Merge u-boot/master into u-boot-ti/master

In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (whic

Merge u-boot/master into u-boot-ti/master

In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.

Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

powerpc/83xx/km: drop uneeded dtt_bus environment var

There is no need for a environment variable to configure the dtt bus.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>

powerpc/83xx/km: add MV88E6122 switch support for kmvect1

kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport

powerpc/83xx/km: add MV88E6122 switch support for kmvect1

kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).

The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.

Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>

show more ...

Merge git://git.denx.de/u-boot

km83xx: add common support for km8309 boards

Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#else

km83xx: add common support for km8309 boards

Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

* 'master' of git://git.denx.de/u-boot-mpc83xx:
km/common: check test_bank and testpin for testboot
powerpc/83xx/km: readout dip_switch

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

* 'master' of git://git.denx.de/u-boot-mpc83xx:
km/common: check test_bank and testpin for testboot
powerpc/83xx/km: readout dip_switch on kmcoge5ne
powerpc/83xx: configure CONFIG_POST for kmcoge5ne
powerpc/83xx/km: added missing enable of application buffer
km/common: increase bootlimit to 3
km/common: fixed error in ethaddr (1-byte-shift)
MAINTAINERS: cleanup for keymile boards
powerpc/83xx: add kmcoge5ne board support
km/common: add support for second flash
powerpc83xx/km: remove unneeded CONFIG_PCI for kmeter1
powerpc83xx/km: lock the window size to 2GiB befor fixing sdram size
powerpc/83xx/km: use tuxx1.h for kmsupx5 target
powerpc/83xx: increment malloc heap size for the MPC832x MDS boards

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

powerpc/83xx: add kmcoge5ne board support

This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application cod

powerpc/83xx: add kmcoge5ne board support

This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.

Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

km/common: add support for second flash

Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to

km/common: add support for second flash

Add support for a second flash.
By default, a single flash chip is set up:
- called 'boot'
- mtd name for ubi 'ubi0'
MTDIDS and MTDPARTS may be overwritten to add a second flash.
The 'ubiattach' command is featured in two versions:
- if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined:
this is the version as up to now
- if CONFIG_KM_UBI_PARTITION_NAME_APP is defined:
a check on 'actual_bank' will be done to determine the flash to boot
from.

Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and
CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader
and the applications.

Example:
In the board config do:
... snip ...

"boot:" \
"768k(u-boot)," \
"128k(env)," \
"128k(envred)," \
"-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \
"app:" \
"-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");"

... snap ...

You may also need to enable the second flash:
... snip ...
/* additional featured for COGE5 */
... snap ...

Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

* 'master' of git://git.denx.de/u-boot-mpc83xx:
powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
powerpc/mpc83xx: Add 512MB DDR sup

Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx

* 'master' of git://git.denx.de/u-boot-mpc83xx:
powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds
powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds
mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code
mpc83xx: Cleanup usage of LBC constants
mpc83xx: Cleanup usage of DDR constants
mpc83xx: Cleanup usage of BAT constants
mpc83xx: cosmetic: vme8349.h checkpatch compliance
mpc83xx: cosmetic: ve8313.h checkpatch compliance
mpc83xx: cosmetic: sbc8349.h checkpatch compliance
mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance
mpc83xx: cosmetic: kmeter1.h checkpatch compliance
mpc83xx: cosmetic: TQM834x.h checkpatch compliance
mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance
mpc83xx: cosmetic: MVBLM7.h checkpatch compliance
mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance
mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance
mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance
mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance
mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance
mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance
mpc83xx: Fix ipic structure definition
powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions
cosmetic, powerpc, mpc83xx: checkpatch cleanup
powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c
mpc83xx: fix global timer structure definition

show more ...

mpc83xx: Cleanup usage of LBC constants

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.co

mpc83xx: Cleanup usage of LBC constants

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

mpc83xx: Cleanup usage of BAT constants

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.co

mpc83xx: Cleanup usage of BAT constants

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

show more ...

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysing

board configs: drop NET_MULTI references

Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

show more ...

Drop bogus BOOTFLAG_* definitions

There is no code anywhere that references BOOTFLAG_* so remove these
defines.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valenti

Drop bogus BOOTFLAG_* definitions

There is no code anywhere that references BOOTFLAG_* so remove these
defines.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Peter Tyser <ptyser@xes-inc.com>

show more ...

km/common: simplify debug environment

The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the defa

km/common: simplify debug environment

The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the default environment:
run develop: this configures the environment to setup the
rootfs via nfs
run ramfs: this configures the environment to setup the
rootfs in ram

Each architecture now has a "arch" variable which is used
to load the architecture specific debug scripts and to set
the rootpath for NFS.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>

show more ...

keymile boards: move keymile specific header in subdir

Collect all keymile specific common headers in include/configs/km.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Valentin Longcham

keymile boards: move keymile specific header in subdir

Collect all keymile specific common headers in include/configs/km.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>

show more ...