Home
last modified time | relevance | path

Searched refs:client (Results 1 – 25 of 30) sorted by relevance

12

/rk3399_rockchip-uboot/doc/device-tree-bindings/mailbox/
H A Dmailbox.txt1 * Generic Mailbox Controller and client driver bindings
4 assign appropriate mailbox channel to client drivers.
H A Dnvidia,tegra186-hsp.txt32 The mbox specifier of the "mboxes" property in the client node should
34 one should be the ID that the client is going to use. Those information
49 client {
/rk3399_rockchip-uboot/doc/device-tree-bindings/pinctrl/
H A Dpinctrl-bindings.txt9 designated client devices. Again, each client device must be represented as a
12 For a client device to operate correctly, certain pin controllers must
13 set up certain specific pin configurations. Some client devices need a
16 device is inactive. Hence, each client device can define a set of named
17 states. The number and names of those states is defined by the client device's
21 for client device device tree nodes to map those state names to the pin
24 Note that pin controllers themselves may also be client devices of themselves.
27 in a single place, rather than splitting it across multiple client device
30 bindings for the individual client devices in use by that board, i.e. whether
33 == Pinctrl client devices ==
[all …]
H A Datmel,at91-pio4-pinctrl.txt11 common pinctrl bindings used by client devices.
H A Drockchip,pinctrl.txt9 common pinctrl bindings used by client devices, including the meaning of the
/rk3399_rockchip-uboot/doc/
H A DREADME.android-fastboot14 The counterpart to this gadget is the fastboot client which can
42 the fastboot client. The list of vendor IDs supported can be found in the
43 fastboot client source code (fastboot.c) mentioned above.
106 On the client side you can fetch the bootloader version for instance:
114 and once the client comes back, the board should reset.
118 fastboot client wrap the Android suite around it. On OMAP for instance you
119 take zImage kernel and pass it to the fastboot client:
H A DREADME.esbc_validate11 signature of images (Boot Script and ESBC uboot client).
23 2. ESBC uboot client can be linux. Additionally, rootfs and device
H A DREADME.android-fastboot-protocol46 3. Data phase. Depending on the command, the host or client will
49 until the client has sent or received the number of bytes indicated
113 by "boot", "ramdisk", "flash", etc. The client
147 The "getvar:%s" command is used to read client variables which
H A DREADME.nvme13 for enterprise and client solid state drives, typically attached to the PCI
15 address the needs of enterprise and client systems that utilize PCI express
H A DREADME.usb75 client. In that case your board is pretending to be an Ethernet adapter
192 DHCP client bound to address 172.22.73.81
H A DREADME.pxe202 When a pxe client retrieves and boots the default pxe file,
H A DREADME.odroid194 DHCP client bound to address 192.168.1.10 (524 ms)
/rk3399_rockchip-uboot/Documentation/devicetree/bindings/phy/
H A Dno-op.txt4 This is useful when the 'client' driver (USB, SATA, ...) uses the PHY framework
/rk3399_rockchip-uboot/drivers/firmware/scmi/
H A DKconfig16 Communications between agent (client) and the SCMI server are
/rk3399_rockchip-uboot/doc/device-tree-bindings/gpio/
H A Dgpio-samsung.txt9 - #gpio-cells: Should be 4. The syntax of the gpio specifier used by client nodes
H A Dgpio-pcf857x.txt58 bindings used by client devices.
H A Dnvidia,tegra186-gpio.txt27 documentation for rationale. Any particular GPIO client is expected to access
/rk3399_rockchip-uboot/drivers/ddr/marvell/a38x/
H A Dddr3_training_ip.h159 u8 client; member
/rk3399_rockchip-uboot/include/
H A Dconfig_distro_bootcmd.h241 #error Please specify an EFI client identifier
/rk3399_rockchip-uboot/doc/device-tree-bindings/clock/
H A Drockchip,rk3288-cru.txt20 Each clock is assigned an identifier and client nodes can use this identifier
H A Drockchip,rk3188-cru.txt21 Each clock is assigned an identifier and client nodes can use this identifier
/rk3399_rockchip-uboot/board/bosch/shc/
H A DREADME94 DHCP client bound to address 192.168.20.91 (258 ms)
/rk3399_rockchip-uboot/board/intel/
H A DKconfig56 a USB client port.
/rk3399_rockchip-uboot/doc/SPL/
H A DREADME.am335x-network49 Identifier (VCI) set by BOOTP client (RBL sets VCI to "DM814x ROM v1.0"
/rk3399_rockchip-uboot/doc/device-tree-bindings/gpu/
H A Dnvidia,tegra20-host1x.txt20 of the following host1x client modules:

12