Merge branch 'next-dev' into thunder-boot

UPSTREAM: usb: dwc3: Add Meson G12A USB Glue

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and US

UPSTREAM: usb: dwc3: Add Meson G12A USB Glue

Adds support for Amlogic G12A USB Control Glue HW.

The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only

A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.

The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.

This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.

Change-Id: I099bb5fbda0fdd52c4d78e32f879f8324bda4c59
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
(cherry picked from commit adb049abf7a209629c7b5e4bc673a0d802c616c2)

show more ...

UPSTREAM: usb: dwc3: Add generic DWC3 glue logic driver

By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse node

UPSTREAM: usb: dwc3: Add generic DWC3 glue logic driver

By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.

Change-Id: I946ce3749b0323302426b9a08c70f37297654e33
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
(cherry picked from commit 49d674547c5bf668802b4b6a24218205fed957f0)

show more ...

UPSTREAM: usb: dwc3: add UniPhier specific glue layer

Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.

Change-Id: I51194b1b15860f2813029b53ad7e5deec63344ff
S

UPSTREAM: usb: dwc3: add UniPhier specific glue layer

Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.

Change-Id: I51194b1b15860f2813029b53ad7e5deec63344ff
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
(cherry picked from commit dc04b35ef2c8c04cb362758ec467777348ef3f15)

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

usb: dwc3: Makefile: Don't build gadget code if USB_GADGET is disabled

It is pointless to build gadget driver if USB_GADGET is disabled.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek

usb: dwc3: Makefile: Don't build gadget code if USB_GADGET is disabled

It is pointless to build gadget driver if USB_GADGET is disabled.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>

show more ...

Merge git://git.denx.de/u-boot

Various Makefiles: Add SPDX-License-Identifier tags

After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours

Various Makefiles: Add SPDX-License-Identifier tags

After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge git://git.denx.de/u-boot-usb

samsung: usb: phy: Support for DWC3 PHY

New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.

This code is used t

samsung: usb: phy: Support for DWC3 PHY

New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.

This code is used thereafter in the board_usb_init() call.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>

show more ...

usb: dwc3: Makefile: Make dwc3 driver compile in u-boot

Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.

Signed-off

usb: dwc3: Makefile: Make dwc3 driver compile in u-boot

Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

show more ...

usb: dwc3: remove trace_* APIs from dwc3 driver

Removed most of the trace_* APIs from dwc3 driver since tracepoints are not
supported in u-boot. Replaced some of the trace_* API with dev_dbg/dev/vdb

usb: dwc3: remove trace_* APIs from dwc3 driver

Removed most of the trace_* APIs from dwc3 driver since tracepoints are not
supported in u-boot. Replaced some of the trace_* API with dev_dbg/dev/vdbg.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Review-by: Lukasz Majewski <l.majewski@samsung.com>

show more ...

usb: dwc3: add dwc3 folder from linux kernel to u-boot

Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9)
to u-boot. This will be adapted to work with u-boot in the
following patches.

Signed

usb: dwc3: add dwc3 folder from linux kernel to u-boot

Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9)
to u-boot. This will be adapted to work with u-boot in the
following patches.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>

show more ...