ARM: at91: fix and update README.at91 document

This patch implement following things
- The link no longer accessable
- Remove the error configuration command
- Update soldered data flash memor

ARM: at91: fix and update README.at91 document

This patch implement following things
- The link no longer accessable
- Remove the error configuration command
- Update soldered data flash memory map
- Update at91sam9m10g45ek memory size to 128MiB

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

show more ...

Power: remove support for Freescale MPC8220

The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.

Remove the code

Power: remove support for Freescale MPC8220

The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.

Remove the code to avoid wasting maitaining efforts on dead stuff.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>

show more ...

doc/README.scrapyard: add missing commit IDs

Signed-off-by: Wolfgang Denk <wd@denx.de>

doc/README.ubi: Add description of accessing ubi filesystems

Signed-off-by: "Paul B. Henson" <henson@acm.org>

Add minor updates to README.fdt-control

A few things have changed since this doc was written, so update it to
match the current state of things.

Signed-off-by: Simon Glass <sjg@chromium.org>

blackfin: Move blackfin watchdog driver out of the blackfin arch folder.

- Enable hw_watchdog_init() in watchdog.h if CONFIG_HW_WATCHDOG is defined.
- Move blackfin hw watchdog driver to the generic

blackfin: Move blackfin watchdog driver out of the blackfin arch folder.

- Enable hw_watchdog_init() in watchdog.h if CONFIG_HW_WATCHDOG is defined.
- Move blackfin hw watchdog driver to the generic driver folder.
- Call hw_watchdog_init() from blackfin board init code.
- Reuse macro CONFIG_WATCHDOG_TIMEOUT_MSECS
- Update README.watchdog accordingly

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

show more ...

Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Conflicts:
drivers/mtd/nand/mxc_nand_spl.c
include/configs/m28evk.h

ARM: OMAP5: Fix warm reset with USB cable connected

Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should b

ARM: OMAP5: Fix warm reset with USB cable connected

Warm reset on OMAP5 freezes when USB cable is connected.
Fix requires PRM_RSTTIME.RSTTIME1 to be programmed
with the time for which reset should be held low for the
voltages and the oscillator to reach stable state.

There are 3 parameters to be considered for calculating
the time, which are mostly board and PMIC dependent.
-1- Time taken by the Oscillator to shut + restart
-2- PMIC OTP times
-3- Voltage rail ramp times, which inturn depends on the
PMIC slew rate and value of the voltage ramp needed.

In order to keep the code in u-boot simple, have a way
for boards to specify a pre computed time directly using
the 'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'
option. If boards fail to specify the time, use a default
as specified by 'CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC' instead.
Using the default value translates into some ~22ms and should work in
all cases.
However in order to avoid this large delay hiding other bugs,
its recommended that all boards look at their respective data
sheets and specify a pre computed and optimal value using
'CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC'

In order to help future board additions to compute this
config option value, add a README at doc/README.omap-reset-time
which explains how to compute the value. Also update the toplevel
README with the additional option and pointers to
doc/README.omap-reset-time.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[rnayak@ti.com: Updated changelog and added the README]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>

show more ...

Fix references to the documentation files

Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them

Fix references to the documentation files

Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

powerpc/p1010rdb: add readme document for p1010rdb

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

doc/ramboot.mpc85xx: Documented the RAMBOOT for MPC85xx

There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SR

doc/ramboot.mpc85xx: Documented the RAMBOOT for MPC85xx

There could be scenarios where the user would like to manually(via JTAG)
configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM.
This document explains thse usecases and the detailed explanation of what needs
to be done to use it.

Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes
of CCSRBAR etc.

The changes are not very large, but it is good to document them so that user
can get it working at once.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>

show more ...

sandbox: Add CONFIG_OF_HOSTFILE to read FDT from host file

With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the addre

sandbox: Add CONFIG_OF_HOSTFILE to read FDT from host file

With sandbox it is tricky to add an FDT to the image at build time (or
later) since we build an ELF file, not a plain binary, and the address
space of the whole U-Boot is not accessible in the emulated memory map
of sandbox.

Sandbox can read files directly from the host, though, so add an option
to read an FDT from a host file on start-up.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

Merge branch 'microblaze' of git://www.denx.de/git/u-boot-microblaze

watchdog: Add support for Xilinx Microblaze watchdog

Watchdog can be used on Microblaze, PPC and Zynq hw designs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@

watchdog: Add support for Xilinx Microblaze watchdog

Watchdog can be used on Microblaze, PPC and Zynq hw designs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>

show more ...

git-mailrc: Add trini shortcut

This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard f

git-mailrc: Add trini shortcut

This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.

Easier for using with patman.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

tools: arm: imx: Implement BOOT_OFFSET command for imximage

Implement BOOT_OFFSET command for imximage. This command is parallel
to current BOOT_FROM command, but allows more flexibility in configur

tools: arm: imx: Implement BOOT_OFFSET command for imximage

Implement BOOT_OFFSET command for imximage. This command is parallel
to current BOOT_FROM command, but allows more flexibility in configuring
arbitrary image header offset. Also add an imximage.cfg with default
offset values into arm/arch/imx-common/ so the board-specific imximage.cfg
can include this file to avoid magic constants.

The syntax of BOOT_OFFSET command is "BOOT_OFFSET <u32 offset>".

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefan Roese <sr@denx.de>

show more ...

imx: Document fuse assignments for MAC addresses

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

Add mxc_ocotp driver

Add an mxc_ocotp driver for i.MX6.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

Add fsl_iim driver

Add a fsl_iim driver common to i.MX and MPC.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

Add fuse API and commands

This can be useful for fuse-like hardware, OTP SoC options, etc.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

feature-removal-schedule.txt: Add CONFIG_SYS_MTEST_START/END

With 'mtest' no longer a default command, we will have unused defines
which should be removed for the v2013.10 release.

Signed-off-by: T

feature-removal-schedule.txt: Add CONFIG_SYS_MTEST_START/END

With 'mtest' no longer a default command, we will have unused defines
which should be removed for the v2013.10 release.

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

config_cmd_default.h: Remove CONFIG_CMD_MEMTEST

As per doc/feature-removal-schedule.txt, remove CONFIG_CMD_MEMTEST from
default list of commands.

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
drivers/video/exynos_fb.c

arm: Remove support for unused s3c64xx

Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the

arm: Remove support for unused s3c64xx

Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>

show more ...