Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014

show more ...

Revert "GCC4.6: Convert various empty macros to inline functions"

This reverts commit 60ce53cf9f408d9ad721f8e7a87d6a564e6d5bac.

The commit causes build breakage for a number of boards. This results

Revert "GCC4.6: Convert various empty macros to inline functions"

This reverts commit 60ce53cf9f408d9ad721f8e7a87d6a564e6d5bac.

The commit causes build breakage for a number of boards. This results
from the fact that now the arguments of debug() actually get
referenced (even if there is hope that the compiler will optimize
away the debug() call). The obvious fix to that probem (change the
code to always declare the referenced variables and data structures)
increases the code size, and was this rejected. So it was decided to
revert this commit until a better solution is found.

show more ...

NAND: Make page, erase, oob size available via cmd_nand

The "nand info" and "nand device" now set shell/environment variables:
nand_writesize ... nand page size
nand_oobsize ..... nand oob area si

NAND: Make page, erase, oob size available via cmd_nand

The "nand info" and "nand device" now set shell/environment variables:
nand_writesize ... nand page size
nand_oobsize ..... nand oob area size
nand_erasesize ... nand erase block size

Also, the "nand info" command now displays this info.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: removed unnecessary memsets]
Signed-off-by: Scott Wood <scottwood@freescale.com>

show more ...

NAND: Add -y option to nand scrub command

This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.

Signed-off-by: Marek Vasut <marek.v

NAND: Add -y option to nand scrub command

This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>

show more ...

NAND: Add nand read.raw and write.raw commands

These commands should work around various "hardware" ECC and BCH methods.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood

NAND: Add nand read.raw and write.raw commands

These commands should work around various "hardware" ECC and BCH methods.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>

show more ...

GCC4.6: Squash warning in cmd_ubi.c:

cmd_ubi.c: In function ‘ubi_volume_read’:
cmd_ubi.c:319:9: warning: variable ‘count_save’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasu

GCC4.6: Squash warning in cmd_ubi.c:

cmd_ubi.c: In function ‘ubi_volume_read’:
cmd_ubi.c:319:9: warning: variable ‘count_save’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

show more ...

GCC4,6: Squash warning in cmd_nand.c

cmd_nand.c: In function ‘do_nand’:
cmd_nand.c:490:7: warning: variable ‘chip’ set but not used
[-Wunused-but-set-variable]
cmd_nand.c:489:7: warning: variable ‘p

GCC4,6: Squash warning in cmd_nand.c

cmd_nand.c: In function ‘do_nand’:
cmd_nand.c:490:7: warning: variable ‘chip’ set but not used
[-Wunused-but-set-variable]
cmd_nand.c:489:7: warning: variable ‘part’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

show more ...

GCC4.6: Squash warning in cmd_mem.c

cmd_mem.c: In function ‘do_mem_loop’:
cmd_mem.c:474:25: warning: variable ‘junk’ set but not used
[-Wunused-but-set-variable]

The assigned variable can be remove

GCC4.6: Squash warning in cmd_mem.c

cmd_mem.c: In function ‘do_mem_loop’:
cmd_mem.c:474:25: warning: variable ‘junk’ set but not used
[-Wunused-but-set-variable]

The assigned variable can be removed because the pointers are volatile so
accesses to their addresses are always generated.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

GCC4.6: Squash warnings in lcd.c

lcd.c: In function ‘lcd_drawchars’:
lcd.c:214:9: warning: variable ‘off’ set but not used
[-Wunused-but-set-variable]
lcd.c: In function ‘lcd_display_bitmap’:
lcd.c:

GCC4.6: Squash warnings in lcd.c

lcd.c: In function ‘lcd_drawchars’:
lcd.c:214:9: warning: variable ‘off’ set but not used
[-Wunused-but-set-variable]
lcd.c: In function ‘lcd_display_bitmap’:
lcd.c:617:16: warning: variable ‘compression’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

GCC4.6: Squash warning in cmd_nvedit.c

cmd_nvedit.c: In function ‘do_env_edit’:
cmd_nvedit.c:463:6: warning: variable ‘len’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <

GCC4.6: Squash warning in cmd_nvedit.c

cmd_nvedit.c: In function ‘do_env_edit’:
cmd_nvedit.c:463:6: warning: variable ‘len’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

GCC4.6: Squash warning in cmd_flash.c

cmd_flash.c: In function ‘do_protect’:
cmd_flash.c:474:6: warning: variable ‘p’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.

GCC4.6: Squash warning in cmd_flash.c

cmd_flash.c: In function ‘do_protect’:
cmd_flash.c:474:6: warning: variable ‘p’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

GCC4.6: Convert various empty macros to inline functions

Fix the following gcc4.6 problems:

cmd_date.c: In function ‘do_date’:
cmd_date.c:50:6: warning: variable ‘old_bus’ set but not used
[-Wunuse

GCC4.6: Convert various empty macros to inline functions

Fix the following gcc4.6 problems:

cmd_date.c: In function ‘do_date’:
cmd_date.c:50:6: warning: variable ‘old_bus’ set but not used
[-Wunused-but-set-variable]
asix.c: In function ‘asix_init’:
asix.c:317:6: warning: variable ‘rx_ctl’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_parse_config’:
usb.c:331:17: warning: variable ‘ch’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_hub_port_connect_change’:
usb.c:1123:29: warning: variable ‘portchange’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_hub_configure’:
usb.c:1183:25: warning: variable ‘hubsts’ set but not used
[-Wunused-but-set-variable]
usb_storage.c: In function ‘usb_stor_CB_reset’:
usb_storage.c:466:6: warning: variable ‘result’ set but not used
[-Wunused-but-set-variable]

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

show more ...

console: Squelch pre-console output in console functions

There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_co

console: Squelch pre-console output in console functions

There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>

show more ...

IDE: Fix complaints about strict aliasing in cmd_ide.c

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Small refactor to remove duplicate serial code

This tidies up duplicate code, and checks that default_serial_console() does
in fact produce a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
A

Small refactor to remove duplicate serial code

This tidies up duplicate code, and checks that default_serial_console() does
in fact produce a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>

show more ...

powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver

Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes

powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver

Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

powerpc/mp: add support for discontiguous cores

Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENT

powerpc/mp: add support for discontiguous cores

Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

show more ...

fdt: Add new fdt_create_phandle helper

Add a helper function that will return a phandle value for the given
node. If the node doesn't have a phandle already one will be created.

Signed-off-by: Kum

fdt: Add new fdt_create_phandle helper

Add a helper function that will return a phandle value for the given
node. If the node doesn't have a phandle already one will be created.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>

show more ...

fdt: Rename fdt_create_phandle to fdt_set_phandle

The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.

Signed-off-

fdt: Rename fdt_create_phandle to fdt_set_phandle

The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>

show more ...

cmd_sf: add "update" subcommand to do smart SPI flash update

This adds a new SPI flash command which only rewrites blocks if the contents
need to change. This can speed up SPI flash programming when

cmd_sf: add "update" subcommand to do smart SPI flash update

This adds a new SPI flash command which only rewrites blocks if the contents
need to change. This can speed up SPI flash programming when much of the
data is unchanged from what is already there.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

show more ...

led: remove camel casing of led identifiers globally

Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
'

led: remove camel casing of led identifiers globally

Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done

Discussion:
http://patchwork.ozlabs.org/patch/84988/

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

show more ...

utx8245: fix build breakage due to assert()

Commit 21726a7 "Add assert() for debug assertions" broke building the
utx8245 board:

dlmalloc.c: In function 'do_check_chunk':
dlmalloc.c:1660: error: 's

utx8245: fix build breakage due to assert()

Commit 21726a7 "Add assert() for debug assertions" broke building the
utx8245 board:

dlmalloc.c: In function 'do_check_chunk':
dlmalloc.c:1660: error: 'sz' undeclared (first use in this function)
dlmalloc.c:1660: error: (Each undeclared identifier is reported only once
dlmalloc.c:1660: error: for each function it appears in.)
dlmalloc.c: In function 'do_check_free_chunk':
dlmalloc.c:1689: error: 'next' undeclared (first use in this function)
dlmalloc.c: In function 'do_check_malloced_chunk':
dlmalloc.c:1748: error: 'sz' undeclared (first use in this function)
dlmalloc.c:1750: error: 'room' undeclared (first use in this function)

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>

show more ...

Add assert() for debug assertions

assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined.
This is useful when a condition is an error but a board reset is unlikely
to fix it, so i

Add assert() for debug assertions

assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined.
This is useful when a condition is an error but a board reset is unlikely
to fix it, so it is better to soldier on in hope. Assertion failures should
be caught during development/test.

It turns out that assert() is defined separately in a few places in U-Boot
with various meanings. This patch cleans up some of these.

Build errors exposed by this change (and defining DEBUG) are also fixed in
this patch.

Signed-off-by: Simon Glass <sjg@chromium.org>

show more ...

YAFFS2: cmd_yaffs2.c - fix build warnings

Fix these:
cmd_yaffs2.c: In function 'do_ywr':
cmd_yaffs2.c:69: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'ulong'
cmd_yaffs2

YAFFS2: cmd_yaffs2.c - fix build warnings

Fix these:
cmd_yaffs2.c: In function 'do_ywr':
cmd_yaffs2.c:69: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'ulong'
cmd_yaffs2.c:69: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'ulong'

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

common: fix behavior of ROUND macro when input is already rounded

Currently when you call ROUND with a value that is already a
multiple of the second parameter it will return a value that is
one mul

common: fix behavior of ROUND macro when input is already rounded

Currently when you call ROUND with a value that is already a
multiple of the second parameter it will return a value that is
one multiple larger, instead of returning the value passed in.

There are only two types of usage of ROUND currently, one in
various config files to round CONFIG_SYS_MALLOC_LEN to a multiple
of 4096 bytes. The other in cmd_sf.c where the incorrect behavior
of ROUND is worked around be subtracting one from the length argument
before passing it to ROUND.

This patch fixes ROUND and removes the workaround from cmd_sf. It
also results in all of the malloc pools that use ROUND to compute
their size shrinking by 4KB.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mike Frysinger <vapier@gentoo.org>

show more ...