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_SUS_STEPS + RTL8723D_TRANS_END_STEPS]; 202 extern WLAN_PWR_CFG rtl8723D_resume_flow[RTL8723D_TRANS_SUS_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS]; 203 extern WLAN_PWR_CFG rtl8723D_hwpdn_flow[RTL8723D_TRANS_ACT_TO_CARDEMU_STEPS + RTL8723D_TRANS_CARDEMU_TO_PDN_STEPS + RTL8723D_TRANS_END_STEPS]; 204 extern WLAN_PWR_CFG rtl8723D_enter_lps_flow[RTL8723D_TRANS_ACT_TO_LPS_STEPS + RTL8723D_TRANS_END_STEPS]; 205 extern WLAN_PWR_CFG rtl8723D_leave_lps_flow[RTL8723D_TRANS_LPS_TO_ACT_STEPS + RTL8723D_TRANS_END_STEPS]; 206 207 #endif 208