arm: mvebu: theadorable: Add 'pcie' test command

This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will

arm: mvebu: theadorable: Add 'pcie' test command

This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: theadorable: Add board-specific PEX detection pulse width

Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the defaul

arm: mvebu: theadorable: Add board-specific PEX detection pulse width

Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).

In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

This mainly adds support for some new boards, like the ARMv8 community
boards MACCHIATOBin and ESPRESSBin

arm: mvebu: theadorable: Add 'pcie' test command

This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will

arm: mvebu: theadorable: Add 'pcie' test command

This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: theadorable: Add board-specific PEX detection pulse width

Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the defaul

arm: mvebu: theadorable: Add board-specific PEX detection pulse width

Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).

In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: theadorable: Configure board for PCIe 2.0 capability

Use a board-specific board_sat_r_get() function to configure the board
for PCIe 2.0 capability (e.g. 5GB/s link speed). Otherwise the

arm: mvebu: theadorable: Configure board for PCIe 2.0 capability

Use a board-specific board_sat_r_get() function to configure the board
for PCIe 2.0 capability (e.g. 5GB/s link speed). Otherwise the default
of 2.5GB/s will be established.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

arm: mvebu: theadorable: Remove Board name output in checkboard

This line is not needed, as the board supports DT based probing. And
here the "Model:" is already printed:

Model: Marvell Armada XP t

arm: mvebu: theadorable: Remove Board name output in checkboard

This line is not needed, as the board supports DT based probing. And
here the "Model:" is already printed:

Model: Marvell Armada XP theadorable
Board: theadorable

One line for the board name is enough.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: theadorable: Add PEX-switch detection and reset code

Sometimes the PCIe link for the PEX-switch will not come-up. In this case,
the board is not in a usable state. This patch makes sure

arm: mvebu: theadorable: Add PEX-switch detection and reset code

Sometimes the PCIe link for the PEX-switch will not come-up. In this case,
the board is not in a usable state. This patch makes sure that in this
case a soft-reset is issued. If this soft-reset does not result in the
PEX-switch being detected after some soft-reset cycles, an I2C message
is sent to the uC to issue a complete power-cycle of the board.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: theadorable: Add USB power toggle and tweak USB PHY register

This patch adds an USB power toggle for theadorable. Additionally, the
USB PHY RX Channel Control 0 Register is changed to fi

arm: mvebu: theadorable: Add USB power toggle and tweak USB PHY register

This patch adds an USB power toggle for theadorable. Additionally, the
USB PHY RX Channel Control 0 Register is changed to fix some issues
noticed while accessing some specific USB sticks.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://www.denx.de/git/u-boot-marvell

arm: mvebu: theadorable: Add StratixV FPGA programming support

This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board speci

arm: mvebu: theadorable: Add StratixV FPGA programming support

This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board specific write
code to program the bitstream via SPI direct write mode.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

arm: mvebu: Add support for the Armada XP theadorable board

This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,

arm: mvebu: Add support for the Armada XP theadorable board

This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.

Two defconfigs are added:

theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.

theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>

show more ...