env: Rename setenv() to env_set()

We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd

env: Rename setenv() to env_set()

We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing function

dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: core: Replace of_offset with accessor

At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree,

dm: core: Replace of_offset with accessor

At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

dm: eth: Avoid blocking on packet reception

Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
thi

dm: eth: Avoid blocking on packet reception

Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.

At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.

Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

net: cosmetic: Change IPaddr_t to struct in_addr

This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses

net: cosmetic: Change IPaddr_t to struct in_addr

This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>

show more ...

sandbox: eth: Add support for using the 'lo' interface

The 'lo' interface on Linux doesn't support thinks like ARP or
link-layer access like we use to talk to a normal network interface.
A higher-le

sandbox: eth: Add support for using the 'lo' interface

The 'lo' interface on Linux doesn't support thinks like ARP or
link-layer access like we use to talk to a normal network interface.
A higher-level network API must be used to access localhost.

As written, this interface is limited to not supporting ICMP since the
API doesn't allow the socket to be opened for all IP traffic and be able
to receive at the same time. UDP is far more useful to test with, so it
was selected over ICMP. Ping won't work, but things like TFTP should
work.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

sandbox: eth: Add a bridge to a real network for sandbox

Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host

sandbox: eth: Add a bridge to a real network for sandbox

Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.

This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:

sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...