Kconfig - OpenGrok cross reference for /rk3399_rockchip-uboot/drivers/serial/Kconfig

24 	  during serial port initialization (default y). Set this to n on
33 	  large. In this case the debug UART can still be used in some cases.
43 	  large. In this case the debug UART can still be used in some cases.
109 	  - Make sure your UART supports this interface
111 	  - Enable the CONFIG for your UART to tell it to provide this interface
117 	  Depending on your platform it may be possible to use this UART before
120 	  If your UART does not support this interface you can probably add
124 	  You must not use this UART once driver model is working and the
136 	  Select this to enable a debug UART using the altera_jtag_uart driver.
137 	  You will need to provide parameters to make this work. The driver will
143 	  Select this to enable a debug UART using the altera_uart driver.
144 	  You will need to provide parameters to make this work. The driver will
151 	  Select this to enable a debug UART using the ar933x uart driver.
152 	  You will need to provide parameters to make this work. The
159 	  Select this to enable a debug UART using the atmel usart driver. You
160 	  will need to provide parameters to make this work. The driver will
167 	  Select this to enable a debug UART on BCM6345 SoCs. You
168 	  will need to provide parameters to make this work. The driver will
174 	  Select this to enable a debug UART using the ns16550 driver. You
175 	  will need to provide parameters to make this work. The driver will
182 	  Select this to enable a debug console which calls back to EFI to
190 	  Select this to enable a debug UART using the serial_s5p driver. You
191 	  will need to provide parameters to make this work. The driver will
198 	  Select this to enable a debug UART using the serial_meson driver. You
199 	  will need to provide parameters to make this work. The driver will
205 	  Select this to enable a debug UART using the serial_uartlite driver.
206 	  You will need to provide parameters to make this work. The driver will
212 	  Select this to enable a debug UART using the ARM JTAG DCC port.
215 	  any serial interface this is the easiest way how to get console.
223 	  Select this to enable a debug UART using the serial_mvebu driver. You
224 	  will need to provide parameters to make this work. The driver will
230 	  Select this to enable a debug UART using the serial_zynq driver. You
231 	  will need to provide parameters to make this work. The driver will
238 	  Select this to enable a debug UART using the serial_leon3 driver. You
239 	  will need to provide parameters to make this work. The driver will
245 	  Select this to enable a debug UART using the pl01x driver with the
246 	  PL010 UART type. You will need to provide parameters to make this
253 	  Select this to enable a debug UART using the pl01x driver with the
254 	  PL011 UART type. You will need to provide parameters to make this
262 	  Select this to enable a debug UART using the serial_pic32 driver. You
263 	  will need to provide parameters to make this work. The driver will
270 	  Select this to enable a debug UART using the serial_mxc driver. You
271 	  will need to provide parameters to make this work. The driver will
278 	  Select this to enable a debug UART using the UniPhier on-chip UART.
279 	  You will need to provide DEBUG_UART_BASE to make this work.  The
286 	  Select this to enable a debug UART using the omap ns16550 driver.
287 	  You will need to provide parameters to make this work. The driver
306 	  circuitry. The baud rate is derived from this by dividing the input
319 	  value. Use this value to specify the shift to use, where 0=byte
328 	  this option is enabled, the function board_debug_uart_init() will
337 	  Enable this option to show a message when the debug UART is ready
346 	  Select this if the UART you want to use for debug output is already
359 	  Select this to enable an JTAG UART for Altera devices.The JTAG UART
378 	  Select this to enable an UART for Altera devices. Please find
385 	  Select this to enable UART support for QCA/Atheros ar933x
393 	  Select this to enable USART support for Atmel SoCs. It can be
401 	  Select this to enable UART on BCM6345 SoCs.
406 	  Select this to enable a Low Power UART for Freescale VF610 and
413 	  Choose this option to add support for UART driver on the Marvell
421 	  can enable its onboard serial port by enabling this option.
446 	  Select this to enable a UART for Intel MID platforms.
453 	  Select this to enable a debug UART for Rockchip devices when using
462 	  Select this to enable a seral UART for sandbox. This is required to
482 	  Select this to enable Renesas SCIF UART. To operate serial ports
483 	  on systems with RCar or SH SoCs, say Y to this option. If unsure,
492 	  serial ports, say Y to this option. If unsure, say N.
499 	  serial ports, say Y to this option. If unsure, say N.
506 	  serial ports, say Y to this option. If unsure, say N.
521 	  can enable its onboard serial ports by enabling this option.
527 	  Select this to enable Asynchronous Serial Controller available
536 	  onboard serial ports, say Y to this option. If unsure, say N.