Merge git://git.denx.de/u-boot-mmc

dm: sata: sunxi: Add support for driver model

Adjust SATA setup to support driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: Turn satapwr on from board_init

There are 2 reasons for doing this:

1) The main reason for doing this is to move it outside of
board/sunxi/ahci.c, so that it can be used on boards which u

sunxi: Turn satapwr on from board_init

There are 2 reasons for doing this:

1) The main reason for doing this is to move it outside of
board/sunxi/ahci.c, so that it can be used on boards which use
a usb<->sata chip too;
2) While doing this I realized that doing it from board_init also meant
doing it much earlier. Some printf get_timer(0) calls show that the
time between board_init() and scsi_init() is more then 600 ms,
so we can drop the mdelay(500)

While at it also drop the printf("SUNXI SCSI INIT\n") AHCI init is
noisy enough by itself.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

ahci: mmio_base is a virtual address

Don't store it in a u32.

Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a2b4 ("ahci: Support splitting of read transactions
i

ahci: mmio_base is a virtual address

Don't store it in a u32.

Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a2b4 ("ahci: Support splitting of read transactions
into multiple chunks")).

Fixes crash on boot in MPC8641HPCN_36BIT target.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>

show more ...

Merge branch 'master' of http://git.denx.de/u-boot-sunxi

sunxi: ahci: Add a delay after enabling target power

If the target power is connected through a gpio, then give the target some
time to power up before continuing with ahci / sata probing, this avoi

sunxi: ahci: Add a delay after enabling target power

If the target power is connected through a gpio, then give the target some
time to power up before continuing with ahci / sata probing, this avoids
link timeouts, without penalizing other boards where there is no target
power gpio.

Why 500 ms ? I started with 200, that was not enough, then I went to 500 which
worked, lowering it to 350 broke things again, so 500 seems the minimum my
vertex2 needs to be ready to get probed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

show more ...

Merge git://www.denx.de/git/u-boot-sunxi

dm: sunxi: Make sure that GPIOs are requested

The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just

dm: sunxi: Make sure that GPIOs are requested

The scsi_init() function uses a GPIO so should request it. There is no
way to return an error here, and the request may be made multiple times,
so just ignore errors for now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-arm

Merge branch 'master' of git://git.denx.de/u-boot-arm

Conflicts:
boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master'

ahci: provide sunxi SATA driver using AHCI platform framework

This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi pla

ahci: provide sunxi SATA driver using AHCI platform framework

This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.

The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.

The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.

This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

show more ...