block: pass block dev not num to read/write/erase()

This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC

block: pass block dev not num to read/write/erase()

This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'u-boot/master'

Conflicts:
drivers/net/Makefile

(trivial merge)

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

driver: Add support of image load for MMC & SPI in SPL

Add support of loading image, binary for MMC and SPI during SPL boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by:

driver: Add support of image load for MMC & SPI in SPL

Add support of loading image, binary for MMC and SPI during SPL boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

driver/mmc: fix compile warnings

Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.

driver/mmc: fix compile warnings

Fix following compile warnings
fsl_esdhc_spl.c: In function 'mmc_boot':
fsl_esdhc_spl.c:35:10: warning: unused variable 'byte_num' [-Wunused-variable]
fsl_esdhc_spl.c:35:7: warning: unused variable 'i' [-Wunused-variable]
fsl_esdhc_spl.c:34:8: warning: unused variable 'val' [-Wunused-variable]
fsl_esdhc_spl.c:33:6: warning: unused variable 'blklen' [-Wunused-variable]
fsl_esdhc_spl.c:105:7: warning: 'tmp_buf' may be used uninitialized in this
function [-Wuninitialized]

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mmc

powerpc: mmc: Add corenet devices support in esdhc spl

Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such h

powerpc: mmc: Add corenet devices support in esdhc spl

Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.

So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

SPDX-License-Identifier: clean up license header

This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c

Sign

SPDX-License-Identifier: clean up license header

This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c

Signed-off-by: York Sun <yorksun@freescale.com>

show more ...

powerpc: mpc85xx: Support booting from SD Card with SPL

The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeab

powerpc: mpc85xx: Support booting from SD Card with SPL

The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

show more ...