| /rk3399_rockchip-uboot/drivers/serial/ |
| H A D | serial_zynq.c | 50 unsigned long clock, unsigned long baud) in _uart_zynq_serial_setbrg() argument
57 if (clock < 1000000 && baud > 4800) in _uart_zynq_serial_setbrg()
58 baud = 4800; in _uart_zynq_serial_setbrg()
67 bgen = clock / (baud * (bdiv + 1)); in _uart_zynq_serial_setbrg()
77 if (baud > calc_baud) in _uart_zynq_serial_setbrg()
78 calc_bauderror = baud - calc_baud; in _uart_zynq_serial_setbrg()
80 calc_bauderror = calc_baud - baud; in _uart_zynq_serial_setbrg()
81 if (((calc_bauderror * 100) / baud) < 3) in _uart_zynq_serial_setbrg()
|
| H A D | serial_ar933x.c | 58 static void ar933x_serial_get_scale_step(u32 clk, u32 baud, in ar933x_serial_get_scale_step() argument
67 min_diff = baud; in ar933x_serial_get_scale_step()
72 tstep = baud * (tscale + 1); in ar933x_serial_get_scale_step()
80 diff = abs(baudrate - baud); in ar933x_serial_get_scale_step()
|
| H A D | serial_bcm283x_mu.c | 41 u32 baud; member
68 writel(divider - 1, ®s->baud); in bcm283x_mu_serial_setbrg()
|
| H A D | serial_lpuart.c | 224 tmp = in_le32(&base->baud); in _lpuart32_serial_setbrg_7ulp()
238 out_le32(&base->baud, tmp); in _lpuart32_serial_setbrg_7ulp()
251 lpuart_write32(plat->flags, &base->baud, sbr); in _lpuart32_serial_setbrg()
|
| /rk3399_rockchip-uboot/doc/device-tree-bindings/serial/ |
| H A D | bcm2835-aux-uart.txt | 6 - clock: input clock frequency for the UART (used to calculate the baud
10 - skip-init: if present, the baud rate divisor is not changed
|
| H A D | pl01x.txt | 6 - clock: input clock frequency for the UART (used to calculate the baud
10 - skip-init: if present, the baud rate divisor is not changed
|
| /rk3399_rockchip-uboot/include/ |
| H A D | fsl_lpuart.h | 14 u32 baud; member
25 u32 baud; member
|
| /rk3399_rockchip-uboot/board/astro/mcf5373l/ |
| H A D | mcf5373l.c | 89 int rs_serial_init(int port, int baud) in rs_serial_init() argument
126 counter = (u32) (gd->bus_clk / (baud)); in rs_serial_init()
|
| H A D | astro.h | 5 int rs_serial_init(int port, int baud);
|
| /rk3399_rockchip-uboot/arch/x86/include/asm/acpi/ |
| H A D | debug.asl | 33 Store(0x01, CDAT) /* 115200 baud (low) */
34 Store(0x00, CDLM) /* 115200 baud (high) */
|
| /rk3399_rockchip-uboot/doc/ |
| H A D | README.vxworks | 62 It's very common that VxWorks BSPs configure a different baud rate for the
64 to use 9600 as the default baud rate on all x86 BSPs while U-Boot uses 115200.
65 Please configure both U-Boot and VxWorks to use the same baud rate, or it may
|
| H A D | README.AMCC-eval-boards-cleanup | 11 o Use 115200 baud as default console baudrate.
|
| H A D | README.generic-board | 45 things like setting up the baud rate requires a change in 10 separate
|
| /rk3399_rockchip-uboot/arch/x86/cpu/baytrail/ |
| H A D | Kconfig | 34 A maximum baud rate of 115200 bps is supported. For this
|
| /rk3399_rockchip-uboot/disk/ |
| H A D | part_amiga.h | 136 u32 baud; member
|
| /rk3399_rockchip-uboot/drivers/i2c/ |
| H A D | mvtwsi.c | 448 uint baud = 0x44; /* Baud rate after controller reset */ in __twsi_i2c_set_bus_speed() local
460 baud = (m << 3) | n; in __twsi_i2c_set_bus_speed()
464 writel(baud, &twsi->baudrate); in __twsi_i2c_set_bus_speed()
|
| /rk3399_rockchip-uboot/drivers/spi/ |
| H A D | pic32_spi.c | 30 struct pic32_reg_atomic baud; member
301 writel(div, &priv->regs->baud.raw); in pic32_spi_set_speed()
|
| /rk3399_rockchip-uboot/arch/x86/include/asm/ |
| H A D | coreboot_tables.h | 98 u32 baud; member
|
| /rk3399_rockchip-uboot/arch/arm/dts/ |
| H A D | imx6sll.dtsi | 310 clock-names = "ipg", "baud";
323 clock-names = "ipg", "baud";
336 clock-names = "ipg", "baud";
|
| H A D | imx6sl.dtsi | 263 clock-names = "ipg", "baud";
279 clock-names = "ipg", "baud";
295 clock-names = "ipg", "baud";
|
| H A D | imx6qdl.dtsi | 348 clock-names = "ipg", "baud";
364 clock-names = "ipg", "baud";
380 clock-names = "ipg", "baud";
|
| H A D | imx6sx.dtsi | 321 clock-names = "ipg", "baud";
335 clock-names = "ipg", "baud";
349 clock-names = "ipg", "baud";
|
| /rk3399_rockchip-uboot/board/cadence/xtfpga/ |
| H A D | README | 44 The serial port defaults to 115200 baud, no parity and 1 stop bit.
|
| /rk3399_rockchip-uboot/board/sbc8349/ |
| H A D | README | 109 will change the baud clocks and mess up your serial console output if you
|
| /rk3399_rockchip-uboot/board/sbc8548/ |
| H A D | README | 32 will change the baud clocks and mess up your serial console output if you
|