dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing function

dm: Rename dev_addr..() functions

These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

gpio: bcm2835: add device tree support

This patch adds device tree support for the bcm2835 GPIO driver.

Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

serial: bcm283x_mu: Detect disabled serial device

On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.

However, in such a configurati

serial: bcm283x_mu: Detect disabled serial device

On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.

However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.

This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.

That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

bcm2835_gpio: Implement GPIOF_FUNC

So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.

This patch adds support for determining wheth

bcm2835_gpio: Implement GPIOF_FUNC

So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.

This patch adds support for determining whether a function is mapped as
alternative.

Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

dm: core: Add dev_get_uclass_priv() to access uclass private data

Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses

dm: core: Add dev_get_uclass_priv() to access uclass private data

Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-dm

Fix a trivial conflict over adding <dm.h>

Conflicts:
arch/arm/cpu/armv7/omap3/board.c

Signed-off-by: Tom Rini <trini@ti.com>

dm: gpio: rpi_b: Drop request()/free() in the driver

Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.

Signed-off-by:

dm: gpio: rpi_b: Drop request()/free() in the driver

Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge git://git.denx.de/u-boot-dm

dm: rpi: Convert GPIO driver to driver model

Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.

Signed-off-by: Simon Glass <s

dm: rpi: Convert GPIO driver to driver model

Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>

show more ...

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <s

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'u-boot/master' into u-boot-arm/master

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

ARM: add basic support for the Broadcom BCM2835 SoC

This SoC is used in the Raspberry Pi, for example.

For more details, see:
http://www.broadcom.com/products/BCM2835
http://www.raspberrypi.org/wp-

ARM: add basic support for the Broadcom BCM2835 SoC

This SoC is used in the Raspberry Pi, for example.

For more details, see:
http://www.broadcom.com/products/BCM2835
http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf.

Initial support is enough to boot to a serial console, execute a minimal
set of U-Boot commands, download data over a serial port, and boot a
Linux kernel. No storage or network drivers are implemented.

GPIO driver originally by Vikram Narayanan <vikram186@gmail.com>
with many fixes from myself.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>

show more ...