| /OK3568_Linux_fs/kernel/drivers/atm/ |
| H A D | horizon.c | 467 PRINTD (DBG_REGS, "CONTROL 0: %#x", rd_regl (dev, CONTROL_0_REG)); in dump_regs()
468 PRINTD (DBG_REGS, "RX CONFIG: %#x", rd_regw (dev, RX_CONFIG_OFF)); in dump_regs()
469 PRINTD (DBG_REGS, "TX CONFIG: %#x", rd_regw (dev, TX_CONFIG_OFF)); in dump_regs()
470 PRINTD (DBG_REGS, "TX STATUS: %#x", rd_regw (dev, TX_STATUS_OFF)); in dump_regs()
471 PRINTD (DBG_REGS, "IRQ ENBLE: %#x", rd_regl (dev, INT_ENABLE_REG_OFF)); in dump_regs()
472 PRINTD (DBG_REGS, "IRQ SORCE: %#x", rd_regl (dev, INT_SOURCE_REG_OFF)); in dump_regs()
588 PRINTD (DBG_QOS|DBG_FLOW, "make_rate b=%lu, c=%u, %s", br, c, in make_rate()
593 PRINTD (DBG_QOS|DBG_ERR, "zero rate is not allowed!"); in make_rate()
626 PRINTD (DBG_QOS, "A: p=%u, d=%u", pre, div); in make_rate()
650 PRINTD (DBG_QOS, "B: p=%u, d=%u", pre, div); in make_rate()
[all …]
|
| H A D | ambassador.c | 297 PRINTD (DBG_FLOW|DBG_REGS, "wr: %08zx <- %08x", addr, data); in wr_plain()
311 PRINTD (DBG_FLOW|DBG_REGS, "rd: %08zx -> %08x", addr, data); in rd_plain()
317 PRINTD (DBG_FLOW|DBG_REGS, "wr: %08zx <- %08x b[%08x]", addr, data, be); in wr_mem()
332 PRINTD (DBG_FLOW|DBG_REGS, "rd: %08zx -> %08x b[%08x]", addr, data, be); in rd_mem()
342 PRINTD (DBG_REGS, "reading PLX control: "); in dump_registers()
345 PRINTD (DBG_REGS, "reading mailboxes: "); in dump_registers()
348 PRINTD (DBG_REGS, "reading doorb irqev irqen reset:"); in dump_registers()
439 PRINTD (DBG_FLOW|DBG_TX, "tx_complete %p %p", dev, tx); in tx_complete()
463 PRINTD (DBG_FLOW|DBG_RX, "rx_complete %p %p (len=%hu)", dev, rx, rx_len); in rx_complete()
491 … PRINTD (DBG_INFO|DBG_RX, "dropped thanks to atm_charge (vc %hu, truesize %u)", vc, skb->truesize); in rx_complete()
[all …]
|
| H A D | horizon.h | 62 #define PRINTD(bits,format,args...) \ macro
67 #define PRINTD(bits,format,args...) macro
|
| H A D | ambassador.h | 61 #define PRINTD(bits,format,args...) \ macro
66 #define PRINTD(bits,format,args...) macro
|
| /OK3568_Linux_fs/u-boot/drivers/i2c/ |
| H A D | soft_i2c.c | 110 #define PRINTD(fmt,args...) do { \ macro
114 #define PRINTD(fmt,args...) macro
333 PRINTD("i2c_read: chip %02X addr %02X alen %d buffer %p len %d\n", in soft_i2c_read()
350 PRINTD("i2c_read: fix addr_overflow: chip %02X addr %02X\n", in soft_i2c_read()
364 PRINTD("i2c_read, no chip responded %02X\n", chip); in soft_i2c_read()
370 PRINTD("i2c_read, address not <ACK>ed\n"); in soft_i2c_read()
409 PRINTD("i2c_write: chip %02X addr %02X alen %d buffer %p len %d\n", in soft_i2c_write()
415 PRINTD("i2c_write, no chip responded %02X\n", chip); in soft_i2c_write()
421 PRINTD("i2c_write, address not <ACK>ed\n"); in soft_i2c_write()
|
| /OK3568_Linux_fs/u-boot/drivers/spi/ |
| H A D | soft_spi_legacy.c | 21 #define PRINTD(fmt,args...) printf (fmt ,##args) macro
23 #define PRINTD(fmt,args...) macro
124 PRINTD("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n", in spi_xfer()
|
| /OK3568_Linux_fs/u-boot/scripts/kconfig/ |
| H A D | zconf.y | 18 #define PRINTD 0x0001 macro
21 int cdebug = PRINTD;
|
| H A D | zconf.tab.c | |
| H A D | zconf.tab.c_shipped | 91 #define PRINTD 0x0001
94 int cdebug = PRINTD;
|
| /OK3568_Linux_fs/kernel/scripts/kconfig/ |
| H A D | parser.y | 18 #define PRINTD 0x0001 macro
21 int cdebug = PRINTD;
|
| /OK3568_Linux_fs/buildroot/support/kconfig/ |
| H A D | zconf.y | 18 #define PRINTD 0x0001 macro
21 int cdebug = PRINTD;
|
| H A D | zconf.tab.c_shipped | 83 #define PRINTD 0x0001
86 int cdebug = PRINTD;
|