1 2 /****************************************************************************** 3 * 4 * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. 5 * 6 * This program is free software; you can redistribute it and/or modify it 7 * under the terms of version 2 of the GNU General Public License as 8 * published by the Free Software Foundation. 9 * 10 * This program is distributed in the hope that it will be useful, but WITHOUT 11 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 12 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 13 * more details. 14 * 15 * You should have received a copy of the GNU General Public License along with 16 * this program; if not, write to the Free Software Foundation, Inc., 17 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA 18 * 19 * 20 ******************************************************************************/ 21 22 #ifndef __HAL8814PWRSEQ_H__ 23 #define __HAL8814PWRSEQ_H__ 24 25 #include "HalPwrSeqCmd.h" 26 27 /* 28 Check document WB-110628-DZ-RTL8195 (Jaguar) Power Architecture-R04.pdf 29 There are 6 HW Power States: 30 0: POFF--Power Off 31 1: PDN--Power Down 32 2: CARDEMU--Card Emulation 33 3: ACT--Active Mode 34 4: LPS--Low Power State 35 5: SUS--Suspend 36 37 The transision from different states are defined below 38 TRANS_CARDEMU_TO_ACT 39 TRANS_ACT_TO_CARDEMU 40 TRANS_CARDEMU_TO_SUS 41 TRANS_SUS_TO_CARDEMU 42 TRANS_CARDEMU_TO_PDN 43 TRANS_ACT_TO_LPS 44 TRANS_LPS_TO_ACT 45 46 TRANS_END 47 */ 48 #define RTL8814A_TRANS_CARDEMU_TO_ACT_STEPS 16 49 #define RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS 20 50 #define RTL8814A_TRANS_CARDEMU_TO_SUS_STEPS 17 51 #define RTL8814A_TRANS_SUS_TO_CARDEMU_STEPS 15 52 #define RTL8814A_TRANS_CARDEMU_TO_PDN_STEPS 17 53 #define RTL8814A_TRANS_PDN_TO_CARDEMU_STEPS 16 54 #define RTL8814A_TRANS_ACT_TO_LPS_STEPS 20 55 #define RTL8814A_TRANS_LPS_TO_ACT_STEPS 15 56 #define RTL8814A_TRANS_END_STEPS 1 57 58 59 #define RTL8814A_TRANS_CARDEMU_TO_ACT \ 60 /* format */ \ 61 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 62 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/ \ 63 {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1 power ready*/ \ 64 {0x002B, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /* ??0x28[24]=1, enable pll phase select*/ \ 65 {0x0015, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT3|BIT2|BIT1), (BIT3|BIT2|BIT1)},/* 0x14[11:9]=3'b111,OCP current threshold=1.5A */ \ 66 {0x002D, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x0E, 0x08},/* 0x2C[11:9]=3'b100, select lpf R3 */ \ 67 {0x002D, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x70, 0x50},/* 0x2C[14:12]=3'b101, select lpf Rs*/ \ 68 {0x007B, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* 0x78[30]=1'b1, SDM order select*/ \ 69 /*{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0}, */ /* disable HWPDN 0x04[15]=0*/ \ 70 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0},/* disable WL suspend*/ \ 71 {0x00F0, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* */ \ 72 {0x0081, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x30, 0x20},/* */ \ 73 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/ \ 74 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/ 75 76 #define RTL8814A_TRANS_ACT_TO_CARDEMU \ 77 /* format */ \ 78 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 79 {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4 turn off 3-wire */ \ 80 {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4 turn off 3-wire */ \ 81 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /* 0x2[0] = 0 RESET BB, CLOSE RF */ \ 82 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, /*Delay 1us*/ \ 83 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* Whole BB is reset*/ \ 84 {0x1002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /* 0x2[0] = 0 RESET BB, CLOSE RF */ \ 85 {0x0002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, /*Delay 1us*/ \ 86 {0x1002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* Whole BB is reset*/ \ 87 {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*0x1F[7:0] = 0 turn off RF*/ \ 88 /*{0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},*/ /*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */ \ 89 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x28}, /* 0x07[7:0] = 0x28 sps pwm mode 0x2a for BT coex*/ \ 90 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x02, 0}, /*0x8[1] = 0 ANA clk =500k */ \ 91 /*{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0|BIT1, 0},*/ /* 0x02[1:0] = 0 reset BB */ \ 92 {0x0066, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0}, /*0x66[7]=0, disable ckreq for gpio7 output SUS */ \ 93 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x41[4]=0, disable sic for gpio7 output SUS */ \ 94 {0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /*0x42[1]=0, disable ckout for gpio7 output SUS */ \ 95 {0x004e, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x4E[5]=1, disable LED2 for gpio7 output SUS */ \ 96 {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x41[0]=0, disable uart for gpio7 output SUS */ \ 97 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \ 98 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ 99 100 #define RTL8814A_TRANS_CARDEMU_TO_SUS \ 101 /* format */ \ 102 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 103 {0x0061, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x0F, 0x0c},\ 104 {0x0061, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x0F, 0x0E},\ 105 {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x0F, 0x07},/* gpio11 input mode, gpio10~8 output mode */ \ 106 {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */ \ 107 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */ \ 108 {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */ \ 109 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* suspend option all off */ \ 110 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*0x14[13] = 1 turn on ZCD */ \ 111 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* 0x14[14] =1 trun on ZCD */ \ 112 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */ \ 113 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*0x8[1] = 0 ANA clk =500k */ \ 114 {0x0091, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xA0, 0xA0}, /* 0x91[7]=1 0x91[5]=1 , disable sps,ldo sleep mode */ \ 115 {0x0070, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /* 0x70[3]=1 enable mainbias polling */ \ 116 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 1 enable WL suspend */ 117 118 #define RTL8814A_TRANS_SUS_TO_CARDEMU \ 119 /* format */ \ 120 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 121 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 0 enable WL suspend*/ \ 122 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0x10, 0},/*0x23[4] = 0 hpon LDO sleep mode leave */ \ 123 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, 0},/* 0x14[14] =0 trun off ZCD */ \ 124 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0},/*0x14[13] = 0 turn off ZCD */ \ 125 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */ \ 126 {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio11 input mode, gpio10~8 input mode */ 127 128 #define RTL8814A_TRANS_CARDEMU_TO_CARDDIS \ 129 /* format */ \ 130 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 131 /**{0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, //0x194[0]=0 , disable 32K clock*/ \ 132 /**{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x94}, //0x93=0x94 , 90[30] =0 enable 500k ANA clock .switch clock from 12M to 500K , 90 [26] =0 disable EEprom loader clock*/ \ 133 {0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0}, /*0x03[2] = 0, reset 3081*/ \ 134 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x01}, /*0x80=05h if reload fw, fill the default value of host_CPU handshake field*/ \ 135 {0x0081, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x30}, /*0x80=05h if reload fw, fill the default value of host_CPU handshake field*/ \ 136 /*{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xcc},*/ \ 137 /*{0x0042, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xF0, 0xEC},*/ \ 138 /*{0x0043, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x07},*/ /* gpio11 input mode, gpio10~8 output mode */ \ 139 {0x0045, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio 0~7 output same value as input ?? */ \ 140 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xff},/* gpio0~7 output mode */ \ 141 {0x0047, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/* 0x47[7:0] = 00 gpio mode */ \ 142 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* 0x15[6] =1 trun on ZCD output */ \ 143 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*0x15[5] = 1 turn on ZCD */ \ 144 {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, 0},/*0x12[6] = 0 force PFM mode */ \ 145 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4},/*0x23[4] = 1 hpon LDO sleep mode */ \ 146 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*0x8[1] = 0 ANA clk =500k */ \ 147 {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/ \ 148 {0x001f, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* 0x01f[1]=0 , disable RFC_0 control REG_RF_CTRL_8814A */ \ 149 {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* 0x020[1]=0 , disable RFC_1 control REG_RF_CTRL_8814A */ \ 150 {0x0021, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* 0x021[1]=0 , disable RFC_2 control REG_RF_CTRL_8814A */ \ 151 {0x0076, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* 0x076[1]=0 , disable RFC_3 control REG_OPT_CTRL_8814A +2 */ \ 152 {0x0091, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xA0, 0xA0}, /* 0x91[7]=1 0x91[5]=1 , disable sps,ldo sleep mode */ \ 153 {0x0070, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /* 0x70[3]=1 enable mainbias polling */ \ 154 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3}, /*0x04[11] = 1 enable WL suspend*/ 155 156 #define RTL8814A_TRANS_CARDDIS_TO_CARDEMU \ 157 /* format */ \ 158 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 159 {0x0012, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/*0x12[6] = 1 force PWM mode */ \ 160 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0},/*0x15[5] = 0 turn off ZCD */ \ 161 {0x0015, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, 0},/* 0x15[6] =0 trun off ZCD output */ \ 162 {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0},/*0x23[4] = 0 hpon LDO leave sleep mode */ \ 163 {0x0046, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/* gpio0~7 input mode */ \ 164 {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00}, /* gpio11 input mode, gpio10~8 input mode */ \ 165 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0}, /*0x04[10] = 0, enable SW LPS PCIE only*/ \ 166 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, 0}, /*0x04[11] = 0, enable WL suspend*/ \ 167 /*{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2},*/ /*0x03[2] = 1, enable 3081*/ \ 168 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/ \ 169 {0x0071, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/*0x70[10] = 0, CPHY_MBIAS_EN disable*/ 170 171 172 #define RTL8814A_TRANS_CARDEMU_TO_PDN \ 173 /* format */ \ 174 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 175 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/ 176 177 #define RTL8814A_TRANS_PDN_TO_CARDEMU \ 178 /* format */ \ 179 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 180 {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/ 181 182 #define RTL8814A_TRANS_ACT_TO_LPS \ 183 /* format */ \ 184 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 185 {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/ \ 186 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x7F},/*Tx Pause*/ \ 187 {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 188 {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 189 {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 190 {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/ \ 191 {0x0c00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xc00[7:0] = 4 turn off 3-wire */ \ 192 {0x0e00, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x04}, /* 0xe00[7:0] = 4 turn off 3-wire */ \ 193 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated,and RF closed*/ \ 194 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 195 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* Whole BB is reset*/ \ 196 {0x1002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated,and RF closed*/ \ 197 {0x0002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \ 198 {0x1002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0}, /* Whole BB is reset*/ \ 199 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/ \ 200 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/ \ 201 {0x05F1, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Respond TxOK to scheduler*/ 202 203 204 #define RTL8814A_TRANS_LPS_TO_ACT \ 205 /* format */ \ 206 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 207 {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/ \ 208 {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/ \ 209 {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/ \ 210 {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /* Delay*/ \ 211 {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*. 0x08[4] = 0 switch TSF to 40M*/ \ 212 {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /* Polling 0x109[7]=0 TSF in 40M*/ \ 213 /*{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, */ /*. ??0x29[7:6] = 2b'00 enable BB clock*/ \ 214 {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*. 0x101[1] = 1*/ \ 215 {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*. 0x100[7:0] = 0xFF enable WMAC TRX*/ \ 216 {0x0002, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*. 0x02[1:0] = 2b'11 enable BB macro*/ \ 217 {0x1002, ~PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*. 0x1002[1:0] = 2b'11 enable BB macro*/ \ 218 {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*. 0x522 = 0*/ 219 220 #define RTL8814A_TRANS_END \ 221 /* format */ \ 222 /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/ \ 223 {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, // 224 225 226 extern WLAN_PWR_CFG rtl8814A_power_on_flow[RTL8814A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8814A_TRANS_END_STEPS]; 227 extern WLAN_PWR_CFG rtl8814A_radio_off_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_END_STEPS]; 228 extern WLAN_PWR_CFG rtl8814A_card_disable_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8814A_TRANS_END_STEPS]; 229 extern WLAN_PWR_CFG rtl8814A_card_enable_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8814A_TRANS_END_STEPS]; 230 extern WLAN_PWR_CFG rtl8814A_suspend_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8814A_TRANS_END_STEPS]; 231 extern WLAN_PWR_CFG rtl8814A_resume_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8814A_TRANS_END_STEPS]; 232 extern WLAN_PWR_CFG rtl8814A_hwpdn_flow[RTL8814A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8814A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8814A_TRANS_END_STEPS]; 233 extern WLAN_PWR_CFG rtl8814A_enter_lps_flow[RTL8814A_TRANS_ACT_TO_LPS_STEPS+RTL8814A_TRANS_END_STEPS]; 234 extern WLAN_PWR_CFG rtl8814A_leave_lps_flow[RTL8814A_TRANS_LPS_TO_ACT_STEPS+RTL8814A_TRANS_END_STEPS]; 235 236 #endif //__HAL8814PWRSEQ_H__ 237 238