141 		sd_err(("%s: out of memory, malloced %d bytes\n", __FUNCTION__, MALLOCED(osh)));  in sdioh_attach()
147 		sd_err(("%s: spi_osinit() failed\n", __FUNCTION__));  in sdioh_attach()
177 		sd_err(("%s: spi_hw_attach() failed\n", __FUNCTION__));  in sdioh_attach()
185 		sd_err(("%s: bcmspi_driver_init() failed()\n", __FUNCTION__));  in sdioh_attach()
195 		sd_err(("%s: spi_register_irq() failed for irq = %d\n", __FUNCTION__, irq));  in sdioh_attach()
214 		sd_err(("%s: detaching from hardware\n", __FUNCTION__));  in sdioh_detach()
293 		sd_err(("%s: Failed to set dwordmode in gSPI\n", __FUNCTION__));  in sdioh_dwordmode()
309 		sd_err(("%s: Failed to set dwordmode in gSPI\n", __FUNCTION__));  in sdioh_dwordmode()
452 			sd_err(("%s: set clock failed\n", __FUNCTION__));  in sdioh_iovar_op()
494 			sd_err(("%s: Failed changing highspeed mode to %d.\n",  in sdioh_iovar_op()
562 				sd_err(("%s: Unable to set response delay.\n", __FUNCTION__));  in sdioh_iovar_op()
570 			sd_err(("%s: Unable to set response delay.\n", __FUNCTION__));  in sdioh_iovar_op()
604 			sd_err(("sdioh_cfg_read() failed.\n"));  in sdioh_cfg_write()
635 		sd_err(("%s: Unable to set sb-addr-windows\n", __FUNCTION__));  in sdioh_cis_read()
643 		sd_err(("%s: Unable to set sb-addr-windows\n", __FUNCTION__));  in sdioh_cis_read()
651 			sd_err(("%s: regread failed: Can't read CIS\n", __FUNCTION__));  in sdioh_cis_read()
748 			sd_err(("%s: bcmspi_card_buf %s failed\n",  in sdioh_request_buffer()
800 		sd_err(("%s: Host is %d bit spid, could not create SPI command.\n",  in bcmspi_card_byterewrite()
825 		sd_err(("%s: Host is %d bit machine, could not read SPI dstatus.\n",  in bcmspi_card_byterewrite()
890 		sd_err(("%s: Host is %d bit machine, could not read SPI dstatus.\n",  in bcmspi_resync_f1()
930 		sd_err(("FIFO underflow happened due to current F2 read command.\n"));  in bcmspi_update_stats()
935 		sd_err(("FIFO overflow happened due to current (F1/F2) write command.\n"));  in bcmspi_update_stats()
938 		sd_err(("Recovering from F1 FIFO overflow.\n"));  in bcmspi_update_stats()
948 		sd_err(("Interrupt from F3.  SW should clear corresponding IntStatus bits\n"));  in bcmspi_update_stats()
953 		sd_err(("Error in CMD or Host data, detected by CRC/Checksum (optional)\n"));  in bcmspi_update_stats()
966 		sd_err(("Packet is available/ready in F3 TX FIFO\n"));  in bcmspi_update_stats()
967 		sd_err(("Packet length = %d\n",  in bcmspi_update_stats()
1054 		sd_err(("spi_start_clock failed\n"));  in bcmspi_client_init()
1060 		sd_err(("spi_start_clock failed\n"));  in bcmspi_client_init()
1067 		sd_err(("bcmspi_host_device_init_adapt failed\n"));  in bcmspi_client_init()
1072 		sd_err(("bcmspi_test_card failed\n"));  in bcmspi_client_init()
1092 		sd_err(("%s: Unable to set response delay for all fun's.\n", __FUNCTION__));  in bcmspi_client_init()
1100 		sd_err(("spi_start_clock failed\n"));  in bcmspi_client_init()
1112 			sd_err(("older corerev < 4 so use the same resp delay for all funcs\n"));  in bcmspi_client_init()
1119 			sd_err(("new corerev >= 4 so set the resp delay for each of the funcs\n"));  in bcmspi_client_init()
1126 				sd_err(("%s: Unable to set response delay for F0\n", __FUNCTION__));  in bcmspi_client_init()
1132 				sd_err(("%s: Unable to set response delay for F1\n", __FUNCTION__));  in bcmspi_client_init()
1138 				sd_err(("%s: Unable to set response delay for F2\n", __FUNCTION__));  in bcmspi_client_init()
1144 				sd_err(("%s: Unable to set response delay for F2\n", __FUNCTION__));  in bcmspi_client_init()
1280 			sd_err(("Spid power was left on but signature read failed."  in bcmspi_host_device_init_adapt()
1335 			sd_err(("Stale spid reg values read as it was kept powered. Value read ="  in bcmspi_host_device_init_adapt()
1370 		sd_err(("Write-Read spid failed. Value wrote = 0x%x, Value read = 0x%x\n",  in bcmspi_test_card()
1383 		sd_err(("Write-Read spid failed. Value wrote = 0x%x, Value read = 0x%x\n",  in bcmspi_test_card()
1565 		sd_err(("Host is %d bit spid, could not create SPI command.\n",  in bcmspi_cmd_issue()
1622 		sd_err(("Unaligned data len %d, hostlen %d\n",  in bcmspi_cmd_issue()
1653 		sd_err(("Host is %d bit machine, could not read SPI dstatus.\n",  in bcmspi_cmd_issue()
1658 		sd_err(("looks like not a GSPI device or device is not powered.\n"));  in bcmspi_cmd_issue()
1710 					sd_err(("F2 FIFO is not ready to receive data.\n"));  in bcmspi_card_buf()
1751 		sd_err(("%s: cmd_issue failed for %s\n", __FUNCTION__,  in bcmspi_card_buf()